Commit Graph

1426 Commits

Author SHA1 Message Date
Ben Dooks
37e5ffa3f1 [MTD] [NAND] S3C2410 Allow ECC disable to be specified by the board
Add support to disable ECC checking for a given chip
when passed by the board via the platform data.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22 21:41:32 +01:00
Ben Dooks
1c21ab67b7 [MTD] [NAND] S3C2410 Allow ECC layout to be passed through platform data
Add support for the ECC layout to be passed via the
platform data specified by the board.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22 21:41:19 +01:00
Ben Dooks
c45c6c6833 [MTD] [NAND] S3C2410 Allow unset ecc to be ignored for ecc correction
If a block's ecc field is all 0xff, then ignore the ECC
correction. This is for systems where some of the blocks,
such as the initial cramfs are written without ECC and
need to be loaded on start.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22 21:41:03 +01:00
eric miao
fe69af002e [MTD] [NAND] support for pxa3xx
This is preliminary since:

1. It supports only _one_ chip select at the moment. As there is no
   existing platforms available using two chip selects of the NAND
   controller, it shall really not include code for supporting the
   2nd chip select for now, as such code cannot be verified.

2. It resorts to the default and simpliest memory based badblock
   table

3. Only limited types of nand flash are currently supported. Most
   PXA3xx processors come with on-chip NAND flash dies, so there
   isn't much flexibility for other types of NAND.

4. The NAND controller should be configured to detect the device's
   ID, thus making it difficult to use nand_scan_ident() to assist
   the detection process (though it's not impossible)

TODO: fix all the above limitations of cuz :-)

Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22 19:27:27 +01:00
Linus Torvalds
135cedad74 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (26 commits)
  mmc: sdio_ops.c should #include "sdio_ops.h"
  mmc: proper prototypes for mmc_attach_*()
  mmc: make __mmc_release_bus() static
  sdhci: improve no card, no reset quirk
  MMC: OMAP: Do not busy wait for end of command for ever
  MMC: OMAP: Start new commands from work queue instead of irq
  MMC: OMAP: Lazy clock shutdown
  MMC: OMAP: Move failing command abortion to workqueue
  MMC: OMAP: Use tasklet instead of workqueue for cover switch notification
  MMC: OMAP: Check the get_cover_state function pointer if not set
  MMC: OMAP: Using setup_timer instead of init_timer
  MMC: OMAP: Abort stuck commands
  MMC: OMAP: General cleanup for MMC multislot support
  MMC: OMAP: Power functions modified to MMC multislot support
  MMC: OMAP: Fix timeout calculation for MMC multislot support
  MMC: OMAP: New release dma and abort xfer functions
  MMC: OMAP: Add back cover switch support
  MMC: OMAP: Introduce new multislot structure and change driver to use it
  MMC: OMAP: Remove cover switch handling to allow adding multislot support
  MMC: OMAP: Fix the BYTEBLOCK capability removal
  ...
2008-04-21 17:23:30 -07:00
Linus Torvalds
e9b62693ae Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/juhl/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/juhl/trivial: (24 commits)
  DOC:  A couple corrections and clarifications in USB doc.
  Generate a slightly more informative error msg for bad HZ
  fix typo "is" -> "if" in Makefile
  ext*: spelling fix prefered -> preferred
  DOCUMENTATION:  Use newer DEFINE_SPINLOCK macro in docs.
  KEYS:  Fix the comment to match the file name in rxrpc-type.h.
  RAID: remove trailing space from printk line
  DMA engine: typo fixes
  Remove unused MAX_NODES_SHIFT
  MAINTAINERS: Clarify access to OCFS2 development mailing list.
  V4L: Storage class should be before const qualifier (sn9c102)
  V4L: Storage class should be before const qualifier
  sonypi: Storage class should be before const qualifier
  intel_menlow: Storage class should be before const qualifier
  DVB: Storage class should be before const qualifier
  arm: Storage class should be before const qualifier
  ALSA: Storage class should be before const qualifier
  acpi: Storage class should be before const qualifier
  firmware_sample_driver.c: fix coding style
  MAINTAINERS: Add ati_remote2 driver
  ...

Fixed up trivial conflicts in firmware_sample_driver.c
2008-04-21 16:36:46 -07:00
Tobias Klauser
b1d18dc06b arm: Storage class should be before const qualifier
The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
2008-04-21 22:26:40 +00:00
Russell King
cf816ecb53 Merge branch 'merge-fixes' into devel 2008-04-19 17:17:34 +01:00
Russell King
adf6d34e46 Merge branch 'omap2-upstream' into devel 2008-04-19 17:17:29 +01:00
Russell King
d1964dab60 Merge branches 'arm', 'at91', 'ep93xx', 'iop', 'ks8695', 'misc', 'mxc', 'ns9x', 'orion', 'pxa', 'sa1100', 's3c' and 'sparsemem' into devel 2008-04-19 17:17:25 +01:00
Guennadi Liakhovetski
3f3acefb63 [ARM] pxa: V4L2 soc_camera driver for PXA270
This patch adds a driver for the Quick Capture Interface on the PXA270.
It is based on the original driver from Intel, but has been re-worked
multiple times since then, now it also supports the V4L2 API.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 17:14:30 +01:00
Ryan Mallon
b685004f8d [ARM] 4988/1: Add GPIO lib support to the EP93xx
Adds support for the generic GPIO lib to the EP93xx family. The gpio
handling code has been moved from core.c to a new file called gpio.c.
The GPIO based IRQ code has not been changed.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 14:01:43 +01:00
Russell King
05944d74bc [ARM] Add initial sparsemem support
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:36:48 +01:00
Dmitry Baryshkov
c546106cc1 [ARM] 5002/1: tosa: add two more leds
This adds support for two more leds:
the wlan one (found in SL-6000W and SL-6000L) and
the blutooth one (found in SL-6000W).

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:09 +01:00
Dmitry Baryshkov
ba4eb7e60b [ARM] 5004/1: Tosa: make several unreferenced structures static.
Now that scoop gpio's are converted to generic_gpio,
tosascoop_device and tosascoop_jc_device don't have
to be exported.

Also make tosa_gpio_* static

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:09 +01:00
Mark Brown
768dec4cc3 [ARM] 4976/1: zylonite: Configure GPIO for WM9713 IRQ line
Set up the IRQ line for the WM9713 device on the Zylonite.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:09 +01:00
Dmitry Baryshkov
311c736c19 [ARM] 4973/1: Tosa: use leds-gpio driver.
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-tosa.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:08 +01:00
Dmitry Baryshkov
d4e7d09f7a [ARM] 4972/1: Tosa: convert scoop GPIOs usage to generic gpio code
Convert set/reset_scoop_gpio to generic gpio calls.
This patch depends on the pxaficp_ir hooks patch.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:08 +01:00
Dmitry Baryshkov
baf1c5d2a0 [ARM] 4971/1: pxaficp_ir: provide startup and shutdown hooks
Let platform do some specific initialisation and cleanup
things during pxaficp_ir probing and removing. E.g. this
can be usefull to request/free gpios used by the platform
to control the transceiver.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:08 +01:00
Mike Rapoport
64c1dd3bbf [ARM] 4959/1: PXA: Fix misprint in CICR1_RGBT_CONV
This patch fixes misprint in definition of CICR1_RGBT_CONV in include/asm-arm/arch-pxa/pxa-regs.h

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:07 +01:00
Philipp Zabel
e07ff8d809 [ARM] 4952/1: magician: add LCD detection, LCD power switching, update pxafb settings
All magician devices I've encountered so far have featured the Toppoly
TD028STEB1 display, so the Samsung LTP280QV support is untested.
The power-on sequence is not correct because pxafb doesn't yet support
enabling the LCD controller in the middle of the it.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:07 +01:00
Philipp Zabel
70e357f842 [ARM] 4948/1: magician: use htc-egpio to drive the GPIO/IRQ expander CPLD
needed for power management (audio, BT, charging, GSM, LCD, SD), GSM, flash and SD operation and audio routing.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:07 +01:00
Philipp Zabel
103a175489 [ARM] 4943/2: magician: fix magician.h GPIO header includes
PXA GPIO definitions were split from pxa-regs.h into pxa2xx-gpio.h.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:06 +01:00
Jaya Kumar
90b8fc3496 [ARM] 4867/1: Adds flash, udc, mci support for gumstix F boards
This patch implements support for Gumstix-F flash, udc and mci. Fixes since the last time are:
- Steve Sakoman as maintainer
- cleanup for udc and mci setup

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:06 +01:00
eric miao
4354e18812 [ARM] pxa: remove keypad register definitions from pxa-regs.h
Keypad registers are now fully defined within pxa27x-keypad.c, no
need to keep those definitions in pxa-regs.h

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:06 +01:00
eric miao
3732098041 [ARM] pxa: add pxa27x_keypad device and pxa_set_keypad_info()
also update the clk definitions in pxa27x and pxa3xx.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:05 +01:00
eric miao
c0a596d6a1 [ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x}
Changes include:

1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
   the board capability of this pin to wakeup the system

2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
   enable/disable wakeup from GPIOs and keypad GPIO

   * these functions are currently kept in mfp-pxa2xx.c due to their
     dependency to the MFP configuration

3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
   is set on incorrect pins

So that the GPIO's wakeup capability is now decided by the following:

   a) processor's capability: (only those GPIOs which have dedicated
      bits within PWER/PRER/PFER can wakeup the system), this is
      initialized by pxa{25x,27x}_init_mfp()

   b) board design decides:
      - whether the pin is designed to wakeup the system (some of
        the GPIOs are configured as other functions, which is not
        intended to be a wakeup source), by OR'ing the pin config
        with MFP_LPM_CAN_WAKEUP

      - which edge the pin is designed to wakeup the system, this
        may depends on external peripherals/connections, which is
        totally board specific; this is indicated by MFP_LPM_EDGE_*

   c) the corresponding device's (most likely the gpio_keys.c) wakeup
      attribute:

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:05 +01:00
eric miao
7facc2f937 [ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs.  A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.

A pin configuration on pxa{25x,27x} is composed of:

    - alternate function selection (or pin mux as commonly called)
    - low power state or sleep state
    - wakeup enabling from low power mode

The following MFP_xxx bit definitions in mfp.h are re-used:

    - MFP_PIN(x)
    - MFP_AFx
    - MFP_LPM_DRIVE_{LOW, HIGH}
    - MFP_LPM_EDGE_*

Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:

    - MFP_CFG_IN  : for input alternate functions
    - MFP_CFG_OUT : for output alternate functions

Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT().  As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.

Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output.  The actual
direction of the GPIO is configured by gpio_direction_{input, output}

Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.

E.g.  invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:

    enable_irq_wake( gpio_to_irq(35) );

To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).

Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:

    - MFP_LPM_WAKEUP_ENABLE

The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:

    - WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
    - WAKEUP_ON_LEVEL_HIGH

The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.

These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.

The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:04 +01:00
eric miao
a683b14df8 [ARM] pxa: separate GPIOs and their mode definitions to pxa2xx-gpio.h
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
   of the PXA register definitions

2. this is actually a temporary move in the transition of PXA2xx to
   use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
   code will still work and new code can be added in step by step

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:04 +01:00
eric miao
f6fb7af476 [ARM] pxa: integrate low IRQ chip (ICIP) and high IRQ chip (ICIP2) into one
This makes the code better organized and simplified a bit.  The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.

This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable.  The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)

The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).

"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:04 +01:00
Robert Jarzmik
d72b1370b0 [ARM] 4868/1: Enhance pxa270 GPIO definitions
Enhanced GPIO alternate functions descriptions,
taken from Intel PXA270 Developers Manual.

Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:03 +01:00
Mark Brown
dcc88a170c [ARM] 4830/1: Add support for the CLK_POUT pin on PXA3xx CPUs
Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:02 +01:00
Uwe Kleine-König
cbfc0f0406 [ARM] 4852/1: Add timerfd_create, timerfd_settime and timerfd_gettime syscall entries
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:28:06 +01:00
Catalin Marinas
14a6acc23f RealView: Add uncompressing support for PB1176
This patch adds the UART0 base address detection in uncompress.h.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:16 +01:00
Bahadir Balban
a0316b244e RealView: Base support for the PB1176 platform
This patch adds the base files for the PB1176 platform support.

Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:15 +01:00
Catalin Marinas
34401ec466 RealView: Add uncompressing support to PB11MPCore
This patch adds the UART address detection in uncompress.h for the
PB11MPCore platform.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:13 +01:00
Bahadir Balban
a9b67db504 RealView: Base support for the PB11MPCore platform
This patch adds the base files for the PB11MPCore platform support.

Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:13 +01:00
Catalin Marinas
51faf9b5c0 RealView: Change the IO_ADDRESS macro
This patch changes the IO_ADDRESS macro for the RealView platforms to
accomodate a wider range of physical addresses on PB11MPCore.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:12 +01:00
Catalin Marinas
393538e6d2 RealView: Move more device address definitions to board-eb.h
The upcoming PB11MPCore and PB1176 have different memory maps and some
of the definitions in platform.h are no longer common. This patch
moves them to the board-eb.h file and updates their usage in
realview_eb.c.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:11 +01:00
Catalin Marinas
9a386f0651 RealView: Move the UART definitions to EB specific files
Since the PB1176 has different UART base addresses, this patch moves
the definitions form platorm.h to board-eb.h. It also modifies
uncompress.h to detect the platform type at run-time.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:11 +01:00
Catalin Marinas
80192735e4 RealView: Move the timer definitions into the EB specific files
This patch moves the timer definitions from platform.h into board-eb.h
as they are different on PB11MPCore and PB1176. It also adds
timerX_va_base variables in core.c which are set by the
realview_eb_timer_init function before invoking realview_timer_init.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:11 +01:00
Catalin Marinas
a44ddfd5bf RealView: Move the flash definitions out of platform.h
This patch moves the patch definitions into board-eb.h and
realview_eb.c (from core.c) as they are different on the PB11MPCore
and PB1176 platforms.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:10 +01:00
Catalin Marinas
073b6ff3b9 RealView: Move the EB GIC definitions to the board file
This is in preparation for the RealView PB11MPCore and PB1176 patches
which have different base addresses for the GIC.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:09 +01:00
Catalin Marinas
b7b0ba942f RealView: Move the SCU initialisation out of __v6_setup
This patch moves the SCU initialisation from __v6_setup to the
smp_prepare_cpus() function as it relies on platform-specific
settings. Changes to get_core_count() are mainly for allowing cleaner
code with the upcoming PB11MPCore patches.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:08 +01:00
Paul Brook
48d7927bdf Add a prefetch abort handler
This patch adds a prefetch abort handler similar to the data abort one
and renames the latter for consistency. Initial implementation by Paul
Brook with some renaming by Catalin Marinas.

Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:07 +01:00
Catalin Marinas
d7f864be83 ARMv7: Add support for the ThumbEE state saving/restoring
This patch adds the detection and handling of the ThumbEE extension on
ARMv7 CPUs.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2008-04-18 22:43:06 +01:00
Juha Yrjola
abfbe5f785 MMC: OMAP: Introduce new multislot structure and change driver to use it
Introduce new MMC multislot structure and change driver to use it.

Note that MMC clocking is now enabled in mmc_omap_select_slot()
and disabled in mmc_omap_release_slot().

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:28 +02:00
Linus Torvalds
188da98800 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (58 commits)
  ide: remove ide_init_default_irq() macro
  ide: move default IDE ports setup to ide_generic host driver
  ide: remove obsoleted "idex=noprobe" kernel parameter (take 2)
  ide: remove needless hwif->irq check from ide_hwif_configure()
  ide: init hwif->{io_ports,irq} explicitly in legacy VLB host drivers
  ide: limit legacy VLB host drivers to alpha, x86 and mips
  cmd640: init hwif->{io_ports,irq} explicitly
  cmd640: cleanup setup_device_ptrs()
  ide: add ide-4drives host driver (take 3)
  ide: remove ppc ifdef from init_ide_data()
  ide: remove ide_default_io_ctl() macro
  ide: remove CONFIG_IDE_ARCH_OBSOLETE_INIT
  ide: add CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS (take 2)
  ppc/pmac: remove no longer needed IDE quirk
  ppc: don't include <linux/ide.h>
  ppc: remove ppc_ide_md
  ppc/pplus: remove ppc_ide_md.ide_init_hwif hook
  ppc/sandpoint: remove ppc_ide_md hooks
  ppc/lopec: remove ppc_ide_md hooks
  ppc/mpc8xx: remove ppc_ide_md hooks
  ...
2008-04-18 08:39:24 -07:00
Linus Torvalds
07fe944e87 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  dmaengine: ack to flags: make use of the unused bits in the 'ack' field
  iop-adma: remove the workaround for missed interrupts on iop3xx
  async_tx: kill ->device_dependency_added
  async_tx: fix multiple dependency submission
  fsldma: Split the MPC83xx event from MPC85xx and refine irq codes.
  fsldma: Remove CONFIG_FSL_DMA_SELFTEST, keep fsl_dma_self_test() running always.
2008-04-18 08:38:55 -07:00
Bartlomiej Zolnierkiewicz
9dfcd15a6d ide: remove ide_default_io_ctl() macro
It is always == '((base) + 0x206)' if CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS=y
and it is not needed otherwise (arm, blackfin, parisc, ppc64, sh, sparc[64]).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:34 +02:00