pata_hpt3x3: major reworking and testing

The HPT343/345 (aka 363) is a bit of a warped device.  For many setups you
need to access the other registers via BAR4 offsets.  PIO is now rock
solid, DMA isn't.  Unfortunately the drivers/ide hpt34x driver is
completely broken so doesn't help further debug.

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This commit is contained in:
Alan Cox 2007-07-09 11:46:22 -07:00 committed by Jeff Garzik
parent 75683fe715
commit 66e7da4e34
2 changed files with 84 additions and 14 deletions

View File

@ -309,7 +309,7 @@ config PATA_HPT3X2N
If unsure, say N.
config PATA_HPT3X3
tristate "HPT 343/363 PATA support (Experimental)"
tristate "HPT 343/363 PATA support"
depends on PCI
help
This option enables support for the HPT 343/363
@ -317,6 +317,14 @@ config PATA_HPT3X3
If unsure, say N.
config PATA_HPT3X3_DMA
bool "HPT 343/363 DMA support (Experimental)"
depends on PATA_HPT3X3
help
This option enables DMA support for the HPT343/363
controllers. Enable with care as there are still some
problems with DMA on this chipset.
config PATA_ISAPNP
tristate "ISA Plug and Play PATA support (Experimental)"
depends on EXPERIMENTAL && ISAPNP

View File

@ -23,7 +23,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x3"
#define DRV_VERSION "0.4.3"
#define DRV_VERSION "0.5.3"
/**
* hpt3x3_set_piomode - PIO setup
@ -59,6 +59,9 @@ static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev)
*
* Set up the channel for MWDMA or UDMA modes. Much the same as with
* PIO, load the mode number and then set MWDMA or UDMA flag.
*
* 0x44 : bit 0-2 master mode, 3-5 slave mode, etc
* 0x48 : bit 4/0 DMA/UDMA bit 5/1 for slave etc
*/
static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
@ -76,14 +79,26 @@ static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */
if (adev->dma_mode >= XFER_UDMA_0)
r2 |= 0x01 << dn; /* Ultra mode */
r2 |= (0x10 << dn); /* Ultra mode */
else
r2 |= 0x10 << dn; /* MWDMA */
r2 |= (0x01 << dn); /* MWDMA */
pci_write_config_dword(pdev, 0x44, r1);
pci_write_config_dword(pdev, 0x48, r2);
}
/**
* hpt3x3_atapi_dma - ATAPI DMA check
* @qc: Queued command
*
* Just say no - we don't do ATAPI DMA
*/
static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc)
{
return 1;
}
static struct scsi_host_template hpt3x3_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
@ -105,7 +120,6 @@ static struct scsi_host_template hpt3x3_sht = {
static struct ata_port_operations hpt3x3_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = hpt3x3_set_piomode,
.set_dmamode = hpt3x3_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
@ -124,6 +138,7 @@ static struct ata_port_operations hpt3x3_port_ops = {
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.check_atapi_dma= hpt3x3_atapi_dma,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
@ -158,32 +173,79 @@ static void hpt3x3_init_chipset(struct pci_dev *dev)
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
}
/**
* hpt3x3_init_one - Initialise an HPT343/363
* @dev: PCI device
* @pdev: PCI device
* @id: Entry in match table
*
* Perform basic initialisation. The chip has a quirk that it won't
* function unless it is at XX00. The old ATA driver touched this up
* but we leave it for pci quirks to do properly.
* Perform basic initialisation. We set the device up so we access all
* ports via BAR4. This is neccessary to work around errata.
*/
static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static int printed_version;
static const struct ata_port_info info = {
.sht = &hpt3x3_sht,
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
#if defined(CONFIG_PATA_HPT3X3_DMA)
/* Further debug needed */
.mwdma_mask = 0x07,
.udma_mask = 0x07,
#endif
.port_ops = &hpt3x3_port_ops
};
/* Register offsets of taskfiles in BAR4 area */
static const u8 offset_cmd[2] = { 0x20, 0x28 };
static const u8 offset_ctl[2] = { 0x36, 0x3E };
const struct ata_port_info *ppi[] = { &info, NULL };
struct ata_host *host;
int i, rc;
void __iomem *base;
hpt3x3_init_chipset(dev);
/* Now kick off ATA set up */
return ata_pci_init_one(dev, ppi);
hpt3x3_init_chipset(pdev);
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host)
return -ENOMEM;
/* acquire resources and fill host */
rc = pcim_enable_device(pdev);
if (rc)
return rc;
/* Everything is relative to BAR4 if we set up this way */
rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME);
if (rc == -EBUSY)
pcim_pin_device(pdev);
if (rc)
return rc;
host->iomap = pcim_iomap_table(pdev);
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
base = host->iomap[4]; /* Bus mastering base */
for (i = 0; i < host->n_ports; i++) {
struct ata_ioports *ioaddr = &host->ports[i]->ioaddr;
ioaddr->cmd_addr = base + offset_cmd[i];
ioaddr->altstatus_addr =
ioaddr->ctl_addr = base + offset_ctl[i];
ioaddr->scr_addr = NULL;
ata_std_ports(ioaddr);
ioaddr->bmdma_addr = base + 8 * i;
}
pci_set_master(pdev);
return ata_host_activate(host, pdev->irq, ata_interrupt, IRQF_SHARED,
&hpt3x3_sht);
}
#ifdef CONFIG_PM