Check for error return from pci_map_single/pci_map_page and clean up.
With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the suspend and resume implementation in the HECC (CAN)
driver.
Signed-off-by: K R Baalaaji <krbaalaaji@ti.com>
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Anant Gole <anantgole@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Dillow took my suggestions and improved on them.
Here is this latest version.
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Remove #define ERR_PFX
Remove now unused member name from struct typhoon
Use pr_<level>
Use netdev_<level>
Coalesce long formats
Remove version information
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion in bf0dcbd929 missed the
new allocation in b44_rx.
This patch was used in OpenWRT for a long time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do a PHY reset to test if there is an active phy and set the PHY address
to B44_PHY_ADDR_NO_PHY in case of an not active phy. This is needed for
the Linksys WRTSL54GS and Asus WL-500W.
This patch was used in OpenWRT for a long time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PowerPC architecture does not require loads to independent bytes to be
ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header and data
are in different descriptors. If the reads go out of order we may have data
that doesn't match the TCP/IP header. Since we use hardware checksumming this
bad data is never verified and it makes it all the way to the application.
This bug was found during stress testing and adding this barrier has been shown
to fix it.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts mwl8k to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
The new callbacks can sleep, so a lot of
code can be removed now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the frame control for ieee80211_is_data_qos() is true before
counting the number of tfds can be free, the tfds_in_queue only
increment when ieee80211_is_data_qos() is true before transmit; so it
should only decrement if the type match.
Remove ieee80211_is_data_qos check for frame_ctrl in tx_resp to avoid
invalid information pass from uCode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receive reply_tx and ready to decrement the count for number of
tfds in queue, do error checking to prevent error condition and
tfds_in_queue become negative number.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix commit 4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when
appropriate)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certain skews of the BE adapter, H/W Tx and Rx
counters could be common for more than one interface.
Add Tx and Rx counters in the adapter structure
(to maintain stats on a per interfae basis).
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently use of 64-bit DMA is disabled in r8169 unless the user passes the
use_dac module option. This is reasonable for conventional PCI devices where
broken chipsets may not handle dual-address-cycle transfers properly for
32-bit slots and so this may not be safe. However, PCI Express should not have
this problem and not using 64-bit DMA results in DMA transfers needlessly using
the IOMMU or SWIOTLB. Set the use_dac module parameter to a new default value of
-1 which results in 64-bit DMA being enabled by default for PCI Express devices
only.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The temperature and voltage limits currently set on these boards are
too conservative and will cause the driver to stop the net device
erroneously in some systems.
Based on a review of the chip datasheets and advice from the designer
of these boards:
- Raise the maximum board temperatures to the specified maximum ambient
temperatures for their PHYs plus the expected temperature bias of the
board
- Raise the maximum controller temperature to 90 degrees
- Lower the minimum temperatures to 0 degrees
- Widen the voltage tolerances to at least +/- 10%
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_mcdi_poll() uses positive error numbers, matching the MCDI
protocol. It must negate the result of efx_mcdi_poll_reboot() which
returns the usual negative error numbers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are only two users of the dma_sync_single_range_for_cpu/device
API in mainline (mlx4 and ssb). The
dma_sync_single_range_for_cpu/device API has never been documented and
the dma_sync_single_for_cpu/device API also support a partial sync.
This converts mlx4 to use the dma_sync_single_for_cpu/device API
(preparations for the removal of the dma_sync_single_range_for_cpu/device API).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
removed fill_multicast_tbl function in smc91c92_cs and do the work inline
rewritten set_addresses function in xirc2ps_cs. This was kinda headache.
Simulated the original and new functions and they bahave the same.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts ath9k to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts mac80211_hwsim to use the new
station add/remove callbacks instead of using
the old sta_notify callback.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts p54 to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ar9170 to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In AP mode, ath_beacon_config_ap only restarts the timer if a TSF
restart is requested. Apparently this was added, because this function
unconditionally sets the flag for TSF reset.
The problem with this is, that ath9k_hw_reset() clobbers the timer
registers (specified in the initvals), thus effectively disabling the
SWBA interrupt whenever a card reset without TSF reset is issued
(happens in a few places in the code).
This patch fixes ath_beacon_config_ap to only issue the TSF reset flag
when necessary, but reinitialize the timer unconditionally. Tests show,
that this is enough to keep the SWBA interrupt going after a call to
ath_reset()
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding debugfs file to monitor the counters and other
information related to "force_reset" request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use different timing duration check for different type of force reset,
force reset request can come from different source and based on
different reason; one type of reset request should not block other type of
reset request.
Adding structure to keep track of different force reset request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Indicate calibration version to uCode
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Until now it was only possible to have one synchronous command running at
any time. If a synchronous command is in progress when a second request
arrives then the second command will fail. Create a new mutex specific for
this purpose to only allow one synchronous command at a time, but enable
other commands to wait instead of fail if a synchronous command is in
progress.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 includes iwl-core.h in which these STATUS flags are already
defined. This also removes a potential confusing definition with iwlcore
using STATUS_MODE_PENDING with value 18 and iwl3945 defining (but not
using) STATUS_CONF_PENDING for value 18.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When selecting the tx fallback rate, rc.c used a separate variable
'nrix' for storing the next rate index, however it did not use that as
reference for further rate index lowering. Because of that, it ended up
reusing the same rate for multiple multi-rate retry stages, thus
decreasing delivery probability under changing link conditions.
This patch removes the separate (unnecessary) variable and fixes
fallback the way it was intended to work.
This should result in increased throughput and better link stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved allocation and freeing of context structure of the driver to
separate functions from probe and remove functions.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added reset and init functions to IO layer of the driver.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for integration of SDIO implementation renamed some IO
functions from wl1271_spi_* form to wl1271_*.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In prepraration for integration of SDIO implementation moved some IO
functions common for SPI and SDIO to separate file.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testmode will be used to send PLT (Production Line Testing) commands
from user space.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon filter table configuration ACX structure had certain elements
reversed, resulting in firmware instability in regard of the feature. Fix
the structure.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If re-configuring the SSID while ad-hoc was already enabled, the beacon
template would be properly updated, but the SSID passed in the CMD_JOIN would
not - hence filtering etc would not work properly.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WEP key index handling was broken: the default key when using key 0 was never
specified to the FW, and if using other default than 0, it would be set on the
TX path for every single TX'd frame.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new firmware does not allow removal of unicast keys - they will be
automatically removed on the next CMD_JOIN.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of acking RX packets read from the FW once all (of several possible)
buffered packets are retrieved, ack packets one by one as they are read. This
enables the FW to start receiving more packets from the network while the
host read operation is still ongoing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
elp_wakeup() was missing in op_conf_tx() which caused wakeup problems in
power save. I forgot to add this part when porting the patch from wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If reverting to a random MAC address, the driver would not update it to the
NVS file, and hence the firmware frame filtering would not work properly.
So update the randomized MAC address to the NVS image.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our NVS uploading mechanism had a bug that was causing it to pass three extra
zeros at the start of the NVS. This may be a problem in the NVS generation
application, but for now we fix it in the driver.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to configure PLT mode almost in the same way as normal mode. Most of
the configuration functions need to be called also when entering PLT, with
the exception of a few RX and TX configuration (which cause mac80211 warnings
if enable while runnning PLT tests).
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always randomizing the MAC address, retrieve and configure the
MAC address from the device specific nvs file. For now, randomize an address
only if the address in the NVS is zero.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the hardcoded general and radio parameter configuration in the driver
with configuration taken from the NVS file directly. Also remove the driver
dependency to the structures with the parameter data.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that necessary commands for WMM are implemented, implement queue handling
for WMM. But WMM is not enabled yet, only one queue is used.
Based on a similar patch from wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For WMM we need to configure each tid separately so modify
wl1271_acx_tid_cfg() to take the configuration from function parameters
instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For WMM we need to configure each queue separately so modify
wl1271_acx_ac_cfg() to take the configuration from function parameters
instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds code to extract the SSID from the beacon template used for
ad-hoc. The mac80211 currently does not provide the SSID, so this is a
workaround for that, for now.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel changing code would a) change the BSSID to a dummy on upon
channel change, breaking connectivity, and b) not update the channel number
at all for ad-hoc, breaking adhoc.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the PSM entry function assumes successful operation, and enables
ELP, BET and beacon filtering right away. This is bad, because the PSM
entry may fail due to environmental issues, which will cause the ELP, BET and
beacon filtering to be illegally enabled (because FW remains in active state.)
Fix this by enabling ELP, BET and beacon filtering only after successful entry,
and by ensuring the firmware is in active mode after the failure.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yet another USB ID.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix off by one error in the queue size check of p54_tx_qos_accounting_alloc()
Coverity CID: 13314
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
...and use it in hostap_cs and orinoco_cs.
Another PCMCIA device with Intersil Prism chipset has been reported:
Socket 0:
product info: "Gigabyte", "GN-WLM01_P25L_ADAPTER", "ISL37300P", "Eval-RevA"
manfid: 0x02e0, 0x1011
function: 6 (network)
As it's the case with some other Prism based devices, the third ID
string contains a design name that should be sufficient to identify the
card as having Intersil Prism chipset and thus compatible with both
orinoco_cs and hostap_cs.
Introduce PCMCIA_DEVICE_PROD_ID3 that matches the third ID string only.
Use it in orinoco_cs and hostap_cs to match cards with the third ID
string indicating Prism chipset. Remove corresponding entries that use
PCMCIA_DEVICE_PROD_ID123.
Reported-by: Ozzy <ozzymud@gmail.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HT extension channel settings require priv->staging_rxon.channel to be
accurate. However, iwl_set_rxon_ht was being called before iwl_set_rxon_channel
and thus HT40 could be broken unless another call to iwl_mac_config came in.
This problem was recently introduced by "iwlwifi: Fix to set correct ht
configuration"
The particular setting in which I noticed this was monitor mode:
iwconfig wlan0 mode monitor
ifconfig wlan0 up
./iw wlan0 set channel 64 HT40-
#./iw wlan0 set channel 64 HT40-
tcpdump -i wlan0 -y IEEE802_11_RADIO
would only catch HT40 packets if I issued the IW command twice.
From visual inspection, iwl_set_rxon_channel does not depend on
iwl_set_rxon_ht, so simply swapping them should be safe and fixes this problem.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level> and netif_msg_<test>
Remove local #define net_<test> macros
Remove periods from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Remove periods from most formats
Coalesce long formats
Use printk_once
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net: free tx buffers when completions never arrive
In cases like when a pci device is disconnected on an error,
pending tx completions will never arrive. Unmap and free such
buffers in the tx cleanup path.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
also bug in de2104x.c was corrected:
for (i = 0; i < 32; i++) loop should be outside mc_list iteration.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added flags field to macvtap_queue to enable/disable processing of
virtio_net_hdr via IFF_VNET_HDR. This flag is checked to prepend virtio_net_hdr
in the receive path and process/skip virtio_net_hdr in the send path.
Original patch by Sridhar, further changes by Arnd.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for passing a macvtap file descriptor into
vhost-net, much like we already do for tun/tap.
Most of the new code is taken from the respective patch
in the tun driver and may get consolidated in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reworks the change done by the previous patch
in a more complete way.
The original macvtap code has a number of problems
resulting from the use of RCU for protecting the
access to struct macvtap_queue from open files.
This includes
- need for GFP_ATOMIC allocations for skbs
- potential deadlocks when copy_*_user sleeps
- inability to work with vhost-net
Changing the lifetime of macvtap_queue to always
depend on the open file solves all these. The
RCU reference simply moves one step down to
the reference on the macvlan_dev, which we
only need for nonblocking operations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 865a21a5e3 overwrote
commit a3aa18842a
Fix it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Convert formats like %8.8 to %08
Remove periods from formats
Coalesce long formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Checkpatch cleaning
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Checkpatch cleaning
Convert formats like 0x%08x to %#08x
Remove periods from formats
Coalesce long formats
Use print_hex_dump
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Remove periods from formats
Coalesce long formats
Use __func__
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Remove periods from formats
Coalesce long formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Convert struct bnx2x member msglevel to msg_enable for netif_msg_<foo> macros
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Coalesce long formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Remove periods from formats
Coalesce long formats
Coalesce some printks
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Remove periods from formats
Coalesce long formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Convert formats like %8.8 to %08
Remove periods from formats
Coalesce long formats
Use print_hex_dump
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Remove periods from formats
Coalesce long formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.108.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pushes phylib definitions out to phylib headers. For phy
IDs, this removes some code duplication.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylib presents the phy ID in a different format than the one tg3
has traditionally used. To highlight the distinction, this patch
prepends the tg3 native phy ID format with TG3.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reformats the SSID to phy ID table, replacing constants with
preprocessor definitions. This patch is also prep work for the
following patch, which will push line lengths beyond 80 chars.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy address will not change after it has been identified. Move the
discovery code to a location that only gets executed once.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an inverted "jumbo ring enable" test and jumps to the exit
if it succeeds. The change reduces the indent level of the remaining
code making it more readable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The STD part of this preprocessor definition is a bit of a misnomer.
This flag is a coarse control of the RGMII inband status facilities.
This patch renames the definition to be more accurate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 57765 asic partno entries for the path executed if VPD
is not present in NVRAM.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch loosens the restriction that the phylib interface must be up
and running to change the flow control parameters.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new offsets to the bootcode version extraction code to
support NVRAM format versions 4 and 5.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 57791 and 57795 to the list of devices that only
support 10 and 100 Mbps speeds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan noted that there is nothing in the code that would prevent
the compiler from delaying the access of the "mapping" member of the
newly arrived packet until much later. If this happened after the
skb = NULL assignment, it is possible for the driver to pass a bad
dma_addr value to pci_unmap_single(). To enforce this ordering, we need
a write memory barrier. The pairing read memory barrier already exists
in tg3_rx_prodring_xfer() under the comments starting with
"Ensure that updates to the...".
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds Linux Socket Filter support to
tun driver.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed whole t3_rx_mode structure and appropriate helpers cause they are no
longer needed.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_find_first() function instead of manual lookup.
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds device driver for Aeroflex Gaisler 10/100 and 10/100/1G Ethernet
MAC IP cores.
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduces CPU utilization significantly with sendfile for example.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes D-Link DGE-550T PCI ID (1186:4000) from the ipg
driver. The ipg driver is for IP2000-based cards and the DGE-550T is
a DL2000-based card. The driver loads and works for a few moments, but
once a real workload is applied it stops operating. The ipg driver
claimed this ID since it was introduced in 2.6.24 and it's forced many
users to blacklist it.
The correct driver for this hardware is the dl2k driver, which has been
claiming this PCI ID since the 2.4 days.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds half-duplex specific setup code (taken from SiS own GPL driver).
Without those, half-duplex connections are very unreliable, often
working on small transfers and failing after a while.
Signed-off-by: Riccardo Ghetta <birrachiara@tin.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated release version and date: 1.52.1-6 and 2010/02/16
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to the new firmware version (5.2.13).
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: Use the last unicast entry in CAM in bnx2x_test_int(). Relevant for 57710 only.
Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: Do not allow enabling LRO if disable_tpa=1.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: clean up MCP state in case of error in bnx2x_init_hw().
Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: Properly release allocated MSI-X/MSI vectors if ifup failed
due to lack of memory.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert from:
if (netif_msg_<foo>(priv))
dev_<level>(dev...
to
netif_<level>(priv, foo, dev...
Also convert a few:
if (i < REG_TIMEOUT) {
etc...
return ret;
}
to
if (i >= REG_TIMEOUT)
goto fail;
etc...
return ret;
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros are too similar to the dev_<level> equivalents
but take a usbnet * argument. Convert them to the recently
introduced netdev_<level> macros and remove the old macros.
The old macros had "\n" appended to the format string.
Add the "\n" to the converted uses.
Some existing uses of the dev<foo> macros in cdc_eem.c
probably mistakenly had trailing "\n". No "\n" added there.
Fix net1080 this/other log message inversion.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flush compl (compl with numfrags == 0; no data) is rcvd
from hw to indicate completion of RXQ destory operation. Fix
the RX path to not process it as RX data.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCC cmd is issued (via a netdev/ethtool op)
while the device is not open, the MCC CQ gets processed but the EQ
is not processed (as isr is not registered.) This can cause the EQ
to become full. So, while the device is not open, CQ must not be re-armed
to prevent EQ entries.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce unlikely() for skb alloc failure and vlanf checks...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some servers we see the cleaning of the RX queue finish before all
the loopback packets are sent out. This delay allows the queues to
settle before checking for successful completion.
Also, delay completion so link has time to come back up.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use local copy of current mac address when initializing. In bonding
testing we saw cases where dev_addr was out of data causing failover
errors.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was found with pings that were large enough to span multiple rx
buffers. The split frame logic handles this case nicely.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A userland command to set the LLTEMAC MAC address,
i.e. "ifconfig eth0 hw addr xx:yy:zz:pp:dd:qq",
results in a device address of 00:01:xx:yy:zz:pp.
Correct this.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LLTEMAC V1 cores place only received packet length in the app4 word.
V2 cores place additional information in app4.
Mask out the additional information when retrieving the packet length.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced a new function to do the mc list processing, makes code
clearer after transition.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the tx DMA mapping error handling code to
resemble e1000e/ixgbe.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change simplifies the code by setting RX_PTHRESH to 8 for
all devices, as it was unlikely that there was any advantage to
set it at 16 for earlier cards. Additionally TX_WTHRESH is
set to 1 for the 82576 NIC to improve performance by enabling
a minimal amount of write combining when writing back descriptors.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that igb_free_q_vectors is reused in
igb_alloc_q_vectors to handle the cleanup instead of unwinding
through the allocations.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an earlier version of igb_write_mc_addr_list() the vmolr register
was modified. This register is no longer accessed, although the variable
still exists. This patch removes it from the function.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change cleans up some instances where unsigned int and u32
were being used interchangeably, and cleans up hdr_len which
was being set to 0 twice.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves gso_segs into the buffer_info structure to avoid
a possible cache line miss in clean_tx_irq.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb_maybe_stop_tx() is extremely small and appears in several spots in
the tx hotpath. This change inlines the function for a possible
performance boost.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple statistics registers that are not meant to
be read when in SGMII/serdes mode. This patch adds a check to
verify mode before reading and updating these statistics.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SRRCTL.DROP_EN bit should only be set when we are supporting
multiple queues. This bit is meant to prevent head of line blocking
and is unnecessary in the single queue case.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to maintain similar performance between MSI-X and
legacy/MSI interrupts, this patch reduces the number of interrupts
when receiving small packets to 20K when in interrupt throttle
rate mode 3.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adaptive IFS support has been included in the igb driver since its
initial release, but it is not a feature on any igb NICs. This patch
removes it from the driver.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the rings are allocated seperately. As a
result we can allocate them on seperate nodes at some point in the future
if we so desire.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds calls to pci_save_state() immediately after
calls to pci_restore_state(). Due to a change in the behavior
of pci_restore_state() it is necessary to call pci_save_state()
to keep the state_saved flag. This patch is based on a similar
patch for ixgbe.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the behavior of the driver to power down the link
when the associated interface is down, unless management is enabled.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking the EEPROM APME state unnecessarily prevents the link from
shutting down. The standard power down routines should be
sufficient to determine whether the serdes link can power down
when going into D3.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this change ethtool will correctly report link status when
the interface is down. Currently ethtool reports the link as not
detected when the interface is down.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for wake-on-link/phy activity to the ethtool
interface.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change removes the use of itr_shift since a mac type call can be
used just as easily to identify the only HW that needs to have the itr
shifted.
In addition it removes two unecessary declarations of a q_vector
pointer from the initialization path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __percpu sparse annotations to net drivers.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
