Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since struct hw_key_entry is 32-bytes large and is smaller than
CSR cache size (which is 64-bytes large) we can use the standard
rt2x00usb_register_multiwrite() helper to set key entries.
This cleanup is a part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bit tested by hardware is TXD_W3_WIV and its value
equals the negated value of ENTRY_TXD_ENCRYPT_IV bit.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Registers used for indirect BBP and RF registers access are
respectively BBPCSR and RFCSR, also make it clear that all CSR
registers access goes through rt2x00pci_register_[read,write]()
methods.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on rt2800usb patch from Benoit PAPILLAULT
(commit 1761631083).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver should write the read request into RF_CSR_CFG register
and not BBP_CSR_CFG one in rt2800usb_rfcsr_read().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document known issues with the driver to aid distribution makers,
users and developers in making informed decisions instead of wasting
their time needlessly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document known issues with the driver to aid distribution makers,
users and developers in making informed decisions instead of wasting
their time needlessly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have a TODO item to make all station
management dependent on virtual interfaces, I
figured I'd start with pushing such a change
to drivers before more drivers start using the
ieee80211_find_sta() API with a hw pointer and
cause us grief later on.
For now continue exporting the old API in form
of ieee80211_find_sta_by_hw(), but discourage
its use strongly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Map BAR0 as well, as we need to write to it during init on some chips.
Also, if BAR0 is a 64bit BAR, the register BAR becomes BAR2, so try
mapping BAR2 if mapping BAR1 fails.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving a frame, report the antenna info, long/short preamble
status, 20/40 MHz flag, long/short guard interval status, MCS/legacy
rate status, and MCS/legacy rate index to the stack.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since each firmware block takes on the order of several hundred usec
to upload to the hardware, using msleep in the inner loop would make
the firmware loading process take a lot more time than just doing
busy-waiting like we do now. But if we keep the busy-waiting, we can
at least add a cond_resched() to the inner loop so that we give other
tasks a chance to run while the firmware is being loaded.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there is no STA interface configured, clear the hardware MAC
address to prevent ACKing frames sent to our MAC address.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When FIF_BCN_PRBRESP_PROMISC is not set, we enable the hardware's BSS
filter so that we'll only see packets destined for our BSS. But if no
STA interfaces have been configured, we would end up passing the BSSID
00:00:00:00:00:00 into the POST_SCAN command, which actually disables
the hardware's BSS filter, as it's not a valid BSSID.
Fix this by passing in 01:00:00:00:00:00 instead (the criterion is
that the OUI part of the BSSID must be nonzero), and add comments to
explain what PRE_SCAN and POST_SCAN do.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k's ->prepare_multicast() currently just enables reception of
all multicast packets, which is somewhat ineffective.
Fix this by either disabling all multicast RX, enabling multicast
RX according to the multicast address filter table, or enabling all
multicast RX, depending on whether ->prepare_multicast() was given
any multicast addresses and whether the hardware multicast address
filter table is large enough to fit all requested addresses.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Minor changes to the transmit quiescing logic:
- Clarify the locking rules for ->tx_wait: only the holder of fw_mutex
can wait for the TX path to become idle, but tx_wait itself is read
and cleared by the TX reclaim tasklet under tx_lock.
- Inline mwl8k_txq_busy() in its callers.
- There's no need to kick the transmitter again in
mwl8k_tx_wait_empty(), since it will have been kicked when the
packets currently in the TX ring were added to it.
- If the TX ring didn't drain in time, run mwl8k_scan_tx_ring() after
reading priv->pending_pkts without dropping tx_lock in between.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The GET_STAT command doesn't have an 'action' field like other
commands do, so remove it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271_main.c:(.text+0x271052): undefined reference to `unregister_inetaddr_notifier'
wl1271_main.c:(.text+0x2714d7): undefined reference to `register_inetaddr_notifier'
Driver is doing some filtering based on IP addresses...
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Responses to firmware commands are read in by the command transmission
function, as part of command flow. Previously responses were read in
multiple places.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct the endianness-handling of the firmware command result status handling
code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PSM entries can fail (transmitting the corresponding null-func may not
be heard by the AP.) Previously, this scenario was not detected, and
out-of-sync between STA and AP could occur.
Add retry implementation for the entries to recover from the situation.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the result code of all commands, and return an error code if the
firmware reports an error in execution. Previously this error would go
ignored in most cases.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, to avoid distortions, the TX power level has been hardcoded
to a low value. The value is slightly too low for good functionality, so
we increase it from 7dB to 12dB.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The null-data template (nullfunc) is dependent on the BSSID of the
current AP only, so it needs to be updated only when the BSSID changes.
Removed excess setting of the template.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report successful transmissions (receiver awake and on the same
channel) by generating ACK frames on the hwsim0 interface. This makes
it easier to figure out from packet capture logs whether frames were
delivered or not.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Track the idle state for hwsim radios and reject TX if mac80211 is
trying to transmit something when the radio is supposed to be idle. In
addition, do not deliver frames if the receiving radio is in the idle
state.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
James Grossmann [1] reported that p54 spews out confusing
messages instead of preventing the mayhem from happening.
the reason is that "p54: generate channel list dynamically"
is not perfect. It didn't discard incomplete channel data
sets and therefore p54 advertised to support them as well.
[1]: http://marc.info/?l=linux-wireless&m=125699830215890
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: James Grossmann <cctsurf@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x50 series, it is wimax/wifi combo device, so driver need to enable
the wimax/wifi co-exist function and send the coexist event priority
table to uCode for operation.
The priority table will be used by uCode to determine what is the proper
action it should take when co-exist with WiMAX.
For example, when WiFi runs a scan, it must own radio exclusively, therefore
will disconnect WiMAX if WiMAX is connected.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spatial Multiplexing Power Save was disabled to achieve better
throughput while in power save mode by activating all the rx chains all the time.
By doing so, the device power consumption is high.
Enable static/dynamic spatial multiplexing power save if device support
it, which can lower the power consumption without impact throughput.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add data structure define for COEX_MEDIUM_NOTIFICATION and
COEX_EVENT_CMD host commands.
COEX_MEDIUM_NOTIFICATION is notification from uCode to host to indicate
medium changes. COEX_EVENT_CMD is from host to uCode for coex event
request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
More information than the "-EIO" return code will be useful here.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
