Kernel time, which advances in discrete steps may progress much slower
than TSC. As a result, when kvmclock is adjusted to a new base, the
apparent time to the guest, which runs at a much higher, nsec scaled
rate based on the current TSC, may have already been observed to have
a larger value (kernel_ns + scaled tsc) than the value to which we are
setting it (kernel_ns + 0).
We must instead compute the clock as potentially observed by the guest
for kernel_ns to make sure it does not go backwards.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The scale_delta function for shift / multiply with 31-bit
precision moves to a common header so it can be used by both
kernel and kvm module.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If there are active VCPUs which are marked as belonging to
a particular hardware CPU, request a clock sync for them when
enabling hardware; the TSC could be desynchronized on a newly
arriving CPU, and we need to recompute guests system time
relative to boot after a suspend event.
This covers both cases.
Note that it is acceptable to take the spinlock, as either
no other tasks will be running and no locks held (BSP after
resume), or other tasks will be guaranteed to drop the lock
relatively quickly (AP on CPU_STARTING).
Noting we now get clock synchronization requests for VCPUs
which are starting up (or restarting), it is tempting to
attempt to remove the arch/x86/kvm/x86.c CPU hot-notifiers
at this time, however it is not correct to do so; they are
required for systems with non-constant TSC as the frequency
may not be known immediately after the processor has started
until the cpufreq driver has had a chance to run and query
the chipset.
Updated: implement better locking semantics for hardware_enable
Removed the hack of dropping and retaking the lock by adding the
semantic that we always hold kvm_lock when hardware_enable is
called. The one place that doesn't need to worry about it is
resume, as resuming a frozen CPU, the spinlock won't be taken.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Make the match of TSC find TSC writes that are close to each other
instead of perfectly identical; this allows the compensator to also
work in migration / suspend scenarios.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add a helper function to compute the kernel time and convert nanoseconds
back to CPU specific cycles. Note that these must not be called in preemptible
context, as that would mean the kernel could enter software suspend state,
which would cause non-atomic operation.
Also, convert the KVM_SET_CLOCK / KVM_GET_CLOCK ioctls to use the kernel
time helper, these should be bootbased as well.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When CPUs with unstable TSCs enter deep C-state, TSC may stop
running. This causes us to require resynchronization. Since
we can't tell when this may potentially happen, we assume the
worst by forcing re-compensation for it at every point the VCPU
task is descheduled.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Move the TSC control logic from the vendor backends into x86.c
by adding adjust_tsc_offset to x86 ops. Now all TSC decisions
can be done in one place.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If creating an SMP guest with unstable host TSC, issue a warning
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This simplifies much of the init code; we can now simply always
call tsc_khz_changed, optionally passing it a new value, or letting
it figure out the existing value (while interrupts are disabled, and
thus, by inference from the rule, not raceful against CPU hotplug or
frequency updates, which will issue IPIs to the local CPU to perform
this very same task).
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Attempt to synchronize TSCs which are reset to the same value. In the
case of a reliable hardware TSC, we can just re-use the same offset, but
on non-reliable hardware, we can get closer by adjusting the offset to
match the elapsed time.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Also, ensure that the storing of the offset and the reading of the TSC
are never preempted by taking a spinlock. While the lock is overkill
now, it is useful later in this patch series.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Change svm / vmx to be the same internally and write TSC offset
instead of bare TSC in helper functions. Isolated as a single
patch to contain code movement.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This is used only by the VMX code, and is not done properly;
if the TSC is indeed backwards, it is out of sync, and will
need proper handling in the logic at each and every CPU change.
For now, drop this test during init as misguided.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
commit ad05c88266b4cce1c820928ce8a0fb7690912ba1
(KVM: create aggregate kvm_total_used_mmu_pages value)
introduce percpu counter kvm_total_used_mmu_pages but never
destroy it, this may cause oops when rmmod & modprobe.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Latest kvm mmu_shrink code rework makes kernel changes kvm->arch.n_used_mmu_pages/
kvm->arch.n_max_mmu_pages at kvm_mmu_free_page/kvm_mmu_alloc_page, which is called
by kvm_mmu_commit_zap_page. So the kvm->arch.n_used_mmu_pages or
kvm_mmu_available_pages(vcpu->kvm) is unchanged after kvm_mmu_prepare_zap_page(),
This caused kvm_mmu_change_mmu_pages/__kvm_mmu_free_some_pages loops forever.
Moving kvm_mmu_commit_zap_page would make the while loop performs as normal.
Reported-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Tested-by: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Of slab shrinkers, the VM code says:
* Note that 'shrink' will be passed nr_to_scan == 0 when the VM is
* querying the cache size, so a fastpath for that case is appropriate.
and it *means* it. Look at how it calls the shrinkers:
nr_before = (*shrinker->shrink)(0, gfp_mask);
shrink_ret = (*shrinker->shrink)(this_scan, gfp_mask);
So, if you do anything stupid in your shrinker, the VM will doubly
punish you.
The mmu_shrink() function takes the global kvm_lock, then acquires
every VM's kvm->mmu_lock in sequence. If we have 100 VMs, then
we're going to take 101 locks. We do it twice, so each call takes
202 locks. If we're under memory pressure, we can have each cpu
trying to do this. It can get really hairy, and we've seen lock
spinning in mmu_shrink() be the dominant entry in profiles.
This is guaranteed to optimize at least half of those lock
aquisitions away. It removes the need to take any of the locks
when simply trying to count objects.
A 'percpu_counter' can be a large object, but we only have one
of these for the entire system. There are not any better
alternatives at the moment, especially ones that handle CPU
hotplug.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Doing this makes the code much more readable. That's
borne out by the fact that this patch removes code. "used"
also happens to be the number that we need to return back to
the slab code when our shrinker gets called. Keeping this
value as opposed to free makes the next patch simpler.
So, 'struct kvm' is kzalloc()'d. 'struct kvm_arch' is a
structure member (and not a pointer) of 'struct kvm'. That
means they start out zeroed. I _think_ they get initialized
properly by kvm_mmu_change_mmu_pages(). But, that only happens
via kvm ioctls.
Another benefit of storing 'used' intead of 'free' is
that the values are consistent from the moment the structure is
allocated: no negative "used" value.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
arch.n_alloc_mmu_pages is a poor choice of name. This value truly
means, "the number of pages which _may_ be allocated". But,
reading the name, "n_alloc_mmu_pages" implies "the number of allocated
mmu pages", which is dead wrong.
It's really the high watermark, so let's give it a name to match:
nr_max_mmu_pages. This change will make the next few patches
much more obvious and easy to read.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
"free" is a poor name for this value. In this context, it means,
"the number of mmu pages which this kvm instance should be able to
allocate." But "free" implies much more that the objects are there
and ready for use. "available" is a much better description, especially
when you see how it is calculated.
In this patch, we abstract its use into a function. We'll soon
replace the function's contents by calculating the value in a
different way.
All of the reads of n_free_mmu_pages are taken care of in this
patch. The modification sites will be handled in a patch
later in the series.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Most x86 two operand instructions allow the destination to be a memory operand,
but IMUL (for example) requires that the destination be a register. Change
____emulate_2op() to take a register for both source and destination so we
can invoke IMUL.
Signed-off-by: Avi Kivity <avi@redhat.com>
emulate_push() only schedules a push; it doesn't actually push anything.
Call writeback() to flush out the write.
Signed-off-by: Avi Kivity <avi@redhat.com>
Change OUT instruction to use dst instead of src, so we can
reuse those code for all out instructions.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce DstImmUByte for dst operand decode, which
will be used for out instruction.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce function write_register_operand() to write back the
register operand.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add kvm_release_page_clean() after is_error_page() to avoid
leakage of error page.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The code for initializing the emulation context is duplicated at two
locations (emulate_instruction() and kvm_task_switch()). Separate it
in a separate function and call it from there.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch lets emulate_grp3() return X86EMUL_* return codes instead
of hardcoded ones.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Mask group 8 instruction as BitOp, so we can share the
code for adjust the source operand.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
adjust the dst address for a register source but not adjust the
address for an immediate source.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If bit offset operands is a negative number, BitOp instruction
will return wrong value. This patch fix it.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch change to disable writeback when decode dest
operand if the dest type is ImplicitOps or not specified.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds support for int instructions to the emulator.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The patch adds a new member get_idt() to x86_emulate_ops.
It also adds a function to get the idt in order to be used by the emulator.
This is needed for real mode interrupt injection and the emulation of int
instructions.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Two-byte opcode always start with 0x0F and the decode flags
of opcode 0xF0 is always 0, so remove dup check.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When using a relocatable kernel we need to make sure that the trampline code
and the interrupt handlers are both copied to low memory. The only way to do
this reliably is to put them in the copied section.
This patch should make relocated kernels work with KVM.
KVM-Stable-Tag
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
On Book3S KVM we directly expose some asm pointers to C code as
variables. These need to be relocated and thus break on relocatable
kernels.
To make sure we can at least build, let's mark them as long instead
of u32 where 64bit relocations don't work.
This fixes the following build error:
WARNING: 2 bad relocations^M
> c000000000008590 R_PPC64_ADDR32 .text+0x4000000000008460^M
> c000000000008594 R_PPC64_ADDR32 .text+0x4000000000008598^M
Please keep in mind that actually using KVM on a relocated kernel
might still break. This only fixes the compile problem.
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Book3S_32 requires MSR_DR to be disabled during load_up_xxx while on Book3S_64
it's supposed to be enabled. I misread the code and disabled it in both cases,
potentially breaking the PS3 which has a really small RMA.
This patch makes KVM work on the PS3 again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
On Book3s_32 the tlbie instruction flushed effective addresses by the mask
0x0ffff000. This is pretty hard to reflect with a hash that hashes ~0xfff, so
to speed up that target we should also keep a special hash around for it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
On failure gfn_to_pfn returns bad_page so use correct function to check
for that.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far we've been running all code without locking of any sort. This wasn't
really an issue because I didn't see any parallel access to the shadow MMU
code coming.
But then I started to implement dirty bitmapping to MOL which has the video
code in its own thread, so suddenly we had the dirty bitmap code run in
parallel to the shadow mmu code. And with that came trouble.
So I went ahead and made the MMU modifying functions as parallelizable as
I could think of. I hope I didn't screw up too much RCU logic :-). If you
know your way around RCU and locking and what needs to be done when, please
take a look at this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Due to previous changes, the Book3S_32 guest MMU code didn't compile properly
when enabling debugging.
This patch repairs the broken code paths, making it possible to define DEBUG_MMU
and friends again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We need to tell the guest the opcodes that make up a hypercall through
interfaces that are controlled by userspace. So we need to add a call
for userspace to allow it to query those opcodes so it can pass them
on.
This is required because the hypercall opcodes can change based on
the hypervisor conditions. If we're running in hardware accelerated
hypervisor mode, a hypercall looks different from when we're running
without hardware acceleration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
On BookE the preferred way to write the EE bit is the wrteei instruction. It
already encodes the EE bit in the instruction.
So in order to get BookE some speedups as well, let's also PV'nize thati
instruction.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is also a form of mtmsr where all bits need to be addressed. While the
PPC64 Linux kernel behaves resonably well here, on PPC32 we do not have an
L=1 form. It does mtmsr even for simple things like only changing EE.
So we need to hook into that one as well and check for a mask of bits that we
deem safe to change from within guest context.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The PowerPC ISA has a special instruction for mtmsr that only changes the EE
and RI bits, namely the L=1 form.
Since that one is reasonably often occuring and simple to implement, let's
go with this first. Writing EE=0 is always just a store. Doing EE=1 also
requires us to check for pending interrupts and if necessary exit back to the
hypervisor.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When we hook an instruction we need to make sure we don't clobber any of
the registers at that point. So we write them out to scratch space in the
magic page. To make sure we don't fall into a race with another piece of
hooked code, we need to disable interrupts.
To make the later patches and code in general easier readable, let's introduce
a set of defines that save and restore r30, r31 and cr. Let's also define some
helpers to read the lower 32 bits of a 64 bit field on 32 bit systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We will need to patch several instruction streams over to a different
code path, so we need a way to patch a single instruction with a branch
somewhere else.
This patch adds a helper to facilitate this patching.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We will soon require more sophisticated methods to replace single instructions
with multiple instructions. We do that by branching to a memory region where we
write replacement code for the instruction to.
This region needs to be within 32 MB of the patched instruction though, because
that's the furthest we can jump with immediate branches.
So we keep 1MB of free space around in bss. After we're done initing we can just
tell the mm system that the unused pages are free, but until then we have enough
space to fit all our code in.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
With our current MMU scheme we don't need to know about the tlbsync instruction.
So we can just nop it out.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some instructions can simply be replaced by load and store instructions to
or from the magic page.
This patch replaces often called instructions that fall into the above category.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We will soon start and replace instructions from the text section with
other, paravirtualized versions. To ease the readability of those patches
I split out the generic looping and magic page mapping code out.
This patch still only contains stubs. But at least it loops through the
text section :).
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We have all the hypervisor pieces in place now, but the guest parts are still
missing.
This patch implements basic awareness of KVM when running Linux as guest. It
doesn't do anything with it yet though.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently x86 is the only architecture that uses kvm_guest_init(). With
PowerPC we're getting a second user, but the signature is different there
and we don't need to export it, as it uses the normal kernel init framework.
So let's move the x86 specific definition of that function over to the x86
specfic header file.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Now that we have the shared page in place and the MMU code knows about
the magic page, we can expose that capability to the guest!
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We need to override EA as well as PA lookups for the magic page. When the guest
tells us to project it, the magic page overrides any guest mappings.
In order to reflect that, we need to hook into all the MMU layers of KVM to
force map the magic page if necessary.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We will be introducing a method to project the shared page in guest context.
As soon as we're talking about this coupling, the shared page is colled magic
page.
This patch introduces simple defines, so the follow-up patches are easier to
read.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
On PowerPC it's very normal to not support all of the physical RAM in real mode.
To check if we're matching on the shared page or not, we need to know the limits
so we can restrain ourselves to that range.
So let's make it a define instead of open-coding it. And while at it, let's also
increase it.
Signed-off-by: Alexander Graf <agraf@suse.de>
v2 -> v3:
- RMO -> PAM (non-magic page)
Signed-off-by: Avi Kivity <avi@redhat.com>
When the guest turns on interrupts again, it needs to know if we have an
interrupt pending for it. Because if so, it should rather get out of guest
context and get the interrupt.
So we introduce a new field in the shared page that we use to tell the guest
that there's a pending interrupt lying around.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
While running in hooked code we need to store register contents out because
we must not clobber any registers.
So let's add some fields to the shared page we can just happily write to.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When running in hooked code we need a way to disable interrupts without
clobbering any interrupts or exiting out to the hypervisor.
To achieve this, we have an additional critical field in the shared page. If
that field is equal to the r1 register of the guest, it tells the hypervisor
that we're in such a critical section and thus may not receive any interrupts.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
To communicate with KVM directly we need to plumb some sort of interface
between the guest and KVM. Usually those interfaces use hypercalls.
This hypercall implementation is described in the last patch of the series
in a special documentation file. Please read that for further information.
This patch implements stubs to handle KVM PPC hypercalls on the host and
guest side alike.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When in kernel mode there are 4 additional registers available that are
simple data storage. Instead of exiting to the hypervisor to read and
write those, we can just share them with the guest using the page.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The SRR0 and SRR1 registers contain cached values of the PC and MSR
respectively. They get written to by the hypervisor when an interrupt
occurs or directly by the kernel. They are also used to tell the rfi(d)
instruction where to jump to.
Because it only gets touched on defined events that, it's very simple to
share with the guest. Hypervisor and guest both have full r/w access.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The DAR register contains the address a data page fault occured at. This
register behaves pretty much like a simple data storage register that gets
written to on data faults. There is no hypervisor interaction required on
read or write.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The DSISR register contains information about a data page fault. It is fully
read/write from inside the guest context and we don't need to worry about
interacting based on writes of this register.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
One of the most obvious registers to share with the guest directly is the
MSR. The MSR contains the "interrupts enabled" flag which the guest has to
toggle in critical sections.
So in order to bring the overhead of interrupt en- and disabling down, let's
put msr into the shared page. Keep in mind that even though you can fully read
its contents, writing to it doesn't always update all state. There are a few
safe fields that don't require hypervisor interaction. See the documentation
for a list of MSR bits that are safe to be set from inside the guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
For transparent variable sharing between the hypervisor and guest, I introduce
a shared page. This shared page will contain all the registers the guest can
read and write safely without exiting guest context.
This patch only implements the stubs required for the basic structure of the
shared page. The actual register moving follows.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
If a nop instruction is encountered, we jump directly to the done label.
This skip updating rip. Break from the switch case instead
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since modrm operand can be either register or memory, decoding it into
a 'struct operand', which can represent both, is simpler.
Signed-off-by: Avi Kivity <avi@redhat.com>
The operands for these instructions are 32 bits or 64 bits, depending on
long mode, and ignoring REX prefixes, or the operand size prefix.
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we use a void pointer for memory addresses. That's wrong since
these are guest virtual addresses which are not directly dereferencable by
the host.
Use the correct type, unsigned long.
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch lets a nested vmrun fail if the L1 hypervisor
left the asid zero. This fixes the asid_zero unit test.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch lets the nested vmrun fail if the L1 hypervisor
has not intercepted vmrun. This fixes the "vmrun intercept
check" unit test.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Mark page dirty only when this page is really written, it's more exacter,
and also can fix dirty page marking in speculation path
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce spte_has_volatile_bits() function to judge whether spte
bits will miss, it's more readable and can help us to cleanup code
later
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
It's a small cleanup that using using kvm_set_pfn_accessed() instead
of mark_page_accessed()
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
No need to update vcpu state since instruction is in the middle of the
emulation.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Needed for repeating instructions with execution functions.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of looking up the opcode twice (once for decode flags, once for
the big execution switch) look up both flags and function in the decode tables.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
It doesn't ever change, so we don't need to pass it around everywhere.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Now that the group index no longer exists, the space is free.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of having a group number, store the group table pointer directly in
the opcode.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We'll be using that to distinguish between new-style and old-style groups.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Once 'struct opcode' grows, its initializer will become more complicated.
Wrap the simple initializers in a D() macro, and replace the empty initializers
with an even simpler N macro.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This will hold all the information known about the opcode. Currently, this
is just the decode flags.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The parenthese make is impossible to use the macros with initializers that
require braces.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Ths patch adds IRET instruction (opcode 0xcf).
Currently, only IRET in real mode is emulated. Protected mode support is to be added later if needed.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Reviewed-by: Avi Kivity <avi@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch implements the emulations of the svm next_rip
feature in the nested svm implementation in kvm.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch fixes a bug in a nested hypervisor that heavily
switches between real-mode and long-mode. The problem is
fixed by syncing back efer into the guest vmcb on emulated
vmexit.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
After commit 53383eaad08d, the '*spte' has updated before call
rmap_remove()(in most case it's 'shadow_trap_nonpresent_pte'), so
remove this information from error message
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Now that we have the host gdt conveniently stored in a variable, make use
of it instead of querying the cpu.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Use just one group table for byte (F6) and word (F7) opcodes.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Move operand decoding to the opcode table, keep lock decoding in the group
table. This allows us to get consolidate the four variants of Group 1 into one
group.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Allow bits that are common to all members of a group to be specified in the
opcode table instead of the group table. This allows some simplification
of the decode tables.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add a decode flag to indicate the instruction is invalid. Will come in useful
later, when we mix decode bits from the opcode and group table.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently group bits are stored in bits 0:7, where operand bits are stored.
Make group bits be 0:3, and move the existing bits 0:3 to 16:19, so we can
mix group and operand bits.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Some instructions are repetitive in the opcode space, add macros for
consolidating them.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If an instruction is present in the decode tables but not in the execution
switch, it will be emulated as a NOP. An example is IRET (0xcf).
Fix by adding default: labels to the execution switches.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* 'softirq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softirqs: Make wakeup_softirqd static
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, asm: Restore parentheses around one pushl_cfi argument
x86, asm: Fix ancient-GAS workaround
x86, asm: Fix CFI macro invocations to deal with shortcomings in gas
* 'x86-numa-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, numa: Assign CPUs to nodes in round-robin manner on fake NUMA
* 'x86-quirks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: HPET force enable for CX700 / VIA Epia LT
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: Use string copy operation to optimze copy in kernel compression
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Use allocated buffer in tlb_uv.c:tunables_read()
* 'x86-vm86-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vm86: Fix preemption bug for int1 debug and int3 breakpoint handlers.
* 'x86-trampoline-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, mm: Add an initial page table for core bootstrapping
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kdb,debug_core: adjust master cpu switch logic against new debug_core locking
debug_core: refactor locking for master/slave cpus
x86,kgdb: remove unnecessary call to kgdb_correct_hw_break()
debug_core: disable hw_breakpoints on all cores in kgdb_cpu_enter()
kdb,kgdb: fix sparse fixups
kdb: Fix oops in kdb_unregister
kdb,ftdump: Remove reference to internal kdb include
kdb: Allow kernel loadable modules to add kdb shell functions
debug_core: stop rcu warnings on kernel resume
debug_core: move all watch dog syncs to a single function
x86,kgdb: fix debugger hw breakpoint test regression in 2.6.35
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
serial8250: ratelimit "too much work" error
serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
serial: abstraction for 8250 legacy ports
serial/imx: check that the buffer is non-empty before sending it out
serial: mfd: add more baud rates support
jsm: Remove the uart port on errors
Alchemy: Add UART PM methods.
8250: allow platforms to override PM hook.
altera_uart: Don't use plain integer as NULL pointer
altera_uart: Fix missing prototype for registering an early console
altera_uart: Fixup type usage of port flags
altera_uart: Make it possible to use Altera UART and 8250 ports together
altera_uart: Add support for different address strides
altera_uart: Add support for getting mapbase and IRQ from resources
altera_uart: Add support for polling mode (IRQ-less)
serial: Factor out uart_poll_timeout() from 8250 driver
serial: mark the 8250 driver as maintained
serial: 8250: Don't delay after transmitter is ready.
tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
vcs: invoke the vt update callback when /dev/vcs* is written to
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: update comments to reflect that percpu allocations are always zero-filled
percpu: Optimize __get_cpu_var()
x86, percpu: Optimize this_cpu_ptr
percpu: clear memory allocated with the km allocator
percpu: fix build breakage on s390 and cleanup build configuration tests
percpu: use percpu allocator on UP too
percpu: reduce PCPU_MIN_UNIT_SIZE to 32k
vmalloc: pcpu_get/free_vm_areas() aren't needed on UP
Fixed up trivial conflicts in include/linux/percpu.h
The kernel debug_core invokes hw breakpoint install and removal via
call backs. The architecture specific kgdb stubs only need to
implement the call backs and not actually call the functions.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: x86@kernel.org
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: H. Peter Anvin <hpa@zytor.com>
Fix the following sparse warnings:
kdb_main.c:328:5: warning: symbol 'kdbgetu64arg' was not declared. Should it be static?
kgdboc.c:246:12: warning: symbol 'kgdboc_early_init' was not declared. Should it be static?
kgdb.c:652:26: warning: incorrect type in argument 1 (different address spaces)
kgdb.c:652:26: expected void const *ptr
kgdb.c:652:26: got struct perf_event *[noderef] <asn:3>*pev
The one in kgdb.c required the (void * __force) because of the return
code from register_wide_hw_breakpoint looking like:
return (void __percpu __force *)ERR_PTR(err);
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
HW breakpoints events stopped working correctly with kgdb as a result
of commit: 018cbffe68 (Merge commit
'v2.6.33' into perf/core), later commit:
ba773f7c51 (x86,kgdb: Fix hw breakpoint
regression) allowed breakpoints to propagate to the debugger core but
did not completely address the original regression in functionality
found in 2.6.35.
When the DR_STEP flag is set in dr6 along with any of the DR_TRAP
bits, the kgdb exception handler will enter once from the
hw_breakpoint API call back and again from the die notifier for
do_debug(), which causes the debugger to stop twice and also for the
kgdb regression tests to fail running under kvm with:
echo V2I1 > /sys/module/kgdbts/parameters/kgdbts
To address the problem, the kgdb overflow handler needs to implement
the same logic as the ptrace overflow handler call back with respect
to updating the virtual copy of dr6. This will allow the kgdb
do_debug() die notifier to properly handle the exception and the
attached debugger, or kgdb test suite, will only receive a single
notification.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: x86@kernel.org
Start unifying the PPI/EPPI peripheral structures in one place. This
may be used by camera/video/fpga/high speed devices.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This matches all the other Blackfin ports and keep us from having to write
bf561-specific code in many places.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the common 8250 serial driver supports an "irqflags" field,
we don't need to patch in a custom define into the code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Different arches use different names, so make sure we define both so
common code (like MTD_XIP) "just works".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mainline version of git merged support for Blackfin parts, but we now
need to propagate the gcc arch define to make it work.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We have to use ioctl numbers that don't collide with common code.
Otherwise, these ones never even get called because the common fs
code swalled all invocations.
Reported-by: Kay Duenzer <kduenzer@maku.eu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This board has a SSM2603 codec, so make sure we have the right resources
declared for it.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The RX/TX address is always the same regardless of the size of the access.
That means there is no dedicated "16bit" or "32bit" MMR. Trying to use
these currently leads to compile errors. So change everything to use the
right MMR define.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: allow people to override individual funcs
bitops: remove duplicated extern declarations
bitops: make asm-generic/bitops/find.h more generic
asm-generic: kdebug.h: Checkpatch cleanup
asm-generic: fcntl: make exported headers use strict posix types
asm-generic: cmpxchg does not handle non-long arguments
asm-generic: make atomic_add_unless a function
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'config' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
BKL: introduce CONFIG_BKL.
dabusb: remove the BKL
sunrpc: remove the big kernel lock
init/main.c: remove BKL notations
blktrace: remove the big kernel lock
rtmutex-tester: make it build without BKL
dvb-core: kill the big kernel lock
dvb/bt8xx: kill the big kernel lock
tlclk: remove big kernel lock
fix rawctl compat ioctls breakage on amd64 and itanic
uml: kill big kernel lock
parisc: remove big kernel lock
cris: autoconvert trivial BKL users
alpha: kill big kernel lock
isapnp: BKL removal
s390/block: kill the big kernel lock
hpet: kill BKL, add compat_ioctl
this patch gives the possibility to workaround bug ENGcm09152
on i.MX35 when the hardware workaround is also implemented on
the board.
It covers the workaround described on page 25 of the following Errata :
http://cache.freescale.com/files/dsp/doc/errata/IMX35CE.pdf
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AM35x has musb interface (version 1.8) and uses CPPI41 DMA engine.
It has USB phy built inside the IP itself.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.
The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Custom UART PM hook for Alchemy chips: do standard UART pm and
additionally en/disable uart block clocks as needed.
This allows to get rid of a debug port PM hack in the Alchemy pm code.
Tested on Db1200.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Again basically cut and paste
Convert the main driver set to use the hooks for GICOUNT
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts s390 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- S390 defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds TIOCGRS485 and TIOCGRS485, which are unused
by any driver available on this architecture
- The generic version adds support for termiox
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts mn10300 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- The generic version provides TIOCGRS485 and TIOCSRS485 but they
are unused by any driver available for this architecture.
- The generic version adds support for termiox
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts m68k to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- m68k defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds TIOCSRS485 and TIOCGRS485m which are unused
by any driver available on this architecture.
- The generic version adds support for termiox
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts m32r to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- The generic version adds TIOCGRS485 and TIOCGRS485, which are unused by
any driver available on this architecture.
- The generic version adds support for termiox
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts ia64 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- The generic version adds TIOCSRS485 and TIOCGRS485, which are unused
by any driver available on this architecture.
- The generic version adds support for termiox
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts h8300 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- H8300 defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds TIOCSRS485 and TIOGSRS485, but are unused
by any driver available on this architecture.
- The generic version adds support for termiox
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
