Commit Graph

62 Commits

Author SHA1 Message Date
Matt Domsch
6b4b78fed4 PCI: optionally sort device lists breadth-first
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation.  Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively.  Many people have come to expect this naming.  Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations).  I also have reports that various Sun and HP servers
have similar behavior.


Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also).  2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.

On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1.  If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.

A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.

-[0000:00]-+-00.0  Intel Corporation 5000P Chipset Memory Controller Hub
           +-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0  Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
           +-1c.0-[0000:01-02]----00.0-[0000:02]----00.0  Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)


Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.


Solution:

The solution can come in multiple steps.

Suggested fix #1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels.  It adds two new
command line options:
  pci=bfsort
  pci=nobfsort
to force the sort order, or not, as you wish.  It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".


Suggested fix #2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in.  I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first.  It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.

Suggested fix #3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order.  This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers).  I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.


Feedback appreciated.  Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.

You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm.  I think
that's both safe and appropriate in this instance.


Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-10-18 11:36:12 -07:00
Alan Cox
29f3eb6463 pci: Additional search functions
In order to finish converting to pci_get_* interfaces we need to add a couple
of bits of missing functionaility

pci_get_bus_and_slot() provides the equivalent to pci_find_slot()
(pci_get_slot is already taken as a name for something similar but not the
same)

pci_get_device_reverse() is the equivalent of pci_find_device_reverse but
refcounting

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-10-18 11:36:12 -07:00
Eric W. Biederman
95d77884c7 [PATCH] htirq: tidy up the htirq code
This moves the declarations for the architecture helpers into
include/linux/htirq.h from the generic include/linux/pci.h.  Hopefully this
will make this distinction clearer.

htirq.h is included where it is needed.

The dependency on the msi code is fixed and removed.

The Makefile is tidied up.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 07:55:30 -07:00
Eric W. Biederman
3b7d1921f4 [PATCH] msi: refactor and move the msi irq_chip into the arch code
It turns out msi_ops was simply not enough to abstract the architecture
specific details of msi.  So I have moved the resposibility of constructing
the struct irq_chip to the architectures, and have two architecture specific
functions arch_setup_msi_irq, and arch_teardown_msi_irq.

For simple architectures those functions can do all of the work.  For
architectures with platform dependencies they can call into the appropriate
platform code.

With this msi.c is finally free of assuming you have an apic, and this
actually takes less code.

The helpers for the architecture specific code are declared in the linux/msi.h
to keep them separate from the msi functions used by drivers in linux/pci.h

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 07:55:29 -07:00
Eric W. Biederman
8b955b0ddd [PATCH] Initial generic hypertransport interrupt support
This patch implements two functions ht_create_irq and ht_destroy_irq for
use by drivers.  Several other functions are implemented as helpers for
arch specific irq_chip handlers.

The driver for the card I tested this on isn't yet ready to be merged.
However this code is and hypertransport irqs are in use in a few other
places in the kernel.  Not that any of this will get merged before 2.6.19

Because the ipath-ht400 is slightly out of spec this code will need to be
generalized to work there.

I think all of the powerpc uses are for a plain interrupt controller in a
chipset so support for native hypertransport devices is a little less
interesting.

However I think this is a half way decent model on how to separate arch
specific and generic helper code, and I think this is a functional model of
how to get the architecture dependencies out of the msi code.

[akpm@osdl.org: Kconfig fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 07:55:29 -07:00
Eric W. Biederman
38bc036130 [PATCH] genirq: msi: refactor the msi_ops
The current msi_ops are short sighted in a number of ways, this patch attempts
to fix the glaring deficiences.

- Report in msi_ops if a 64bit address is needed in the msi message, so we
  can fail 32bit only msi structures.

- Send and receive a full struct msi_msg in both setup and target.  This is
  a little cleaner and allows for architectures that need to modify the data
  to retarget the msi interrupt to a different cpu.

- In target pass in the full cpu mask instead of just the first cpu in case
  we can make use of the full cpu mask.

- Operate in terms of irqs and not vectors, currently there is still a 1-1
  relationship but on architectures other than ia64 I expect this will change.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 07:55:27 -07:00
Eric W. Biederman
0366f8f713 [PATCH] genirq: msi: implement helper functions read_msi_msg and write_msi_msg
In support of this I also add a struct msi_msg that captures the the two
address and one data field ina typical msi message, and I remember the pos and
if the address is 64bit in struct msi_desc.

This makes the code a little more readable and easier to maintain, and paves
the way to further simplfications.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 07:55:27 -07:00
Alan Cox
236561e5df [PATCH] PCI quirks update
This fixes two things

Firstly someone mistakenly used "errata" for the singular.  This causes
Dave Woodhouse to emit diagnostics whenever the string is read, and so
should be fixed.

Secondly the AMD AGP tunnel has an erratum which causes hangs if you try
and do direct PCI to AGP transfers in some cases.  We have a flag for
PCI/PCI failures but we need a different flag for this really as in this
case we don't want to stop PCI/PCI transfers using things like IOAT and the
new RAID offload work.

I'll post some updates to make proper use of the PCIAGP flag in the
media/video drivers to Mauro.

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01 00:39:17 -07:00
Satoru Takeuchi
24f8aa9b46 PCI: add pci_stop_bus_device
This patch adds pci_stop_bus_device() which stops a PCI device (detach
the driver, remove from the global list and so on) and any children.
This is needed for ACPI based PCI-to-PCI bridge hot-remove, and it will
be also needed for ACPI based PCI root bridge hot-remove.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-26 17:43:54 -07:00
Alan Cox
50b0075520 PCI: Multiprobe sanitizer
There are numerous drivers that can use multithreaded probing but having
some kind of global flag as the way to control this makes migration to
threaded probing hard and since it enables it everywhere and is almost
as likely to cause serious pain as holding a clog dance in a minefield.

If we have a pci_driver multithread_probe flag to inherit you can turn
it on for one driver at a time.

From playing so far however I think we need a different model at the
device layer which serializes until the called probe function says "ok
you can start another one now". That would need some kind of flag and
semaphore plus a helper function.

Anyway in the absence of that this is a starting point to usefully play
with this stuff

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-26 17:43:53 -07:00
Greg Kroah-Hartman
b19441af18 PCI: fix __must_check warnings
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-26 17:43:53 -07:00
Andrew Morton
4a7fb6363f add __must_check to device management code
We're getting a lot of crashes in the sysfs/kobject/device/bus/class code and
they're very hard to diagnose.

I'm suspecting that in some cases this is because drivers aren't checking
return values and aren't handling errors correctly.  So the code blithely
blunders on and crashes later in very obscure ways.

There's just no reason to ignore errors which can and do occur.  So the patch
sprinkles __must_check all over these APIs.

Causes 1,513 new warnings.  Heh.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-25 21:08:39 -07:00
David Brownell
1d3a82af45 PM: no suspend_prepare() phase
Remove the new suspend_prepare() phase.  It doesn't seem very usable,
has never been tested, doesn't address fault cleanup, and would need
a sibling resume_complete(); plus there are no real use cases.  It
could be restored later if those issues get resolved.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-25 21:08:38 -07:00
Linus Torvalds
cbd69dbbf1 Suspend changes for PCI core
Changes the PCI core to use the new suspend infrastructure changes.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-25 21:08:37 -07:00
Kristen Carlson Accardi
ffadcc2ff4 [PATCH] PCI: PCIE power management quirk
When changing power states from D0->DX and then from DX->D0, some
Intel PCIE chipsets will cause a device reset to occur.  This will
cause problems for any D State other than D3, since any state
information that the driver will expect to be present coming from
a D1 or D2 state will have been cleared.  This patch addes a
flag to the pci_dev structure to indicate that devices should
not use states D1 or D2, and will set that flag for the affected
chipsets.  This patch also modifies pci_set_power_state() so that
when a device driver tries to set the power state on
a device that is downstream from an affected chipset, or on one
of the affected devices it only allows state changes to or
from D0 & D3.  In addition, this patch allows the delay time
between D3->D0 to be changed via a quirk.  These chipsets also
need additional time to change states beyond the normal 10ms.

Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-07-12 16:05:48 -07:00
Greg Kroah-Hartman
e31dd6e452 [PATCH] 64bit resource: change pci core and arch code to use resource_size_t
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>

Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-27 09:24:00 -07:00
Shaohua Li
99dc804d9b [PATCH] PCI: disable msi mode in pci_disable_device
Brice said the pci_save_msi_state breaks his driver in his special usage
(not in suspend/resume), as pci_save_msi_state will disable msi mode. In
his usage, pci_save_state will be called at runtime, and later (after
the device operates for some time and has an error) pci_restore_state
will be called.
In another hand, suspend/resume needs disable msi mode, as device should
stop working completely. This patch try to workaround this issue.
Drivers are expected call pci_disable_device in suspend time after
pci_save_state.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21 12:00:00 -07:00
Doug Thompson
bd8481e164 [PATCH] PCI Bus Parity Status-broken hardware attribute, EDAC foundation
Currently, the EDAC (error detection and correction) modules that are in
the kernel contain some features that need to be moved. After some good
feedback on the PCI Parity detection code and interface
(http://www.ussg.iu.edu/hypermail/linux/kernel/0603.1/0897.html) this
patch ADDs an new attribute to the pci_dev structure: Namely the
'broken_parity_status' bit.

When set this indicates that the respective hardware generates false
positives of Parity errors.

The EDAC "blacklist" solution was inferior and will be removed in a
future patch.

Also in this patch is a PCI quirk.c entry for an Infiniband PCI-X card
which generates false positive parity errors.

I am requesting comments on this AND on the possibility of a exposing
this 'broken_parity_status' bit to userland via the PCI device sysfs
directory for devices. This access would allow for enabling of this
feature on new devices and for old devices that have their drivers
updated. (SLES 9 SP3 did this on an ATI motherboard video device). There
is a need to update such a PCI attribute between kernel releases.

This patch just adds a storage place for the attribute and a quirk entry
for a known bad PCI device. PCI Parity reaper/harvestor operations are
in EDAC itself and will be refactored to use this PCI attribute instead
of its own mechanisms (which are currently disabled) in the future.

Signed-off-by: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21 11:59:59 -07:00
Kumar Gala
75acfecaa0 [PATCH] PCI: Add pci_assign_resource_fixed -- allow fixed address assignments
PCI: Add pci_assign_resource_fixed -- allow fixed address assignments

On some embedded systems the PCI address for hotplug devices are not only
known a priori but are required to be at a given PCI address for other
master in the system to be able to access.

An example of such a system would be an FPGA which is setup from user space
after the system has booted.  The FPGA may be access by DSPs in the system
and those DSPs expect the FPGA at a fixed PCI address.

Added pci_assign_resource_fixed() as a way to allow assignment of the PCI
devices's BARs at fixed PCI addresses.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21 11:59:59 -07:00
Linus Torvalds
cee4cca740 Merge git://git.infradead.org/hdrcleanup-2.6
* git://git.infradead.org/hdrcleanup-2.6: (63 commits)
  [S390] __FD_foo definitions.
  Switch to __s32 types in joystick.h instead of C99 types for consistency.
  Add <sys/types.h> to headers included for userspace in <linux/input.h>
  Move inclusion of <linux/compat.h> out of user scope in asm-x86_64/mtrr.h
  Remove struct fddi_statistics from user view in <linux/if_fddi.h>
  Move user-visible parts of drivers/s390/crypto/z90crypt.h to include/asm-s390
  Revert include/media changes: Mauro says those ioctls are only used in-kernel(!)
  Include <linux/types.h> and use __uXX types in <linux/cramfs_fs.h>
  Use __uXX types in <linux/i2o_dev.h>, include <linux/ioctl.h> too
  Remove private struct dx_hash_info from public view in <linux/ext3_fs.h>
  Include <linux/types.h> and use __uXX types in <linux/affs_hardblocks.h>
  Use __uXX types in <linux/divert.h> for struct divert_blk et al.
  Use __u32 for elf_addr_t in <asm-powerpc/elf.h>, not u32. It's user-visible.
  Remove PPP_FCS from user view in <linux/ppp_defs.h>, remove __P mess entirely
  Use __uXX types in user-visible structures in <linux/nbd.h>
  Don't use 'u32' in user-visible struct ip_conntrack_old_tuple.
  Use __uXX types for S390 DASD volume label definitions which are user-visible
  S390 BIODASDREADCMB ioctl should use __u64 not u64 type.
  Remove unneeded inclusion of <linux/time.h> from <linux/ufs_fs.h>
  Fix private integer types used in V4L2 ioctls.
  ...

Manually resolve conflict in include/linux/mtd/physmap.h
2006-06-20 15:10:08 -07:00
Brice Goglin
3a720d726a [PATCH] Revive pci_find_ext_capability
This patch revives pci_find_ext_capability (has been disabled a couple month
ago since it was not used anywhere. See http://lkml.org/lkml/2006/1/20/247).
It will now be used by the myri10ge driver.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>

 drivers/pci/pci.c   |    3 +--
 include/linux/pci.h |    2 ++
 2 files changed, 3 insertions(+), 2 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-24 00:27:31 -04:00
David Woodhouse
778382e08c Don't include <linux/mod_devicetable.h> in public part of linux/pci.h
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2006-04-29 01:46:02 +01:00
David Woodhouse
62c4f0a2d5 Don't include linux/config.h from anywhere else in include/
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2006-04-26 12:56:16 +01:00
Roland Dreier
e778272dd5 [PATCH] PCI: fix sparse warning about pci_bus_flags
Sparse warns about casting to a __bitwise type.  However, it's correct
to do when defining the enum for pci_bus_flags_t, so add a __force to
quiet the warnings.  This will fix getting

    include/linux/pci.h💯26: warning: cast to restricted type

from sparse all over the build.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-04-14 12:25:25 -07:00
Shaohua Li
41017f0cac [PATCH] PCI: MSI(X) save/restore for suspend/resume
Add MSI(X) configure sapce save/restore in generic PCI helper.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-04-14 12:25:25 -07:00
Jeff Garzik
3c990e9219 [PATCH] PCI: fix pci_request_region[s] arg
Add missing 'const' to pci_request_region[s] 'res_name' arg,
    since we pass it directly to __request_region(), whose 'name' arg
    is also const.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-23 14:35:16 -08:00
Michael S. Tsirkin
6e325a62a0 [PATCH] PCI: make MSI quirk inheritable from the pci bus
It turns out AMD 8131 quirk only affects MSI for devices behind the 8131 bridge.
Handle this by adding a flags field in pci_bus, inherited from parent to child.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-23 14:35:14 -08:00
Kristen Accardi
b82db5cedf [PATCH] PCI: return max reserved busnr
Change the semantics of this call to return the max reserved
bus number instead of just the max assigned bus number.

Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-23 14:35:10 -08:00
Adrian Bunk
f8d6571333 [PATCH] PCI: drivers/pci/pci.c: #if 0 pci_find_ext_capability()
This patch #if 0's the unused global function pci_find_ext_capability().

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-31 18:00:11 -08:00
linas
392a1ce761 [PATCH] PCI Error Recovery: header file patch
Various PCI bus errors can be signaled by newer PCI controllers.
Recovering from those errors requires an infrastructure to notify
affected device drivers of the error, and a way of walking through a
reset sequence.  This patch adds a set of callbacks to be used by error
recovery routines to notify device drivers of the various stages of
recovery.

Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-09 12:13:21 -08:00
Benjamin Herrenschmidt
ac7dc65ac0 [PATCH] PCI: Export pci_cfg_space_size
The powerpc PCI code sets up the PCI tree without doing config space
accesses in most cases, from the firmware tree. However, it still wants
to call pci_cfg_space_size() under some conditions, thus it needs to
be made non-static (though I don't see a point to export it to modules).

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-09 12:13:19 -08:00
Kristen Accardi
ffeff788d6 [PATCH] pci: store PCI_INTERRUPT_PIN in pci_dev
Store the value of the INTERRUPT_PIN in the pci_dev structure
so that it can be retrieved later.

Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-09 12:13:13 -08:00
Greg Kroah-Hartman
249bb070f5 [PATCH] PCI: removed unneeded .owner field from struct pci_driver
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-11-10 16:09:17 -08:00
Laurent riffard
863b18f4b5 [PATCH] PCI: automatically set device_driver.owner
A nice feature of sysfs is that it can create the symlink from the
driver to the module that is contained in it.

It requires that the device_driver.owner is set, what is not the
case for many PCI drivers.

This patch allows pci_register_driver to set automatically the
device_driver.owner for any PCI driver.

Credits to Al Viro who suggested the method.

Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
--

 drivers/ide/setup-pci.c  |   12 +++++++-----
 drivers/pci/pci-driver.c |    9 +++++----
 include/linux/ide.h      |    3 ++-
 include/linux/pci.h      |   10 ++++++++--
 4 files changed, 22 insertions(+), 12 deletions(-)
2005-11-10 16:09:16 -08:00
Roland Dreier
24a4e37706 [PATCH] PCI: add pci_find_next_capability()
Some devices have more than one capability of the same type.  For
example, the PCI header for the PathScale InfiniPath looks like:

	04:01.0 InfiniBand: Unknown device 1fc1:000d (rev 02)
		Subsystem: Unknown device 1fc1:000d
		Flags: bus master, fast devsel, latency 0, IRQ 193
		Memory at fea00000 (64-bit, non-prefetchable) [size=2M]
		Capabilities: [c0] HyperTransport: Slave or Primary Interface
		Capabilities: [f8] HyperTransport: Interrupt Discovery and Configuration

There are _two_ HyperTransport capabilities, and the PathScale driver
wants to look at both of them.

The current pci_find_capability() API doesn't work for this, since it
only allows us to get to the first capability of a given type.  The
patch below introduces a new pci_find_next_capability(), which can be
used in a loop like

	for (pos = pci_find_capability(pdev, <ID>);
	     pos;
	     pos = pci_find_next_capability(pdev, pos, <ID>)) {
		/* ... */
	}

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-11-10 16:09:14 -08:00
Brian King
e04b0ea2e0 [PATCH] PCI: Block config access during BIST
Some PCI adapters (eg.  ipr scsi adapters) have an exposure today in that they
issue BIST to the adapter to reset the card.  If, during the time it takes to
complete BIST, userspace attempts to access PCI config space, the host bus
bridge will master abort the access since the ipr adapter does not respond on
the PCI bus for a brief period of time when running BIST.  On PPC64 hardware,
this master abort results in the host PCI bridge isolating that PCI device
from the rest of the system, making the device unusable until Linux is
rebooted.  This patch is an attempt to close that exposure by introducing some
blocking code in the PCI code.  When blocked, writes will be humored and reads
will return the cached value.  Ben Herrenschmidt has also mentioned that he
plans to use this in PPC power management.

Signed-off-by: Brian King <brking@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/pci/access.c    |   89 ++++++++++++++++++++++++++++++++++++++++++++++++
 drivers/pci/pci-sysfs.c |   20 +++++-----
 drivers/pci/pci.h       |    7 +++
 drivers/pci/proc.c      |   28 +++++++--------
 drivers/pci/syscall.c   |   14 +++----
 include/linux/pci.h     |    7 +++
 6 files changed, 134 insertions(+), 31 deletions(-)
2005-10-28 15:36:58 -07:00
Linus Torvalds
9c8550ee25 Remove "must_check" attributes in PCI-land
Don't just irritate all other kernel developers.  Fix the users first,
then you can re-introduce the must-check infrastructure to avoid new
cases creeping in.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 15:43:46 -07:00
Linus Torvalds
41d0ab2a7d Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6 2005-09-09 15:17:00 -07:00
Paul Mackerras
cdb9b9f730 [PATCH] PCI: Small rearrangement of PCI probing code
This patch makes some small rearrangements of the PCI probing code in
order to make it possible for arch code to set up the PCI tree
without needing to duplicate code from the PCI layer unnecessarily.
PPC64 will use this to set up the PCI tree from the Open Firmware
device tree, which we need to do on logically-partitioned pSeries
systems.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-09 13:58:45 -07:00
Dominik Brodowski
b3743fa444 [PATCH] yenta: share code with PCI core
Share code between setup-bus.c and yenta_socket.c: use the write-out code of
resources to the bridge also in yenta_socket.c, as it provides useful debug
output.  In addition, it fixes the bug that the CPU-centric resource view
might need to be transferred to the PCI-centric view: setup-bus.c does that,
while yenta-socket.c did not.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 13:57:47 -07:00
Dave Jones
144a50ea5e [PATCH] must_check attributes for PCI layer.
Self explanatory really. Some newer gcc's print a warning
if a function is used and we don't check its result.
We do this for a bunch of things in the kernel already,
this extends that to the PCI layer.

Based on a patch originally from Arjan van de Ven.

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-09 11:24:31 -07:00
Brett M Russ
a04ce0ffca [PATCH] PCI/libata INTx cleanup
Simple cleanup to eliminate X copies of the pci_enable_intx() function
in libata.  Moved ahci.c's pci_intx() to pci.c and use it throughout
libata and msi.c.

Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-08 15:07:08 -07:00
Daniel Ritz
3fe9d19f9e [PATCH] PCI: Support PCM PM CAP version 3
- support PCI PM CAP version 3 (as defined in PCI PM Interface Spec v1.2)

- pci/probe.c sets the PM state initially to 4 which is D3cold.  add a
  PCI_UNKNOWN

- minor cleanups

Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-08 15:04:30 -07:00
Paul Mackerras
cecf4864cf [PATCH] PCI: Add pci_walk_bus function to PCI core (nonrecursive)
The PCI error recovery infrastructure needs to be able to contact all
the drivers affected by a PCI error event, which may mean traversing
all the devices under a given PCI-PCI bridge.  This patch adds a
function to the PCI core that traverses all the PCI devices on a PCI
bus and under any PCI-PCI bridges on that bus (and so on), calling a
given function for each device.  This provides a way for the error
recovery code to iterate through all devices that are affected by an
error event.

This version is not implemented as a recursive function.  Instead,
when we reach a PCI-PCI bridge, we set the pointers to start doing the
devices on the bus under the bridge, and when we reach the end of a
bus's devices, we use the bus->self pointer to go back up to the next
higher bus and continue doing its devices.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-08 15:04:30 -07:00
John W. Linville
064b53dbcc [PATCH] PCI: restore BAR values after D3hot->D0 for devices that need it
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0.  This leaves such
a device in an inaccessible state.  The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.

The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.

Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot.  Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.

Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification.  This is
especially true since often many devices are covered by the same
driver.  It likely would be necessary to replicate code across dozens
of drivers.

The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register.  I believe it is safe to include
this patch as part of the PCI infrastructure.

The cleanest implementation of pci_restore_bars was to call
pci_update_resource.  Unfortunately, that does not currently exist
for the sparc64 architecture.  The patch below includes a null
implemenation of pci_update_resource for sparc64.

Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-08 14:57:24 -07:00
Greg Kroah-Hartman
4352dfd5cd [PATCH] PCI: clean up pci.h and split pci register info to separate header file.
This cleans up some of the #ifdef CONFIG_PCI stuff up, and moves the pci register
info out to a separate file, where it belongs.  Eventually we can stop including
this file from within pci.h, but lots of code needs to be audited first.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-08 14:57:24 -07:00
Adrian Bunk
982245f017 [PATCH] PCI: remove CONFIG_PCI_NAMES
This patch removes CONFIG_PCI_NAMES.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-08 14:57:23 -07:00
akpm@osdl.org
74d863ee8a [PATCH] PCI: Move PCI fixup data into r/o section
Make PCI fixup data const, so it'll end up in a r/o section.

This also fixes the conversion into ECOFF which gets broken by too many
changes between r/w and r/o sections.  Call it a hack but it's a change
that's correct by itself.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-08 14:57:23 -07:00
Kristen Accardi
4602b88d97 [PATCH] PCI: 6700/6702PXH quirk
On the 6700/6702 PXH part, a MSI may get corrupted if an ACPI hotplug
driver and SHPC driver in MSI mode are used together.

This patch will prevent MSI from being enabled for the SHPC as part of
an early pci quirk, as well as on any pci device which sets the no_msi
bit.

Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-16 21:06:24 -07:00
Linus Torvalds
dc836b5b6f Revert "[PATCH] PCI: restore BAR values..."
Revert commit fec59a711e, which is
breaking sparc64 that doesn't have a working pci_update_resource.

We'll re-do this after 2.6.13 when we'll do it all properly.
2005-08-08 18:46:09 -07:00