Xceive has graciously allowed us to now freely redistribute the xc5000
firmware, which eliminates the need for users to manually extract the blob
from the Hauppauge driver.
Thanks to Brian Mathews <bmathews@xceive.com> for providing this code
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the xc5000 spec, the reset pin only needs to be held low for 10ms.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a typo in the module description for the "no_poweroff" option, where the
help was being associated with the "debug" option instead.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Defer loading of the xc5000 firmware until it is actually needed. This helps
on distros that have hald, which results in the device not being available
for use for around ten seconds in cases where the i2c bus is slow (such as
the HVR-950Q). Also, the firmware load isn't really useful since we
immediately put the device to sleep afterward, which means a firmware reload
will be required anyway.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide for the ability for a user to disable putting the tuner to sleep, in
case he doesn't want to incur the cost of reloading the firmware when starting
up his/her application. The module options are intentionally identical to
xc3028.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it a little more obvious in the dmesg output what is going on during
firmware upload. This is more important for boards like the HVR-950q that
take nearly seven seconds to do the upload.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Starting in firmware version 1.1.44, Xceive recommends using the FINERFREQ for
all normal tuning (the doc indicates reg 0x03 should only be used for fast
scanning for channel lock)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Expose the firmware build number along with the other version info
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc5000 datasheet indicates that the reset pin only needs to be held low
for 10ms. Reduce the value accordingly, which speeds up the firmware load
time a bit.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xceive got rid of the XREG_POWER_DOWN register in later firmware revisions.
Their technical support informed me that the correct way to put the tuner
to sleep is to pull the reset pin (but don't reload the firmware).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This switches to a new version of the xc5000 firmware, extracted from the
latest Hauppauge driver. It includes the support for the XREG_BUSY register
(a lack of which was causing tuning to take 3200ms instead of around 300ms).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't sleep for 400ms polling the tuner's lock if in digital mode (since the
xc5000 lock status registers appear to only be reliable in analog mode)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bring back the code that puts the xc5000 to sleep. For the Pinnacle 801e
this results in power consumption at idle dropping from 325ma to 124ma.
If there are *actually* any devices that don't work in this configuration,
they should set dvb_frontend.ops.tuner_ops.sleep to NULL (per mkrufky's
suggestion)
Also, had to make sure we were making sure the firmware was loaded in the
digital version of set_params, or else we end up get i2c errors if the
device is asleep
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make return value checking for calls to i2c routines explicit.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup the i2c write routine, getting rid of a passthrough function with only
one caller
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch centralizes the i2c read functions, and eliminates pass-through
function only called by one caller.
Make reading of xc5000 registers an atomic i2c transaction in case we're on a
multi-master bus.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch means the board will be recognised, and the parts brought
out of reset correctly. This patches depends on the centralized GPIO
patch to be merged. What's missing before the HVR-1270 will function
for DTV? The model# needs to be added to avoid 'unknown model'
output and the LG3305/Tuner need to be attached in cx23885-dvb.c
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The GPIO's on the product can be in one of three places. To date we've
mainly used the GPIO's on the bridge itself, and once on the encoder.
Rather than having the complexity of multiple GPIO writes/reads from
isolated placed in the driver we'll route them through this function,
so we can make intelligent decisions about 1) Where the GPIO lives
and 2) Whether it conflicts (based on board) with some other function
to avoid bugs.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
av7110_av_start_play() should return 0 on success.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Discard PES packet if transport error indicator flag is set.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implemented TS replay capability.
audio/video devices are able to process PES and TS data now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Build fails when CONFIG_I2C=n, so handle that case in the if block:
drivers/built-in.o: In function `v4l2_device_unregister':
(.text+0x157821): undefined reference to `i2c_unregister_device'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
... else DVB-T tuning will not work.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, DVB-T is broken and this fixes it.
The PVRUSB2 has an odd I2C bus configuration where opening the i2c gate
on the digital and analog demod causes the tuner to fail. This needs
to be protected against for the PVRUSB2.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The TCL MNM05-04 is used on some HVR-1600 models. It appears to be
similar to the TCL MFMN05-4 but without FM radio. The
TUNER_PHILIPS_FM1236_MK3 tuner definition appears to be the proper existing
tuner definition to use for this tuner.
Reported-by: Matt Beadon <matt.beadon@gmail.com>
Tested-by: Matt Beadon <matt.beadon@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c core used to maintain a list of client for each adapter. This
is a duplication of what the driver core already does, so this list
will be removed as part of a future cleanup. Anyone using this list
must stop doing so.
For pvrusb2, I propose the following change, which should lead to an
equally informative output. The only difference is that i2c clients
which are not a v4l2 subdev won't show up, but I guess this case is
not supposed to happen anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kick up the pvrusb2 version number advertised through the v4l
interface. This value really has almost no meaning because I don't
make a serious attempt to version the driver in this manner (otherwise
this one line becomes a nasty hotspot of changes and merge
conflicts). The value that is here is really a historical thing.
However Hans Verkuil thought it might be a good idea to bump up the
number anyway right now since the driver's mechanism for communicating
with the v4l core has pretty much completely changed. Sending out a
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sets the disable_autoload_ir_video module option to being set,
which disables any attempt by the driver to autoload IR support. This
changes preserves previous behavior, for now. This change can be set
back concurrent with other changes that finally update i2c-kbd-i2c to
use the new i2c binding model.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir-kbd-i2c module is about to be updated to match the new style
i2c binding model. These pvrusb2 changes maintain compatibility with
that change. Note that this does not actually break anything even
without the expected ir-kbd-i2c changes yet because previously the
pvrusb2 didn't autoload ir-kbd-i2c anyway.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change defines all possible "IR schemes" related to the pvrusb2
driver, on a per-device basis. That information is then set according
to the hardware in use. The idea here is to make possible a more
intelligent future decision on which, if any, IR receiver driver might
be loaded during initialization.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ADV7343 I2C based video encoder driver. This follows the
v4l2-subdev framework. This driver has been tested on TI DM646x EVM. It
has been tested for Composite and Component outputs.
Updates as per review by Mauro Chehab, added support for more standards
supported by the encoder. Also adding the missed out signed-offs.Tested
only NTSC and PAL standards.
[hverkuil@xs4all.nl: s_routing API changed, updated driver to use new API]
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds driver for TI THS7303 video amplifier. This driver is
implemented as a v4l2 sub device. Tested on TI DM646x EVM.
This version has updates based on review comments by Mauro Chehab.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new i2c binding model doesn't use i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2 ioctls usually return 0 when the operation was successful
and -1 in case of error. Currently VIDIOC_REQBUFS returns the
number of buffers which is redundant because this information is
available in count field of struct v4l2_requestbuffers. The
V4L2 API specification, revision 0.24 [1] explicitly specifies for
VIDIOC_REQBUFS that the return value shall be 0 on success.
The patch was tested with v4l-test 0.13 [2] with vivi driver.
References:
[1] V4L2 API specification, revision 0.24
http://v4l2spec.bytesex.org/spec/r13696.htm
[2] v4l-test: Test environment for Video For Linux Two API
http://v4l-test.sourceforge.net/
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support to the remote control of the Winfast TV2000 XP Global TV
capture card. A case statement was added in order to initialize the
GPIO data structures as well as a case statement for handling the keys
correctly when pressed.
Thanks to Hermann and Mauro for all the help
Signed-off-by: Pieter C van Schaik <vansterpc@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When we capture signal from composite input offen lost and found syncro
sequence. In this case the MPEG coder hardware reset after each
lost/found event. The image has a lot of artefactes. This patch remove
hardware reset of MPEG encoder.
This is patch from our customer. I checked this.
With my best regards, Dmitry.
Signed-off-by: Alexey Osipov <lion-simba@pridelands.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If video has a lot of changes in frame, MPEG encoder need more time for
coding process. Add new bigger timeout for encoder.
This is patch from our customer. I checked this.
Signed-off-by: Alexey Osipov <lion-simba@pridelands.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Compro VideoMate T750 has no support for IR and DVB-T yet.
Disable both to avoid fall through and confusing printouts.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the videobuf-dma-contig sync operation. Sync is only needed
for noncoherent buffers, and since videobuf-dma-contig is built on
coherent memory allocators the memory is by definition always in sync.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the physical device rather than the i2c adapter as the reference
device when loading firmwares. This will prevent the sysfs name
collision with i2c-dev that has been reported many times.
I may have missed other drivers which need the same fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The number of packets per isochronous message may now be set by the subdrivers
(default value 32).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new mechanism does not use any temporary buffer.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A new image may start without any UVC EOF in the last packet of the
previous image.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the bandwidth is not wide enough, the transfer endpoint may be set to
the one of the alternate setting 0. This one may be null and this causes a
divide by 0 oops.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let the subdrivers to set the 'image transfer by bulk' flag.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a platform driver to soc_camera.c. This way we preserve backwards
compatibility with existing platforms and can start converting them one by one
to the new platform-device soc-camera interface.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure the variable gain amplifier gain for SIF is driven by the audio deocder
and not the video decoder. This forced rework of the analog front end (AFE)
configuration to not rely on autoconfiguration, but instead set up the AFE mux,
AFE parameters, and ADC1 & ADC2 configurations explicitly.
Reported-by: Helen Buus <mythtv@hbuus.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set the analog gain at sensor init. Also set a sensible default value.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the possibility to control the exposure on the vv6410 sensor
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ASUS A6K needs the vflip quirk. Thanks to Marco Baldo for reporting
the issue.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that the hflip and vflip is consistent when the sensor needs to
be vflip quirked or not.
Signed-off-by: Grégory Lardière <spmf2004-m560x@yahoo.fr>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SXGA resolution doesn't work unless you first force the VGA resolution.
More investigation is needed in order to fix this the "right" way.
Signed-off-by: Grégory Lardière <spmf2004-m560x@yahoo.fr>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Red and blue balance missed their id fields
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SXGA resolution needs more testing. Disable it for now
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of parameters to some functions in the m5602 are constant and should be flagged as such.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. Support Silicon Cut >= 3.0
2. Remove support for obsolete cuts: 1.0. 1.1. 1.2
3. Try to catch more error cases
Driver doesn't now attach to obsolete silcon cuts, It just simply quits.
Results in code simplification, with removal of the obsolete cuts.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now I relied on i2c_del_adapter to unregister the i2c_clients for
me, however, if the i2c bus is a platform bus then it is never deleted.
So instead I need to unregister i2c clients when unregistering the
v4l2_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a utility function that can be used to setup the v4l2_device's name
field in a standard manner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for tuners with i2c addresses >= 0x65 is dropped since no tuners
with addresses in the range 0x65-0x6f have been found.
This patch removes addresses 0x65-0x6f from the list of tuner probe addresses,
it removes the kernel warning that warned if addresses in this range appeared,
and it removed a hack for the cx88 that is no longer needed now that the
tuner address range is reduced.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx88: Add support for the Hauppauge IROnly board.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/master/v4l/radio-si470x.c: In function 'si470x_fops_release':
/home/v4l/master/v4l/radio-si470x.c:1218: warning: label 'unlock' defined but not used
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
