This patch fixes a bug introduced when moving some code around for
readability.
Setting the wqe pointer at the end of the function is a NOP since it
isn't used. Move it back to where it is used.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In ipath_query_device(), some of the struct ib_device_attr fields were
not being initialized.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Although our chip supports 4K MTUs, our driver doesn't yet support
this feature, so limit the maximum MTU to 2K until we get support for
4K MTUs implemented.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Recognize IBA 6110 Revision 4: same feature set, etc. as earlier revisions.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We currently track various errors, now we enhance that capability by
logging some of them to EEPROM. We also now log a cumulative "active"
time defined by traffic though the InfiniPath HCA beyond the normal SM
traffic.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPATH_RUNTIME_PBC_REWRITE and the IPATH_RUNTIME_LOOSE_DMA_ALIGN
flags were not ever implemented correctly and did not turn out to be
necessary. Remove the last vestiges of these flags but mark the spot
with a comment to remind us to not reuse these flags in the interest
of binary compatibility. The INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR
bit was also not found to be useful, so it was dropped in the cleanup
as well.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new LED blinking interface adds more contention for the
unprotected GPIO pins that were already shared, though not commonly at
the same time. We add locks to the accesses to these pins so that
Read-Modify-Write is now safe. Some of these locks are added at
interrupt context, so we shadow the registers which drive and inspect
these pins to avoid the mmio read/writes. This mitigates the effects
of the locks and hastens us through the interrupt.
Add locking and always use shadows for registers controlling GPIO pins
(ExtCtrl and GPIOout). The use of shadows implies doing less I/O,
which can make I2C operation too fast on some platforms. An explicit
udelay(1) in SCL manipulation fixes that.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we want to find an InfiniPath HCA in a rack of nodes, it is often
expeditious to blink the status LEDs via a userspace /sys file.
A write-only led_override "file" is published per device. Writes to
this file are interpreted as (string form) numbers, and the resulting
value sent to ipath_set_led_override(). The upper eight bits are
interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom
two 4-bit values are alternately (D0..3, then D4..7) used by the
board-specific LED-setting function to override the normal state.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_ib.h uses struct mutex, so although <linux/mutex.h> seems to be
pulled in indirectly by one of the headers it includes, the right
thing is to include <linux/mutex.h> directly.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Refactor the ehca changes from commit ed23a727 ("IB: Return "maybe
missed event" hint from ib_req_notify_cq()") so the queue arithmetic
is done in slightly fewer lines. Also, move the spinlock flags into
the block they're used in.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to keep a spare entry in the SRQ so that there always is a
next WQE available when posting receives (so that we can tell the
difference between a full queue and an empty queue). So subtract 1
from the value HW gives us before reporting the limit on SRQ entries
to consumers.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Inline data segments in send WQEs are not allowed to cross a 64 byte
boundary. We use inline data segments to hold the UD headers for MLX
QPs (QP0 and QP1). A send with GRH on QP1 will have a UD header that
is too big to fit in a single inline data segment without crossing a
64 byte boundary, so split the header into two inline data segments.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set. Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When compacting CQ entries, we need to set the correct value of the
ownership bit in case the value is different between the index we copy
the CQE from and the index we copy it to.
Found by Ronni Zimmerman of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The calculation of max_inline_data in set_kernel_sq_size() is bogus,
since it doesn't take into account the fact that inline segments may
not cross a 64-byte boundary, and hence multiple inline segments will
probably need to be used to post large inline sends.
We don't support inline sends for kernel QPs anyway, so there's no
point in doing this calculation anyway, since the field is just zeroed
out a little later. So just delete the bogus calculation.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
New ConnectX firmware introduces FW command interface revision 2,
which requires that for each QP, a chunk of send queue entries (the
"headroom") is kept marked as invalid, so that the HCA doesn't get
confused if it prefetches entries that haven't been posted yet. Add
code to the driver to do this, and also update the user ABI so that
userspace can request that the prefetcher be turned off for userspace
QPs (we just leave the prefetcher on for all kernel QPs).
Unfortunately, marking send queue entries this way is confuses older
firmware, so we change the driver to allow only FW command interface
revisions 2. This means that users will have to update their firmware
to work with the new driver, but the firmware is changing quickly and
the old firmware has lots of other bugs anyway, so this shouldn't be too
big a deal.
Based on a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Doing max(1, foo) where foo is u32 generates a warning, because 1 is a
signed constant. Fix this by using 1U instead.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cast the increment added to wq->tail when send completions are
processed to u16 to avoid using wrong values caused by standard
integer promotions.
The same bug was fixed in libmlx4 by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Make sure RQ allocation is always valid
RDMA/cma: Fix initialization of next_port
IB/mlx4: Fix zeroing of rnr_retry value in ib_modify_qp()
mlx4_core: Don't set MTT address in dMPT entries with PA set
mlx4_core: Check firmware command interface revision
IB/mthca, mlx4_core: Fix typo in comment
mlx4_core: Free catastrophic error MSI-X interrupt with correct dev_id
mlx4_core: Initialize ctx_list and ctx_lock earlier
mlx4_core: Fix CQ context layout
QPs attached to an SRQ must never have their own RQ, and QPs not
attached to SRQs must have an RQ with at least 1 entry. Enforce all
of this in set_rq_size().
Based on a patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code in __mlx4_ib_modify_qp() overwrites context->params1 after
the RNR retry parameter is ORed in, which results in the RNR retry
parameter always being set to 0. Fix this by moving where we OR in
the value to later in the function, after the initial assignment of
context->params1.
Found by the Mellanox firmware group.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch converts the ipv4_devconf config members (everything except
sysctl) to an array. This allows easier manipulation which will be
needed later on to provide better management of default config values.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
mthca_free_err_wqe() currently treats both send and receive CQEs
identically if a QP is using an SRQ. But for Tavor hardware, send
CQEs with error can be chained together even if the RQ is part of SRQ,
so we may miss some CQEs.
Fix by following the WQE chain for all send CQEs even for non-SRQ QPs.
This fixes crashes in IPoIB CM:
<https://bugs.openfabrics.org//show_bug.cgi?id=604>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to a typo, the driver was reporting the wrong number of "actual send
WRs" after ehca_create_qp().
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to initialize the owner bit of send queue WQEs to hardware
ownership whenever the QP is modified from reset to init, not just
when the QP is first allocated. This avoids having the hardware
process stale WQEs when the QP is moved to reset but not destroyed and
then modified to init again.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a QP is attached to a shared receive queue (SRQ), then it doesn't
have a receive queue (RQ). So don't allocate an RQ doorbell (or map a
doorbell from userspace for userspace QPs) for that QP.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/cm: Improve local id allocation
IPoIB/cm: Fix SRQ WR leak
IB/ipoib: Fix typos in error messages
IB/mlx4: Check if SRQ is full when posting receive
IB/mlx4: Pass send queue sizes from userspace to kernel
IB/mlx4: Fix check of opcode in mlx4_ib_post_send()
mlx4_core: Fix array overrun in dump_dev_cap_flags()
IB/mlx4: Fix RESET to RESET and RESET to ERROR transitions
IB/mthca: Fix RESET to ERROR transition
IB/mlx4: Set GRH:HopLimit when sending globally routed MADs
IB/mthca: Set GRH:HopLimit when building MLX headers
IB/mlx4: Fix check of max_qp_dest_rdma in modify QP
IB/mthca: Fix use-after-free on device restart
IB/ehca: Return proper error code if register_mr fails
IPoIB: Handle P_Key table reordering
IB/core: Use start_port() and end_port()
IB/core: Add helpers for uncached GID and P_Key searches
IB/ipath: Fix potential deadlock with multicast spinlocks
IB/core: Free umem when mm is already gone
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass the number of WQEs for the send queue and their size from userspace
to the kernel to avoid having to keep the QP size calculations in sync
between the kernel driver and libmlx4. This fixes a bug seen with the
current mlx4_ib driver and current libmlx4 caused by a difference in the
calculated sizes for SQ WQEs. Also, this gives more flexibility for
userspace to experiment with using multiple WQE BBs for a single SQ WQE.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
wr->opcode is invalid if it's >= ARRAY_SIZE(mlx4_ib_opcode), not just
strictly >.
This was spotted by the Coverity checker (CID 1643).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the IB spec, a QP can be moved from RESET back to RESET
or to the ERROR state, but mlx4 firmware does not support this and
returns an error if we try. Fix the RESET to RESET transition by
just returning 0 without doing anything, and fix RESET to ERROR by
moving the QP from RESET to INIT with dummy parameters and then
transitioning from INIT to ERROR.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the IB spec, a QP can be moved from RESET to the ERROR
state, but mthca firmware does not support this and returns an error if
we try. Work around this FW limitation by moving the QP from RESET to
INIT with dummy parameters and then transitioning from INIT to ERROR.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Global CM packets used by rmda_cm were being sent with a GRH:hopLimit
of zero, causing them to be dropped by the router. The problem is a
missing initialization of the hop_limit field in mthca_read_ah(),
which was called by build_mlx_header() when sending a MAD on QP1.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
max_qp_dest_rdma is already in natural units - no need to shift. This
was discovered by a test that deliberately requests more outstanding
atomic operation than the device supports.
Found by Sagi Rotem at Mellanox.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the return code of ehca_register_mr() to ENOMEM if the corresponding
firmware call fails due to out of resources. Some other error codes
were explicitly mapped to EINVAL -- just remove those cases so they
get mapped to the default case, which already returns EINVAL anyway.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Lockdep found the following potential deadlock between mcast_lock and
n_mcast_grps_lock: mcast_lock is taken from both interrupt context and
process context, so spin_lock_irqsave() must be used to take it.
n_mcast_grps_lock is only taken from process context, so at first it
seems safe to take it with plain spin_lock(); however, it also nests
inside mcast_lock, and hence we could deadlock:
cpu A cpu B
ipath_mcast_add():
spin_lock_irq(&mcast_lock);
ipath_mcast_detach():
spin_lock(&n_mcast_grps_lock);
<enter interrupt>
ipath_mcast_find():
spin_lock_irqsave(&mcast_lock);
spin_lock(&n_mcast_grps_lock);
Fix this by using spin_lock_irq() to take n_mcast_grps_lock.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_cq_clean() updates the CQ consumer index without moving CQEs
back to HW ownership. As a result, the same WRID might get reported
twice, resulting in a use-after-free. This was observed in IPoIB CM.
Fix by moving all freed CQEs to HW ownership.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=617>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix posting lists of > 255 receive WRs for Tavor: rq.next_ind must
be updated each doorbell, otherwise the next doorbell will use an
incorrect index.
Found by Ronni Zimmermann at Mellanox.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Scaling code is still considered experimental, so disable it by default
- Increase version to SVNEHCA_0023
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eHCA's sysfs attributes are now being created via sysfs_create_group(),
making the process neatly table-driven. The return value is checked, thus
fixing a few compiler warnings.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- In ehca_process_eq(), we're IRQ safe throughout the whole function, so we
don't need another _irqsave in the middle of flight.
- take_over_work() is only called by comp_pool_callback(), so it can move
into the same #ifdef block.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
AQP0/1 should report qp_num={0|1} and the actual QP# should be stored
in struct ehca_qp, not the other way round.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver needs to always supply the "GRH present" flag to the
hypervisor, whether it's true or false. Not supplying it (i.e. not
setting the corresponding mask bit) amounts to a "perhaps", which we
don't want.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some pSeries hypervisor versions show a race condition in the allocate
MR hCall. Serialize this call per adapter to circumvent this problem.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Once upon a time, GPIO interrupts were rare. But then a chip bug in
the waldo series forced the use of a GPIO interrupt to signal packet
reception. This greatly increased the frequency of GPIO interrupts
which have the gpio_mask bits set on the waldo chips. Other bits in
the gpio_status register are used for I2C clock and data lines, these
bits are usually on. An "unlikely" annotation leftover from the old
days was improperly applied to these bits, and an unnecessary chip
mmio read was being accessed in the interrupt fast path on waldo.
Remove the stagnant unlikely annotation in the interrupt handler and
keep a shadow copy of the gpio_mask register to avoid the slow mmio
read when testing for interruptable GPIO bits.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
uar_lock spinlock was used in mlx4_ib_cq_arm without being initialized
(this only affects 32-bit archs, because uar_lock is not used on
64-bit archs and MLX4_INIT_DOORBELL_LOCK() is a NOP).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters
IB: Put rlimit accounting struct in struct ib_umem
IB/uverbs: Export ib_umem_get()/ib_umem_release() to modules
Since nonboot CPUs are now disabled after tasks and devices have been
frozen and the CPU hotplug infrastructure is used for this purpose, we need
special CPU hotplug notifications that will help the CPU-hotplug-aware
subsystems distinguish normal CPU hotplug events from CPU hotplug events
related to a system-wide suspend or resume operation in progress. This
patch introduces such notifications and causes them to be used during
suspend and resume transitions. It also changes all of the
CPU-hotplug-aware subsystems to take these notifications into consideration
(for now they are handled in the same way as the corresponding "normal"
ones).
[oleg@tv-sign.ru: cleanups]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an InfiniBand driver for Mellanox ConnectX adapters. Because
these adapters can also be used as ethernet NICs and Fibre Channel
HBAs, the driver is split into two modules:
mlx4_core: Handles low-level things like device initialization and
processing firmware commands. Also controls resource allocation
so that the InfiniBand, ethernet and FC functions can share a
device without stepping on each other.
mlx4_ib: Handles InfiniBand-specific things; plugs into the
InfiniBand midlayer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export ib_umem_get()/ib_umem_release() and put low-level drivers in
control of when to call ib_umem_get() to pin and DMA map userspace,
rather than always calling it in ib_uverbs_reg_mr() before calling the
low-level driver's reg_user_mr method.
Also move these functions to be in the ib_core module instead of
ib_uverbs, so that driver modules using them do not depend on
ib_uverbs.
This has a number of advantages:
- It is better design from the standpoint of making generic code a
library that can be used or overridden by device-specific code as
the details of specific devices dictate.
- Drivers that do not need to pin userspace memory regions do not
need to take the performance hit of calling ib_mem_get(). For
example, although I have not tried to implement it in this patch,
the ipath driver should be able to avoid pinning memory and just
use copy_{to,from}_user() to access userspace memory regions.
- Buffers that need special mapping treatment can be identified by
the low-level driver. For example, it may be possible to solve
some Altix-specific memory ordering issues with mthca CQs in
userspace by mapping CQ buffers with extra flags.
- Drivers that need to pin and DMA map userspace memory for things
other than memory regions can use ib_umem_get() directly, instead
of hacks using extra parameters to their reg_phys_mr method. For
example, the mlx4 driver that is pending being merged needs to pin
and DMA map QP and CQ buffers, but it does not need to create a
memory key for these buffers. So the cleanest solution is for mlx4
to call ib_umem_get() in the create_qp and create_cq methods.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes it so that simple_fill_super and get_sb_pseudo assign their
root inodes to be number 1. It also fixes up a couple of callers of
simple_fill_super that were passing in files arrays that had an index at
number 1, and adds a warning for any caller that sends in such an array.
It would have been nice to have made it so that it wasn't possible to make
such a collision, but some callers need to be able to control what inode
number their entries get, so I think this is the best that can be done.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Convert to NAPI
IB: Return "maybe missed event" hint from ib_req_notify_cq()
IB: Add CQ comp_vector support
IB/ipath: Fix a race condition when generating ACKs
IB/ipath: Fix two more spin lock problems
IB/fmr_pool: Add prefix to all printks
IB/srp: Set proc_name
IB/srp: Add orig_dgid sysfs attribute to scsi_host
IPoIB/cm: Don't crash if remote side uses one QP for both directions
RDMA/cxgb3: Support for new abort logic
RDMA/cxgb3: Initialize cpu_idx field in cpl_close_listserv_req message
RDMA/cxgb3: Fail qp creation if the requested max_inline is too large
RDMA/cxgb3: Fix TERM codes
IPoIB/cm: Fix error handling in ipoib_cm_dev_open()
IB/ipath: Don't corrupt pending mmap list when unmapped objects are freed
IB/mthca: Work around kernel QP starvation
IB/ipath: Don't put QP in timeout queue if waiting to send
IB/ipath: Don't call spin_lock_irq() from interrupt context
The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested. In
other words, this means that the following race is possible:
while (CQ is not empty)
ib_poll_cq(CQ);
// new completion is added after while loop is exited
ib_req_notify_cq(CQ);
// no event is generated for the existing completion
To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.
However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification). Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.
Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:
< 0 means an error occurred while requesting notification
== 0 means notification was requested successfully, and if
IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
events were missed and it is safe to wait for another
event.
> 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was
passed in. It means that the consumer must poll the
CQ again to make sure it is empty to avoid the race
described above.
We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a problem where simple ACKs can be sent ahead of RDMA read
responses thus implicitly NAKing the RDMA read.
Signed-off-by: Ralph Campbell <ralph.cambpell@qlogic.com>
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a missing unlock in ipath_rc_rcv_resp() and remove an extra unlock
from ipath_rc_rcv_error().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages. We need
to handle them by silenty dropping the 1st but mark that we're ready
for the final message. This plugs some close races between the uP and
HW. Also update the minimum required firmware version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix TERMINATE layer, type, and ecode values based on
conformance testing.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the pending mmap code so it doesn't corrupt the list of pending
mmaps and crash the machine when pending mmaps are destroyed without
first being mapped. Also, remove an unused variable, and use standard
kernel lists instead of our own homebrewed linked list implementation
to keep the pending mmap list.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With mthca, RC QPs can starve each other and even UD QPs on the same
hardware schedule queue. As a result, userspace MPI can starve
e.g. IPoIB traffic, with netdev watchdog warnings getting printed out,
and TCP connections getting stuck or failing.
Reduce the chance of this happening by using three separate hardware
schedule queues: one for userspace RC QPs, one for kernel RC QPs, and
one for all other QPs.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes a problem which causes too many RC timeouts and
retransmits.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the problem reported by Bernd Schubert <bs@q-leap.de>
with kernel debug options enabled:
BUG: at kernel/lockdep.c:1860 trace_hardirqs_on()
This was caused by using spin_lock_irq()/spin_unlock_irq() from
interrupt context. Fix all the places that might be called from
interrupts to use spin_lock_irqsave()/spin_unlock_irqrestore().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: (49 commits)
IB: Set class_dev->dev in core for nice device symlink
IB/ehca: Implement modify_port
IB/umad: Clarify documentation of transaction ID
IPoIB/cm: spin_lock_irqsave() -> spin_lock_irq() replacements
IB/mad: Change SMI to use enums rather than magic return codes
IB/umad: Implement GRH handling for sent/received MADs
IB/ipoib: Use ib_init_ah_from_path to initialize ah_attr
IB/sa: Set src_path_bits correctly in ib_init_ah_from_path()
IB/ucm: Simplify ib_ucm_event()
RDMA/ucma: Simplify ucma_get_event()
IB/mthca: Simplify CQ cleaning in mthca_free_qp()
IB/mthca: Fix mthca_write_mtt() on HCAs with hidden memory
IB/mthca: Update HCA firmware revisions
IB/ipath: Fix WC format drift between user and kernel space
IB/ipath: Check that a UD work request's address handle is valid
IB/ipath: Remove duplicate stuff from ipath_verbs.h
IB/ipath: Check reserved memory keys
IB/ipath: Fix unit selection when all CPU affinity bits set
IB/ipath: Don't allow QPs 0 and 1 to be opened multiple times
IB/ipath: Disable IB link earlier in shutdown sequence
...
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Now to convert the last one, skb->data, that will allow many simplifications
and removal of some of the offset helpers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All RDMA drivers except ehca set class_dev->dev to their dma_device
value (ehca leaves this unset). dma_device is the only value that
makes any sense, so move this assignment to core/sysfs.c. This reduce
the duplicated code in the rest of the drivers and gives ehca a nice
/sys/class/infiniband/ehcaX/device symlink.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add "Modify Port" verb support to eHCA driver. The IB communication
manager needs this to set the IsCM port capability bit when
initializing.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_free_qp() already has local variables to hold the QP's send_cq
and recv_cq, so we can slightly clean up the calls to mthca_cq_clean()
by using those local variables instead of expressions like
to_mcq(qp->ibqp.send_cq).
Also, by cleaning the recv_cq first, we can avoid worrying about
whether the QP is attached to an SRQ for the second call, because we
would only clean send_cq if send_cq is not equal to recv_cq, and that
means send_cq cannot have any receive completions from the QP being
destroyed.
All this work even improves the generated code a bit:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-5 (-5)
function old new delta
mthca_free_qp 510 505 -5
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit b2875d4c ("IB/mthca: Always fill MTTs from CPU") causes a crash
in mthca_write_mtt() with non-memfree HCAs that have their memory
hidden (that is, have only two PCI BARs instead of having a third BAR
that allows access to the RAM attached to the HCA) on 64-bit
architectures. This is because the commit just before, c20e20ab
("IB/mthca: Merge MR and FMR space on 64-bit systems") makes
dev->mr_table.fmr_mtt_buddy equal to &dev->mr_table.mtt_buddy and
hence mthca_write_mtt() tries to write directly into the HCA's MTT
table. However, since that table is in the HCA's memory, this is
impossible without the PCI BAR that gives access to that memory.
This causes a crash because mthca_tavor_write_mtt_seg() basically
tries to dereference some offset of a NULL pointer. Fix this by
adding a test of MTHCA_FLAG_FMR in mthca_write_mtt() so that we always
use the WRITE_MTT firmware command rather than writing directly if
FMRs are not enabled.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The kernel ib_wc structure now uses a QP pointer, but the user space
equivalent uses a QP number instead. This means we can no longer use
a simple structure copy to copy stuff into user space.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't let userspace use the direct-physical-map L_key or R_key.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At some point things changed so that all the affinity bits can be set,
but cpus_full() macro is not true. This caused problems with the unit
selection logic on multi-unit (board) configurations.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the code that shuts down the IB link earlier in the unload
process, to be sure no new packets can arrive while we are unloading.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To prevent random utility reads and writes of the diag interface to the
chip, we first require a handshake of reading from offset 0 and writing
to offset 0 before any other reads or writes can be done through the
diags device. Otherwise chip errors can be triggered.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the chip is no longer usable, LEDs should be turned off so system
can be found easily in the cluster.
Also some minor reorganizing so both chips print hardware error
message at same point and only if there were unrecovered errors
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Re-init of the kernel structures after a chip reset was leaving the
portdata structure for port zero in an inconsistent state, and a
pointer to it either stale (in re-init code) or NULL (in devdata)
Fixing the order of operations on this struct, and the condition for
interrupt access, prevents the crashes.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to a chip bug, the PIOAvail register is not always updated to
memory. This patch allows userspace to force an update.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In initialization, if we bailed at chip specific initialization, we
forgot to clean up the irq we had requested.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a bug where multicast packets without a GRH were not
being dropped as per the IB spec.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the module parameter "kpiobufs" is set too high, the calculation to
reset it to a sane value was incorrect.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix RDMA read response length checking for RDMA_READ_RESPONSE_ONLY to
allow a zero length response. RDMA read responses which don't match
the expected length or occur in response to some other operation
should generate a completion queue error (see table 56, ch. 9.9.2.3 in
the IB spec).
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve port-sharing performance by allowing any process to receive
packets from the shared hardware port under a spin lock for mutual
exclusion. Previously, one process was nominated as the master and
that process was responsible for receiving all packets from the shared
hardware port and either consuming them or forwarding them to their
destination. This led to starvation problems for other processes when
the master process was busy in computation phases.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The port sharing feature mixed kernel virtual addresses as well as
physical addresses for the offset used to describe the mmap address to
map the InfiniPath hardware into user space. This had a conflict on
powerpc. The new scheme converts it to a physical address so it
doesn't conflict with chip addresses and yet still fits in 40/44 bits
so it isn't truncated by 32-bit applications calling mmap64().
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a receive work request has been removed from the queue but has not
had a CQ entry generated for it and the QP is modified to the error
state, the completion entry generated is incorrect. This patch fixes
the problem.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Code was converted from a &= ~mask to clear_bit, but the bit was left
shifted instead of being used directly, so we were either trashing
memory several pages away, or sometimes taking a kernel page fault on
an invalid page.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some types of packet errors are moderately common with longer IB
cables and large clusters, and are not reported with prints by other
IB HCA drivers. This suppresses those messages unless the new
__IPATH_ERRPKTDBG bit is set in ipath_debug. Reporting of temporarily
disabled frequent error interrupts was also made clearer
We also distinguish between chip errors, and bad packets sent or
received in the wording of the messages.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a number of bugs with updating the PSN for retries of
RC requests.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When switching to the QP error state, the completion queue entries
(error or flush) were not being generated correctly.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_dbg doesn't need the same prefixes that printk does.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds support for multiple RDMA reads and atomics to be sent
before an ACK is required to be seen by the requester.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a post send is done in loopback and there is no receive queue
entry, the sending QP is put on a timeout list for a while so the
receiver has a chance to post a receive buffer. If the another post
send is done, the code incorrectly tried to put the QP on the timeout
list again an corrupted the timeout list. This eventually leads to a
spin lock deadlock NMI due to the timer function looping forever with
the lock held.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A silly programming error causes a CQ entry to not be generated if a
SRQ limit event is generated.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A recent change was made to allocate memory for a port after CPU
affinity is set. That change didn't account for subports and was
trying to allocate memory for the port twice.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The chip documentation on the expected TID vs eager TID parity error
bits was reversed from what was implemented in the RTL, for both
chips. This corrects the definitions.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The loop which initializes the user memory region from an array of
pages was using the wrong limit for the array. This worked OK when
dma_map_sg() returned the same number as the number of pages. This
patch fixes the problem.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a sticky state. It is useful for diagnosing problems with
boards versus cable/switch problems.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mthca_arbel_fmr_unmap(), the high bits of the key are masked off.
This gets rid of the effect of adjust_key(), which makes sure that
bits 3 and 23 of the key are equal when the Sinai throughput
optimization is enabled, and so it may happen that an FMR will end up
with bits 3 and 23 in the key being different. This causes data
corruption, because when enabling the throughput optimization, the
driver promises the HCA firmware that bits 3 and 23 of all memory keys
will always be equal.
Fix by re-applying adjust_key() after masking the key.
Thanks to Or Gerlitz for reproducing the problem, and Ariel Shahar for
help in debug.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As of commit 6cdbd77e ("cxgb3 - missing CPL hanler and register
setting."), the cxgb3 ethernet NIC driver no longer handles SET_TCB
replies, so we need to do it in the iWARP driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit c20e20ab ("IB/mthca: Merge MR and FMR space on 64-bit systems")
swapped the number of MTTs and MPTs when initializing the MR table. As
a result, we get a kernel oops when the number of MTT segments
allocated exceeds 0x20000.
Noted by Troy Benjegerdes <troy@scl.ameslab.gov>, and reproduced by
Dotan Barak <dotanb@mellanox.co.il>. This fixes
https://bugs.openfabrics.org/show_bug.cgi?id=490
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This was spotted by the Coverity checker (CID 1554).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eHCA scaling code must not depend on register_cpu_notifier() if
CONFIG_HOTPLUG_CPU is not set, so put all related code into #ifdefs.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix memory region permission problems:
- remove useless and redundant iwch_mem_perms enum.
- create ib_to_tpt_access_rights() for mapping ib access rights
to T3 TPT permissions.
- create ib_to_mwbind_access_rights() for mapping ib access rights
to T3 MWBIND WR permissions.
- fix up the mem reg code to utilize the new functions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only print one AE error for a given connection in the kernel log.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Stop the endpoint timer when the MPA exchange is aborted by the peer.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change iwch_destroy_qp() to always move the QP to ERROR and let
iwch_modify_qp() decide what to do.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes for "normal close" failures:
- Start normal close timer when moving to CLOSING state.
- Handle ABORTING state in close_con_rpl().
- Stop timer correctly on abort during a normal close.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cxgb3 uses dma_alloc_coherent() et al. thus needs linux/dma-mapping.h
include in order to build reliably.
Noticed on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the consumer rejects the connection we end up under-referencing the
endpoint structure. The fix is to call iwch_ep_disconnect() instead
of the low level disconnect functions so that the endpoint close timer
is started correctly.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The garbled logic in mthca_alloc_memfree() causes it to return 0, even
if it fails to allocate all doorbell records. Fix it to return -ENOMEM
when it fails.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes two issues reported by Roland Dreier and Christoph Hellwig:
- Mismatched sync/locking between completion handler and destroy cq We
introduced a counter nr_events per cq to track number of irq events
seen. This counter is incremented when an event queue entry is seen
and decremented after completion handler has been called regardless
if scaling code is active or not. Note that nr_callbacks tracks
number of events assigned to a cpu and both counters can potentially
diverge.
The sync between running completion handler and destroy cq is done
by using the global spin lock ehca_cq_idr_lock.
- Replace yield by wait_event on the counter above to become zero.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Stop the ep timer in ec_status() if the status indicates a
bad close.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- don't mark static functions in C files as inline - gcc should know
best whether inlining makes sense
- never compile the unused cxio_dbg.c
- make the following needlessly global functions static:
- cxio_hal.c: cxio_hal_clear_qp_ctx()
- iwch_provider.c: iwch_get_qp()
- remove the following unused global functions:
- cxio_hal.c: cxio_allocate_stag()
- cxio_resource.: cxio_hal_get_rhdl()
- cxio_resource.: cxio_hal_put_rhdl()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes the needlessly global functions mthca_tavor_write_mtt_seg()
and mthca_arbel_write_mtt_seg() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Remove the Open Grid Computing copyright. It shouldn't be there.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For T3B devices, mark user QP in error once we transition
to TERMINATE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the port phys state as returned from ehca_query_port() to LINK_UP.
ehca actually represents a logical HCA, whose phys/link state always
is LINK_UP.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow users to en/disable scaling code when loading ib_ehca module,
rather than requiring the module to be rebuilt to change the setting.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
