* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2x: Accessing un-mapped page
ath9k: Fix TX control flag use for no ACK and RTS/CTS
ath9k: Fix TX status reporting
iwlwifi: fix STATUS_EXIT_PENDING is not set on pci_remove
iwlwifi: call apm stop on exit
iwlwifi: fix Tx cmd memory allocation failure handling
iwlwifi: fix rx_chain computation
iwlwifi: fix station mimo power save values
iwlwifi: remove false rxon if rx chain changes
iwlwifi: fix hidden ssid discovery in passive channels
iwlwifi: W/A for the TSF correction in IBSS
netxen: Remove workaround for chipset quirk
pcnet-cs, axnet_cs: add new IDs, remove dup ID with less info
ixgbe: initialize interrupt throttle rate
net/usb/pegasus: avoid hundreds of diagnostics
tipc: Don't use structure names which easily globally conflict.
This patch sets STATUS_EXIT_PENDING on pci_remove. Otherwise
iwl4965_down may fail to uninitialize the driver.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch calls apm stop on exit and suspend. Without this patch
hardware consumes power even after driver is removed or suspended.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch "iwlwifi: do not use GFP_DMA in iwl_tx_queue_init" removes
GFP_DMA from allocation tx command buffers. GFP_DMA allows allocation
only for memory under 16M which causes allocation problems
suspend/resume flows.
Using kmalloc is temporal solution and some consistent/coherent
allocation schema will be more correct. Since iwlwifi hardware
supports 64bit address this solution should work on x86 (32 and
64bit) for now.
This patch fixes memory freeing problem in the previous patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes rx_chain computation. The code that adjusts number of
rx chains to number supported by HW was missing. Miss configuration
causes firmware error. Note: iwlwifi supports HW with up to 3 RX
chains (2x2, 2x3, 1x2, and 3x3 MIMO). This patch also simplifies the
whole RX chain computation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the wrong use MIMO power save values. Our TX was
configured with our MIMO power save values instead of peer's MIMO power
save values, this may affect connectivity. The peer STA/AP may not sense
our traffic at all as it doesn't have all RX chains opened.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx chain might change during power save transitions but it doesn't
require sending Full-ROXN command to the firmware. Full-RXON requires
reconnection to an AP and thus affects user experience. The patch
avoids the Full-RXON by removing the rx_chain modification check in
iwl_full_rxon_required function.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables sending of direct probes on passive channels, as long as
traffic was detected on that channel. This enables connectivity to
hidden/non broadcasting SSIDs APs on passive channels. Note 5000 HW
declares all 5.2 spectrum as passive.
Signed-off-by: Cahill Ben <ben.m.cahill@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a W/A for the TSF sync issue in IBSS merging. HW is not
capable to sync TSF (it's constantly little behind). This creates
constant IBSS merging upon reception of each beacon, adding and removing
station which in turn creates above 50% packet loss and thus dramatically
degrade the throughput. The W/A simply stops the driver from declaring it
has a reliable TSF value and thus eliminates IBSS merging.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipsec: Fix deadlock in xfrm_state management.
ipv: Re-enable IP when MTU > 68
net/xfrm: Use an IS_ERR test rather than a NULL test
ath9: Fix ath_rx_flush_tid() for IRQs disabled kernel warning message.
ath9k: Incorrect key used when group and pairwise ciphers are different.
rt2x00: Compiler warning unmasked by fix of BUILD_BUG_ON
mac80211: Fix debugfs union misuse and pointer corruption
wireless/libertas/if_cs.c: fix memory leaks
orinoco: Multicast to the specified addresses
iwlwifi: fix 64bit platform firmware loading
iwlwifi: fix apm_stop (wrong bit polarity for FLAG_INIT_DONE)
iwlwifi: workaround interrupt handling no some platforms
iwlwifi: do not use GFP_DMA in iwl_tx_queue_init
net/wireless/Kconfig: clarify the description for CONFIG_WIRELESS_EXT_SYSFS
net: Unbreak userspace usage of linux/mroute.h
pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock()
ipv6: When we droped a packet, we should return NET_RX_DROP instead of 0
This patch addresses an issue with the locking order. ath_rx_flush_tid()
uses spin_lock/unlock_bh when IRQs are disabled in sta_notify by mac80211.
As node clean up is still pending with ath9k and this problematic portion
of the code is expected to change anyway, thinking of a proper fix may not
be worthwhile. So having this interim fix helps the users to get rid of the
kernel warning message.
Pasted the kernel warning message for reference.
kernel: ath0: No ProbeResp from current AP 00:1b:11:60:7a:3d - assume out of range
kernel: ------------[ cut here ]------------
kernel: WARNING: at kernel/softirq.c:136 local_bh_enable+0x3c/0xab()
kernel: Pid: 1029, comm: ath9k Not tainted 2.6.27-rc4-wt-w1fi-wl
kernel:
kernel: Call Trace:
kernel: [<ffffffff802278d8>] warn_on_slowpath+0x51/0x77
kernel: [<ffffffff80224c51>] check_preempt_wakeup+0xf3/0x123
kernel: [<ffffffff80239658>] autoremove_wake_function+0x9/0x2e
kernel: [<ffffffff8022c281>] local_bh_enable+0x3c/0xab
kernel: [<ffffffffa01ab75a>] ath_rx_node_cleanup+0x38/0x6e [ath9k]
kernel: [<ffffffffa01b2280>] ath_node_detach+0x3b/0xb6 [ath9k]
kernel: [<ffffffffa01ab09f>] ath9k_sta_notify+0x12b/0x165 [ath9k]
kernel: [<ffffffff802366cf>] queue_work+0x1d/0x49
kernel: [<ffffffffa018c3fc>] add_todo+0x70/0x99 [mac80211]
kernel: [<ffffffffa017de76>] __sta_info_unlink+0x16b/0x19e [mac80211]
kernel: [<ffffffffa017e6ed>] sta_info_unlink+0x18/0x43 [mac80211]
kernel: [<ffffffffa0182732>] ieee80211_associated+0xaa/0x16d [mac80211]
kernel: [<ffffffffa0184a1a>] ieee80211_sta_work+0x4fb/0x6b4 [mac80211]
kernel: [<ffffffff80469c58>] thread_return+0x30/0xa9
kernel: [<ffffffffa018451f>] ieee80211_sta_work+0x0/0x6b4 [mac80211]
kernel: [<ffffffff802362c2>] run_workqueue+0xb1/0x17a
kernel: [<ffffffff80236be9>] worker_thread+0xd0/0xdb
kernel: [<ffffffff8023964f>] autoremove_wake_function+0x0/0x2e
kernel: [<ffffffff80236b19>] worker_thread+0x0/0xdb
kernel: [<ffffffff8023954a>] kthread+0x47/0x75
kernel: [<ffffffff80223121>] schedule_tail+0x18/0x50
kernel: [<ffffffff8020bc49>] child_rip+0xa/0x11
kernel: [<ffffffff80239503>] kthread+0x0/0x75
kernel: [<ffffffff8020bc3f>] child_rip+0x0/0x11
kernel:
kernel: ---[ end trace e9bb5da661055827 ]---
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updating sc_keytype multiple times when groupwise and pairwise
ciphers are different results in incorrect pairwise key type
assumed for TX control and normal ping fails. This works fine
for cases where both groupwise and pairwise ciphers are same.
Also use mac80211 provided enums for key length calculation.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A "Set" to a sign-bit in an "&" operation causes a compiler warning.
Make calculations unsigned.
[ The warning was masked by the old definition of BUILD_BUG_ON() ]
Also remove __builtin_constant_p from FIELD_CHECK since BUILD_BUG_ON
no longer permits non-const values.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The leak in if_cs_prog_helper() is obvious.
It looks a bit as if not freeing "fw" in if_cs_prog_real() was done
intentionally, but I'm not seeing why it shouldn't be freed.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multicasting the driver sets the number of group addresses using
the count from the previous set multicast command. In general this means
you have to set the multicast addresses twice to get the behaviour you
want.
If we were multicasting, and reduce the number of addresses we are
multicasting to, then the driver would write uninitialised data from the
stack into the group addresses to multicast to.
Only write the multicast addresses we have specifically set.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes loading firmware from memory above 32bit.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Marcel Holtmann <holtmann@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes CSR_GP_CNTRL_REG_FLAG_INIT_DONE was set instead of
cleared which disabled moving device to D0U state.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds workaround for an interrupt related hardware bug on
some platforms. (Apparently these platforms boot-up w/ INTX_DISABLED
set. -- JWL)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GFP_DMA is not necessary for the iwlwifi hardware and it can cause
allocation failures and/or invoke the OOM killer on lots of systems.
For reference:
https://bugzilla.redhat.com/show_bug.cgi?id=459709
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bintval is set to the initial value at .config_interface which is too
late, since it overwrites previously set value from .config. Move the
initialization to the .add_interface.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacons setup and config was racy with beacon send. Ensure that
ISR and reset functions see consistent state of bbuf.
Use also dev_kfree_skb_any in ath5k_txbuf_free since we call it
from atomic now.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the AP rejects a Shared Key authentication request, try Open System
auth too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return errors from request_firmware() (like other drivers that do
firmware load on device open) and make up plausible codes for other
error conditions. Gives userspace tools like NetworkManager a clue that
firmware may be missing when the result of setting IFF_UP is ENOENT.
Signed-off-by: Dan Williams <dcbw@redhat.com>
v2: fix reversed check of atmel_wakeup_firmware() in probe_atmel_card()
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/ath5k/base.c
drivers/net/wireless/b43/main.c
drivers/net/wireless/ipw2100.c
drivers/net/wireless/ipw2200.c
drivers/net/wireless/iwlwifi/iwl-3945.c
drivers/net/wireless/iwlwifi/iwl-4965.c
drivers/net/wireless/iwlwifi/iwl-5000.c
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/iwlwifi/iwl-eeprom.c
drivers/net/wireless/iwlwifi/iwl-hcmd.c
drivers/net/wireless/iwlwifi/iwl-power.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txdone_entry_desc_flags is used with __set_bit and test_bit which
bit-shift the values, so don't bit-shift the flags in the enum.
Also make sure flags are initialized before being used.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In trying to help users on the Ubuntu Bugzilla, I discovered another
BCM4306 with the Bluetooth Coexistence programming error in the SPROM.
This patch is contingent on the one that added the Linksys device with
subdevice code of 0x0014.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Only important for USB V1 Adaptors)
If an incoming frame wasn't accepted by p54_rx function
the skb will be reused for new frames...
But, we must not forget to set the skb's data pointers into
the same state in which it was initialized by p54u_init_urbs.
Otherwise we either end up with 16 bytes less on every requeue,
or if a new frame is worthy enough to be accepted, the data is
in the wrong place (urb->transfer_buffer wasn't updated!) and mac80211
has a hard time to recognize it...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->tx_hdr_len is set by the driver _after_ it called p54_init_common.
While this isn't much a problem for any PCI or ISL3887 cards/sticks,
because they don't need any extra header and therefore tx_hdr_len is
zero for them...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add newlines at printk outputs to not break dmesg.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB ID for a Netgear WG111v3.
Signed-off-by: matthieu Barthélemy <bonsouere@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Linksys WMP54G (BCM4306/3) card in a PCI format has an SPROM coding
error and needs the fix found for several other cards.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 256b152b00 (ath5k: don't enable
MSI, we cannot handle it yet) has removed msi support, but overlooked
the suspend/resume code. This patch completes msi removal.
I don't consider this patch copyrightable, and thus put it into the
public domain. The result is of course a base.c file dual-licensed under
3-clause-BSD and GPL.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit b19fa1f, entitled "net: Delete NETDEVICES_MULTIQUEUE kconfig
option" breaks p54pci and p54usb.
Additionally, the old logic always tx'ed cts frames (if enabled)
with a short preamble when [rate > 3]. (i.e. with any 802.11g rate).
Of course this isn't that bad, but it's still wrong!
(This patch also clarifies the meanings of some of the fields in the tx
header for the hardware. -- JWL)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(I missed the fact that the original post said to apply this patch
twice... -- JWL)
Original commit log message:
This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.
Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a single enum for managing modes, store supported modes by
the HW in a bitmask.
Register legacy rates with mac80211 only at init.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ath9k_tx_queue_info which contains the same elements,
and merge get/set functions of tx queue properties.
Also, fix whitespace damage in struct ath_softc.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.
Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new mac80211 11n ath9k Atheros driver. Only STA support
is currently enabled and tested.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove Atheros 11n devices from being claimed by ath5k as its
now handled by ath9k.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these "magic" values must to be the other way round...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible for unsupported operating modes
to be accepted by the add_interface callback function.
This patch will block those modes until proper support
has been implemented for them.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
