Commit Graph

1047 Commits

Author SHA1 Message Date
NeilBrown
4bbf3771ca md: Relax minimum size restrictions on chunk_size.
Currently, the 'chunk_size' of an array must be at-least PAGE_SIZE.

This makes moving an array to a machine with a larger PAGE_SIZE, or
changing the kernel to use a larger PAGE_SIZE, can stop an array from
working.

For RAID10 and RAID4/5/6, this is non-trivial to fix as the resync
process works on whole pages at a time, and assumes them to be wholly
within a stripe.  For other raid personalities, this restriction is
not needed at all and can be dropped.

So remove the test on chunk_size from common can, and add it in just
the places where it is needed: raid10 and raid4/5/6.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
NeilBrown
d710e13812 md: remove space after function name in declaration and call.
Having
   function (args)
instead of
   function(args)

make is harder to search for calls of particular functions.
So remove all those spaces.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
NeilBrown
fb4d8c76e5 md: Remove unnecessary #includes, #defines, and function declarations.
A lot of cruft has gathered over the years.  Time to remove it.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll
ab5bd5cbc8 md: Convert remaining 1k representations in linear.c to sectors.
This patch renames hash_spacing and preshift to  spacing and
sector_shift respectively with the following change of semantics:

Case 1: (sizeof(sector_t) <= sizeof(u32)).
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

In this case, we have sector_shift = preshift = 0 and spacing =
2 * hash_spacing.

Hence, the index for the hash table which is computed by the new code
in which_dev() as sector / spacing equals the old value which was
(sector/2) / hash_spacing.

Note also that the value of nb_zone stays the same because both sz
and base double.

Case 2: (sizeof(sector_t) > sizeof(u32)).
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

(aka the shifting dance case). Here we have sector_shift = preshift +
1 and

spacing = 2 * hash_spacing

during the computation of nb_zone and curr_sector, but

spacing = hash_spacing

in which_dev() because in the last hunk of the patch for linear.c we
shift down conf->spacing (= 2 * hash_spacing) by one more bit than
in the old code.

Hence in the computation of nb_zone, sz and base have the same value
as before, so nb_zone is not affected. Also curr_sector in the next
hunk stays the same.

In which_dev() the hash table index is computed as

(sector >> sector_shift) / spacing

In view of sector_shift = preshift + 1 and spacing = hash_spacing,
this equals

((sector/2) >> preshift) / hash_spacing

which is the value computed by the old code.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll
23242fbb47 md: linear.c: Make two local variables sector-based.
This is a preparation for representing also the remaining fields of struct
linear_private_data as sectors.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll
6283815d18 md: linear: Represent dev_info->size and dev_info->offset in sectors.
Rename them to num_sectors and start_sector which is more descriptive.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll
451708d2a4 md: linear.c: Remove broken debug code.
conf->smallest_size is undefined since day one of the git repo..

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll
481d86c7eb md: linear.c: Remove pointless initialization of curr_offset.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Andre Noll
e61130228e md: linear.c: Fix typo in comment.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
NeilBrown
80268ee927 md: Don't try to set an array to 'read-auto' if it is already in that state.
'read-auto' is a variant of 'readonly' which will switch to writable
on the first write attempt.

Calling do_md_stop to set the array readonly when it is already readonly
returns an error.  So make sure not to do that.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
NeilBrown
ea43ddd849 md: Allow metadata_version to be updated for externally managed metadata.
For externally managed metadata, the 'metadata_version' sysfs
attribute is really just a channel for user-space programs to
communicate about how the array is being managed.
It can be useful for this to be changed while the array is active.

Normally changes to metadata_version are not permitted while the array
is active.  Change that so that if the metadata is externally managed,
the metadata_version can be changed to a different flavour of external
management.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:11 +11:00
Chris Webb
7d3c6f8717 md: Fix rdev_size_store with size == 0
Fix rdev_size_store with size == 0.
size == 0 means to use the largest size allowed by the
underlying device and is used when modifying an active array.

This fixes a regression introduced by
 commit d7027458d6

Cc: <stable@kernel.org>
Signed-off-by: Chris Webb <chris@arachsys.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:11 +11:00
Alan Jenkins
ce52aebd02 raid, fastboot: hide RAID autodetect option if MD is compiled as a module
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-12 08:25:14 -07:00
Arjan van de Ven
a364092a41 raid: make RAID autodetect default a KConfig option
RAID autodetect has the side effect of requiring synchronisation
of all device drivers, which can make the boot several seconds longer
(I've measured 7 on one of my laptops).... even for systems that don't
have RAID setup for the root filesystem (the only FS where this matters).

This patch makes the default for autodetect a config option; either way
the user can always override via the kernel command line.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: NeilBrown <neilb@suse.de>
2008-10-12 08:25:02 -07:00
Linus Torvalds
b0af205afb Merge git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
  dm: detect lost queue
  dm: publish dm_vcalloc
  dm: publish dm_table_unplug_all
  dm: publish dm_get_mapinfo
  dm: export struct dm_dev
  dm crypt: avoid unnecessary wait when splitting bio
  dm crypt: tidy ctx pending
  dm crypt: fix async inc_pending
  dm crypt: move dec_pending on error into write_io_submit
  dm crypt: remove inc_pending from write_io_submit
  dm crypt: tidy write loop pending
  dm crypt: tidy crypt alloc
  dm crypt: tidy inc pending
  dm exception store: use chunk_t for_areas
  dm exception store: introduce area_location function
  dm raid1: kcopyd should stop on error if errors handled
  dm mpath: remove is_active from struct dm_path
  dm mpath: use more error codes

Fixed up trivial conflict in drivers/md/dm-mpath.c manually.
2008-10-10 11:11:47 -07:00
Alasdair G Kergon
0c2322e4ce dm: detect lost queue
Detect and report buggy drivers that destroy their request_queue.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Stefan Raspl <raspl@linux.vnet.ibm.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
2008-10-10 13:37:13 +01:00
Mikulas Patocka
5416090426 dm: publish dm_vcalloc
Publish dm_vcalloc in include/linux/device-mapper.h because this function is
used by targets.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:12 +01:00
Mikulas Patocka
ea0ec64094 dm: publish dm_table_unplug_all
Publish dm_table_unplug_all in include/linux/device-mapper.h because this
function is used by targets.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:11 +01:00
Mikulas Patocka
89343da077 dm: publish dm_get_mapinfo
Publish dm_get_mapinfo in include/linux/device-mapper.h because this function
is used by targets.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:10 +01:00
Mikulas Patocka
82b1519b34 dm: export struct dm_dev
Split struct dm_dev in two and publish the part that other targets need in
include/linux/device-mapper.h.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:09 +01:00
Milan Broz
933f01d433 dm crypt: avoid unnecessary wait when splitting bio
Don't wait between submitting crypt requests for a bio unless
we are short of memory.

There are two situations when we must split an encrypted bio:
  1) there are no free pages;
  2) the new bio would violate underlying device restrictions
(e.g. max hw segments).

In case (2) we do not need to wait.

Add output variable to crypt_alloc_buffer() to distinguish between
these cases.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:08 +01:00
Milan Broz
c8081618a9 dm crypt: tidy ctx pending
Move the initialisation of ctx->pending into one place, at the
start of crypt_convert().

Introduce crypt_finished to indicate whether or not the encryption
is finished, for use in a later patch.

No functional change.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:08 +01:00
Milan Broz
4e59409891 dm crypt: fix async inc_pending
The pending reference count must be incremented *before* the async work is
queued to another thread, not after.  Otherwise there's a race if the
work completes and decrements the reference count before it gets incremented.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:07 +01:00
Milan Broz
6c031f41db dm crypt: move dec_pending on error into write_io_submit
Make kcryptd_crypt_write_io_submit() responsible for decrementing
the pending count after an error.

Also fixes a bug in the async path that forgot to decrement it.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:06 +01:00
Alasdair G Kergon
1e37bb8e55 dm crypt: remove inc_pending from write_io_submit
Make the caller reponsible for incrementing the pending count before calling
kcryptd_crypt_write_io_submit() in the non-async case to bring it into line
with the async case.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:05 +01:00
Milan Broz
fc5a5e9aa8 dm crypt: tidy write loop pending
Move kcryptd_crypt_write_convert_loop inside kcryptd_crypt_write_convert.
This change is needed for a later patch.

No functional change.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:04 +01:00
Milan Broz
dc440d1e56 dm crypt: tidy crypt alloc
Factor out crypt io allocation code.
Later patches will call it from another place.

No functional change.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:03 +01:00
Milan Broz
3e1a8bdd05 dm crypt: tidy inc pending
Move io pending to one place.

No functional change, usefull to simplify debugging.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:02 +01:00
Mikulas Patocka
fd14acf6fc dm exception store: use chunk_t for_areas
Change uint32_t into chunk_t to remove 32-bit limitation on the
number of chunks on systems with 64-bit sector numbers.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:01 +01:00
Mikulas Patocka
a481db7846 dm exception store: introduce area_location function
Move this logic to a function, because it will be reused later.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:37:00 +01:00
Jonathan Brassow
f7c83e2e47 dm raid1: kcopyd should stop on error if errors handled
dm-raid1 is setting the 'DM_KCOPYD_IGNORE_ERROR' flag unconditionally
when assigning kcopyd work.  kcopyd is responsible for copying an
assigned section of disk to one or more other disks.  The
'DM_KCOPYD_IGNORE_ERROR' flag affects kcopyd in the following way:

When not set:
kcopyd will immediately stop the copy operation when an error is
encountered.

When set:
kcopyd will try to proceed regardless of errors and try to continue
copying any remaining amount.

Since dm-raid1 tracks regions of the address space that are (or
are not) in sync and it now has the ability to handle these
errors, we can safely enable this optimization.  This optimization
is conditional on whether mirror error handling has been enabled.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:36:59 +01:00
Kiyoshi Ueda
6680073d3e dm mpath: remove is_active from struct dm_path
This patch moves 'is_active' from struct dm_path to struct pgpath
as it does not need exporting.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:36:58 +01:00
Benjamin Marzinski
01460f3520 dm mpath: use more error codes
This patch allows path errors from the multipath ctr function to
propagate up to userspace as errno values from the ioctl() call.

This is in response to
  https://www.redhat.com/archives/dm-devel/2008-May/msg00000.html
and
  https://bugzilla.redhat.com/show_bug.cgi?id=444421

The patch only lets through the errors that it needs to in order to
get the path errors from parse_path().

Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-10 13:36:57 +01:00
Denis ChengRq
6feef531f5 block: mark bio_split_pool static
Since all bio_split calls refer the same single bio_split_pool, the bio_split
function can use bio_split_pool directly instead of the mempool_t parameter;

then the mempool_t parameter can be removed from bio_split param list, and
bio_split_pool is only referred in fs/bio.c file, can be marked static.

Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:57:05 +02:00
Mike Anderson
224cb3e981 dm: Call blk_abort_queue on failed paths
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:14 +02:00
Tejun Heo
074a7aca7a block: move stats from disk to part0
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...

* part_stat_*() now updates part0 together if the specified partition
  is not part0.  ie. part_stat_*() are now essentially all_stat_*().

* {disk|all}_stat_*() are gone.

* part_round_stats() is updated similary.  It handles part0 stats
  automatically and disk_round_stats() is killed.

* part_{inc|dec}_in_fligh() is implemented which automatically updates
  part0 stats for parts other than part0.

* disk_map_sector_rcu() is updated to return part0 if no part matches.
  Combined with the above changes, this makes NULL special case
  handling in callers unnecessary.

* Separate stats show code paths for disk are collapsed into part
  stats show code paths.

* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()

While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:08 +02:00
Tejun Heo
0762b8bde9 block: always set bdev->bd_part
Till now, bdev->bd_part is set only if the bdev was for parts other
than part0.  This patch makes bdev->bd_part always set so that code
paths don't have to differenciate common handling.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:08 +02:00
Tejun Heo
b7db9956e5 block: move policy from disk to part0
Move disk->policy to part0->policy.  Implement and use get_disk_ro().

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:07 +02:00
Tejun Heo
ed9e198234 block: implement and use {disk|part}_to_dev()
Implement {disk|part}_to_dev() and use them to access generic device
instead of directly dereferencing {disk|part}->dev.  To make sure no
user is left behind, rename generic devices fields to __dev.

This is in preparation of unifying partition 0 handling with other
partitions.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:07 +02:00
Tejun Heo
c995905916 block: fix diskstats access
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters.  It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.

This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access).  diskstats access
should always be enclosed between the two functions.  As such, there's
no need for the versions which disables preemption.  They're removed
and double underbars ones are renamed to drop the underbars.  As an
extra argument is added, there's no danger of using the old version
unconverted.

disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.

This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others.  Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:06 +02:00
Tejun Heo
f331c0296f block: don't depend on consecutive minor space
* Implement disk_devt() and part_devt() and use them to directly
  access devt instead of computing it from ->major and ->first_minor.

  Note that all references to ->major and ->first_minor outside of
  block layer is used to determine devt of the disk (the part0) and as
  ->major and ->first_minor will continue to represent devt for the
  disk, converting these users aren't strictly necessary.  However,
  convert them for consistency.

* Implement disk_max_parts() to avoid directly deferencing
  genhd->minors.

* Update bdget_disk() such that it doesn't assume consecutive minor
  space.

* Move devt computation from register_disk() to add_disk() and make it
  the only one (all other usages use the initially determined value).

These changes clean up the code and will help disk->part dereference
fix and extended block device numbers.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:05 +02:00
Jens Axboe
5b99c2ffa9 block: make bi_phys_segments an unsigned int instead of short
raid5 can overflow with more than 255 stripes, and we can increase it
to an int for free on both 32 and 64-bit archs due to the padding.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:03 +02:00
Jens Axboe
960e739d9e block: raid fixups for removal of bi_hw_segments
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:03 +02:00
Mikulas Patocka
5df97b91b5 drop vmerge accounting
Remove hw_segments field from struct bio and struct request. Without virtual
merge accounting they have no purpose.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:03 +02:00
Chandra Seetharaman
7253a33434 dm mpath: add missing path switching locking
Moving the path activation to workqueue along with scsi_dh patches introduced
a race. It is due to the fact that the current_pgpath (in the multipath data
structure) can be modified if changes happen in any of the paths leading to
the lun. If the changes lead to current_pgpath being set to NULL, then it
leads to the invalid access which results in the panic below.

This patch fixes that by storing the pgpath to activate in the multipath data
structure and properly protecting it.

Note that if activate_path is called twice in succession with different pgpath,
with the second one being called before the first one is done, then activate
path will be called twice for the second pgpath, which is fine.

Unable to handle kernel paging request for data at address 0x00000020
Faulting instruction address: 0xd000000000aa1844
cpu 0x1: Vector: 300 (Data Access) at [c00000006b987a80]
    pc: d000000000aa1844: .activate_path+0x30/0x218 [dm_multipath]
    lr: c000000000087a2c: .run_workqueue+0x114/0x204
    sp: c00000006b987d00
   msr: 8000000000009032
   dar: 20
 dsisr: 40000000
  current = 0xc0000000676bb3f0
  paca    = 0xc0000000006f3680
    pid   = 2528, comm = kmpath_handlerd
enter ? for help
[c00000006b987da0] c000000000087a2c .run_workqueue+0x114/0x204
[c00000006b987e40] c000000000088b58 .worker_thread+0x120/0x144
[c00000006b987f00] c00000000008ca70 .kthread+0x78/0xc4
[c00000006b987f90] c000000000027cc8 .kernel_thread+0x4c/0x68

Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-01 14:39:27 +01:00
Mikulas Patocka
b01cd5ac43 dm: cope with access beyond end of device in dm_merge_bvec
If for any reason dm_merge_bvec() is given an offset beyond the end of the
device, avoid an oops and always allow one page to be added to an empty bio.
We'll reject the I/O later after the bio is submitted.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-01 14:39:24 +01:00
Mikulas Patocka
5037108acd dm: always allow one page in dm_merge_bvec
Some callers assume they can always add at least one page to an empty bio,
so dm_merge_bvec should not return 0 in this case: we'll reject the I/O
later after the bio is submitted.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-10-01 14:39:17 +01:00
NeilBrown
9744197c3d md: Don't wait UNINTERRUPTIBLE for other resync to finish
When two md arrays share some block device (e.g each uses different
partitions on the one device), a resync of one array will wait for
the resync on the other to finish.

This can be a long time and as it currently waits TASK_UNINTERRUPTIBLE,
the softlockup code notices and complains.

So use TASK_INTERRUPTIBLE instead and make sure to flush signals
before calling schedule.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-09-19 11:49:54 +10:00
NeilBrown
b2d2c4cead Fix problem with waiting while holding rcu read lock in md/bitmap.c
A recent patch to protect the rdev list with rcu locking leaves us
with a problem because we can sleep on memalloc while holding the
rcu lock.

The rcu lock is only needed while walking the linked list as
uninteresting devices (failed or spares) can be removed at any time.

So only take the rcu lock while actually walking the linked list.
Take a refcount on the rdev during the time when we drop the lock
and do the memalloc to start IO.
When we return to the locked code, all the interesting devices
on the list will not have moved, so we can simply use
list_for_each_continue_rcu to pick up where we left off.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-09-01 12:48:13 +10:00
NeilBrown
271f5a9b8f Remove invalidate_partition call from do_md_stop.
When stopping an md array, or just switching to read-only, we
currently call invalidate_partition while holding the mddev lock.
The main reason for this is probably to ensure all dirty buffers
are flushed (invalidate_partition calls fsync_bdev).

However if any dirty buffers are found, it will almost certainly cause
a deadlock as starting writeout will require an update to the
superblock, and performing that updates requires taking the mddev
lock - which is already held.

This deadlock can be demonstrated by running "reboot -f -n" with
a root filesystem on md/raid, and some dirty buffers in memory.

All other calls to stop an array should already happen after a flush.
The normal sequence is to stop using the array (e.g. umount) which
will cause __blkdev_put to call sync_blockdev.  Then open the
array and issue the STOP_ARRAY ioctl while the buffers are all still
clean.

So this invalidate_partition is normally a no-op, except for one case
where it will cause a deadlock.

So remove it.

This patch possibly addresses the regression recored in
   http://bugzilla.kernel.org/show_bug.cgi?id=11460
and
   http://bugzilla.kernel.org/show_bug.cgi?id=11452

though it isn't yet clear how it ever worked.


Signed-off-by: NeilBrown <neilb@suse.de>
2008-09-01 12:32:52 +10:00
Dan Williams
56ac36d722 md: cancel check/repair requests when recovery is needed
If a 'repair' is requested when an array is in a position to 'recover' raid1
will perform the repair while md believes a recovery is happening.  Address
this at both ends, i.e. cancel check/repair requests upon detecting a
recover condition and do not call ->spare_active after completing a
check/repair.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-08-07 10:02:47 -07:00
NeilBrown
0310fa216d Allow raid10 resync to happening in larger chunks.
The raid10 resync/recovery code currently limits the amount of
in-flight resync IO to 2Meg.  This was copied from raid1 where
it seems quite adequate.  However for raid10, some layouts require
a bit of seeking to perform a resync, and allowing a larger buffer
size means that the seeking can be significantly reduced.

There is probably no real need to limit the amount of in-flight
IO at all.  Any shortage of memory will naturally reduce the
amount of buffer space available down to a set minimum, and any
concurrent normal IO will quickly cause resync IO to back off.

The only problem would be that normal IO has to wait for all resync IO
to finish, so a very large amount of resync IO could cause unpleasant
latency when normal IO starts up.

So: increase RESYNC_DEPTH to allow 32Meg of buffer (if memory is
available) which seems to be a good amount.  Also reduce the amount
of memory reserved as there is no need to keep 2Meg just for resync if
memory is tight.

Thanks to Keld for the suggestion.

Cc: Keld Jørn Simonsen <keld@dkuug.dk>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-05 15:56:32 +10:00
NeilBrown
c89a8eee61 Allow faulty devices to be removed from a readonly array.
Removing faulty devices from an array is a two stage process.
First the device is moved from being a part of the active array
to being similar to a spare device.  Then it can be removed
by a request from user space.

The first step is currently not performed for read-only arrays,
so the second step can never succeed.

So allow readonly arrays to remove failed devices (which aren't
blocked).

Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-05 15:56:32 +10:00
NeilBrown
ac4090d24c Don't let a blocked_rdev interfere with read request in raid5/6
When we have externally managed metadata, we need to mark a failed
device as 'Blocked' and not allow any writes until that device
have been marked as faulty in the metadata and the Blocked flag has
been removed.

However it is perfectly OK to allow read requests when there is a
Blocked device, and with a readonly array, there may not be any
metadata-handler watching for blocked devices.

So in raid5/raid6 only allow a Blocked device to interfere with
Write request or resync.  Read requests go through untouched.

raid1 and raid10 already differentiate between read and write
properly.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-05 15:56:32 +10:00
NeilBrown
dba034eef2 Fail safely when trying to grow an array with a write-intent bitmap.
We cannot currently change the size of a write-intent bitmap.
So if we change the size of an array which has such a bitmap, it
tries to set bits beyond the end of the bitmap.

For now, simply reject any request to change the size of an array
which has a bitmap.  mdadm can remove the bitmap and add a new one
after the array has changed size.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-05 15:56:32 +10:00
NeilBrown
2b25000bf5 Restore force switch of md array to readonly at reboot time.
A recent patch allowed do_md_stop to know whether it was being called
via an ioctl or not, and thus where to allow for an extra open file
descriptor when checking if it is in use.
This broke then switch to readonly performed by the shutdown notifier,
which needs to work even when the array is still (apparently) active
(as md doesn't get told when the filesystem becomes readonly).

So restore this feature by pretending that there can be lots of
file descriptors open, but we still want do_md_stop to switch to
readonly.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-05 15:56:31 +10:00
NeilBrown
19052c0e85 Make writes to md/safe_mode_delay immediately effective.
If we reduce the 'safe_mode_delay', it could still wait for the old
delay to completely expire before doing anything about safe_mode.
Thus the effect if the change is delayed.

To make the effect more immediate, run the timeout function
immediately if the delay was reduced.  This may cause it to run
slightly earlier that required, but that is the safer option.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-05 15:56:31 +10:00
Linus Torvalds
1e24b15b26 Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
  md: raid10: wake up frozen array
  md: do not count blocked devices as spares
  md: do not progress the resync process if the stripe was blocked
  md: delay notification of 'active_idle' to the recovery thread
  md: fix merge error
  md: move async_tx_issue_pending_all outside spin_lock_irq
2008-08-01 11:56:07 -07:00
Linus Torvalds
b17b3d479c Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  md: the bitmap code needs to use blk_plug_device_unlocked()
  block: add a blk_plug_device_unlocked() that grabs the queue lock
2008-08-01 11:46:00 -07:00
Jens Axboe
93769f5807 md: the bitmap code needs to use blk_plug_device_unlocked()
It doesn't hold the queue lock, so it's both racey on the queue flags
and thus spews a warning.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-08-01 20:32:31 +02:00
Al Viro
d5686b444f [PATCH] switch mtd and dm-table to lookup_bdev()
No need to open-code it...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2008-08-01 11:25:31 -04:00
Arthur Jones
388667bed5 md: raid10: wake up frozen array
When rescheduling a bio in raid10, we wake up
the md thread, but if the array is frozen, this
will have no effect.  This causes the array to
remain frozen for eternity.  We add a wake_up
to allow the array to de-freeze.  This code is
nearly identical to the raid1 code, which has
this fix already.

Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-01 12:55:14 +10:00
Dan Williams
e542713529 md: do not count blocked devices as spares
remove_and_add_spares() assumes that failed devices have been hot-removed
from the array.  Removal is skipped in the 'blocked' case so do not count a
device in this state as 'spare'.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-28 17:52:44 -07:00
Dan Williams
df10cfbc4d md: do not progress the resync process if the stripe was blocked
handle_stripe will take no action on a stripe when waiting for userspace
to unblock the array, so do not report completed sectors.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-28 17:52:37 -07:00
Hannes Reinecke
ae11b1b36d [SCSI] scsi_dh: attach to hardware handler from dm-mpath
multipath keeps a separate device table which may be
more current than the built-in one.
So we should make sure to always call ->attach whenever
a multipath map with hardware handler is instantiated.
And we should call ->detach on removal, too.

[sekharan: update as per comments from agk]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-26 15:14:53 -04:00
Dan Williams
d8e64406a0 md: delay notification of 'active_idle' to the recovery thread
sysfs_notify might sleep, so do not call it from md_safemode_timeout.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-23 13:09:48 -07:00
Dan Williams
2339788376 md: fix merge error
The original STRIPE_OP_IO removal patch had the following hunk:

-               for (i = conf->raid_disks; i--; ) {
+               for (i = conf->raid_disks; i--; )
                        set_bit(R5_Wantwrite, &sh->dev[i].flags);
-                       if (!test_and_set_bit(STRIPE_OP_IO, &sh->ops.pending))
-                               sh->ops.count++;
-               }

However it appears the hunk became broken after merging:
-               for (i = conf->raid_disks; i--; ) {
+               for (i = conf->raid_disks; i--; )
                        set_bit(R5_Wantwrite, &sh->dev[i].flags);
                        set_bit(R5_LOCKED, &dev->flags);
                        s.locked++;
-                       if (!test_and_set_bit(STRIPE_OP_IO, &sh->ops.pending))
-                               sh->ops.count++;
-               }

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-23 13:09:45 -07:00
Dan Williams
c9f21aaff1 md: move async_tx_issue_pending_all outside spin_lock_irq
Some dma drivers need to call spin_lock_bh in their device_issue_pending
routines.  This change avoids:

WARNING: at kernel/softirq.c:136 local_bh_enable_ip+0x3a/0x85()

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-23 12:05:51 -07:00
Linus Torvalds
b7e6f62fe2 Merge git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
  dm crypt: add merge
  dm table: remove merge_bvec sector restriction
  dm: linear add merge
  dm: introduce merge_bvec_fn
  dm snapshot: use per device mempools
  dm snapshot: fix race during exception creation
  dm snapshot: track snapshot reads
  dm mpath: fix test for reinstate_path
  dm mpath: return parameter error
  dm io: remove struct padding
  dm log: make dm_dirty_log init and exit static
  dm mpath: free path selector on invalid args
2008-07-21 10:30:10 -07:00
Linus Torvalds
8a392625b6 Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md: (52 commits)
  md: Protect access to mddev->disks list using RCU
  md: only count actual openers as access which prevent a 'stop'
  md: linear: Make array_size sector-based and rename it to array_sectors.
  md: Make mddev->array_size sector-based.
  md: Make super_type->rdev_size_change() take sector-based sizes.
  md: Fix check for overlapping devices.
  md: Tidy up rdev_size_store a bit:
  md: Remove some unused macros.
  md: Turn rdev->sb_offset into a sector-based quantity.
  md: Make calc_dev_sboffset() return a sector count.
  md: Replace calc_dev_size() by calc_num_sectors().
  md: Make update_size() take the number of sectors.
  md: Better control of when do_md_stop is allowed to stop the array.
  md: get_disk_info(): Don't convert between signed and unsigned and back.
  md: Simplify restart_array().
  md: alloc_disk_sb(): Return proper error value.
  md: Simplify sb_equal().
  md: Simplify uuid_equal().
  md: sb_equal(): Fix misleading printk.
  md: Fix a typo in the comment to cmd_match().
  ...
2008-07-21 10:29:12 -07:00
Milan Broz
d41e26b901 dm crypt: add merge
This patch implements biovec merge function for crypt target.

If the underlying device has merge function defined, call it.
If not, keep precomputed value.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:40 +01:00
Milan Broz
9980c638a6 dm table: remove merge_bvec sector restriction
Remove max_sector restriction - merge function replaced it.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:39 +01:00
Milan Broz
7bc3447b69 dm: linear add merge
This patch implements biovec merge function for linear target.

If the underlying device has merge function defined, call it.
If not, keep precomputed value.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:38 +01:00
Milan Broz
f6fccb1213 dm: introduce merge_bvec_fn
Introduce a bvec merge function for device mapper devices
for dynamic size restrictions.

This code ensures the requested biovec lies within a single
target and then calls a target-specific function to check
against any constraints imposed by underlying devices.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:37 +01:00
Mikulas Patocka
92e868122e dm snapshot: use per device mempools
Change snapshot per-module mempool to per-device mempool.

Per-module mempools could cause a deadlock if multiple
snapshot devices are stacked above each other.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:35 +01:00
Mikulas Patocka
a8d41b59f3 dm snapshot: fix race during exception creation
Fix a race condition that returns incorrect data when a write causes an
exception to be allocated whilst a read is still in flight.

The race condition happens as follows:
* A read to non-reallocated sector in the snapshot is submitted so that the
  read is routed to the original device.
* A write to the original device is submitted. The write causes an exception
  that reallocates the block.  The write proceeds.
* The original read is dequeued and reads the wrong data.

This race can be triggered with CFQ scheduler and one thread writing and
multiple threads reading simultaneously.

(This patch relies upon the earlier dm-kcopyd-per-device.patch to avoid a
deadlock.)

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:34 +01:00
Mikulas Patocka
cd45daffd1 dm snapshot: track snapshot reads
Whenever a snapshot read gets mapped through to the origin, track it in
a per-snapshot hash table indexed by chunk number, using memory allocated
from a new per-snapshot mempool.

We need to track these reads to avoid race conditions which will be fixed
by patches that follow.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:32 +01:00
Alasdair G Kergon
def052d21c dm mpath: fix test for reinstate_path
Fix test for reinstate_path method before attempting to use it.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Julia Lawall <julia@diku.dk>
2008-07-21 12:00:31 +01:00
Mikulas Patocka
148acff615 dm mpath: return parameter error
Return a specific error message if there are an invalid number of multipath
arguments.

This invalid command returns an "Unknown error" because the ti->error field is
not set

dmsetup create --table '0 2 multipath 0 0 1 1 round-robin 0 1 1 /dev/sdh' mpath0

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:30 +01:00
Richard Kennedy
6ae2fa6718 dm io: remove struct padding
Rearrange struct dm_io.
Shrinks size from 40 -> 32 allowing more objects/slab.

Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:28 +01:00
Adrian Bunk
c8da2f8dd8 dm log: make dm_dirty_log init and exit static
dm_dirty_log_{init,exit}() can now become static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:27 +01:00
Mikulas Patocka
371b2e348b dm mpath: free path selector on invalid args
Free path selector if the arguments are invalid.

This command (note that it is invalid) causes reference leak on module
"dm_round_robin" and prevents the module from being removed.

dmsetup create --table '0 2 multipath 0 0 1 1 round-robin /dev/sdh' mpath0

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-07-21 12:00:24 +01:00
NeilBrown
4b80991c6c md: Protect access to mddev->disks list using RCU
All modifications and most access to the mddev->disks list are made
under the reconfig_mutex lock.  However there are three places where
the list is walked without any locking.  If a reconfig happens at this
time, havoc (and oops) can ensue.

So use RCU to protect these accesses:
  - wrap them in rcu_read_{,un}lock()
  - use list_for_each_entry_rcu
  - add to the list with list_add_rcu
  - delete from the list with list_del_rcu
  - delay the 'free' with call_rcu rather than schedule_work

Note that export_rdev did a list_del_init on this list.  In almost all
cases the entry was not in the list anymore so it was a no-op and so
safe.  It is no longer safe as after list_del_rcu we may not touch
the list_head.
An audit shows that export_rdev is called:
  - after unbind_rdev_from_array, in which case the delete has
     already been done,
  - after bind_rdev_to_array fails, in which case the delete isn't needed.
  - before the device has been put on a list at all (e.g. in
      add_new_disk where reading the superblock fails).
  - and in autorun devices after a failure when the device is on a
      different list.

So remove the list_del_init call from export_rdev, and add it back
immediately before the called to export_rdev for that last case.

Note also that ->same_set is sometimes used for lists other than
mddev->list (e.g. candidates).  In these cases rcu is not needed.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 17:05:25 +10:00
NeilBrown
f2ea68cf42 md: only count actual openers as access which prevent a 'stop'
Open isn't the only thing that increments ->active.  e.g. reading
/proc/mdstat will increment it briefly.  So to avoid false positives
in testing for concurrent access, introduce a new counter that counts
just the number of times the md device it open.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 17:05:25 +10:00
Andre Noll
d6e2215052 md: linear: Make array_size sector-based and rename it to array_sectors.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 17:05:25 +10:00
Andre Noll
f233ea5c9e md: Make mddev->array_size sector-based.
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 17:05:22 +10:00
Andre Noll
15f4a5fdf3 md: Make super_type->rdev_size_change() take sector-based sizes.
Also, change the type of the size parameter from unsigned long long to
sector_t and rename it to num_sectors.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 14:42:12 +10:00
Andre Noll
d07bd3bcc4 md: Fix check for overlapping devices.
The checks in overlaps() expect all parameters either in block-based
or sector-based quantities. However, its single caller passes two
rdev->data_offset arguments as well as two rdev->size arguments, the
former being sector counts while the latter are measured in 1K blocks.

This could cause rdev_size_store() to accept an invalid size from user
space. Fix it by passing only sector-based quantities to overlaps().

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 14:42:07 +10:00
Neil Brown
d7027458d6 md: Tidy up rdev_size_store a bit:
- used strict_strtoull in place of simple_strtoull
 - use my_mddev in place of rdev->mddev (they have the same value)
and more significantly,
 - don't adjust mddev->size to fit, rather reject changes which make
   rdev->size smaller than mddev->size

Adjusting mddev->size is a hangover from bind_rdev_to_array which
does a similar thing.  But it really is a better design to insist that
mddev->size is set as required, then the rdev->sizes are set to allow
for that.  The previous way invites confusion.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 14:22:18 +10:00
Linus Torvalds
89a93f2f48 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
  [SCSI] scsi_dh: fix kconfig related build errors
  [SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
  [SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
  [SCSI] make struct scsi_{host,target}_type static
  [SCSI] fix locking in host use of blk_plug_device()
  [SCSI] zfcp: Cleanup external header file
  [SCSI] zfcp: Cleanup code in zfcp_erp.c
  [SCSI] zfcp: zfcp_fsf cleanup.
  [SCSI] zfcp: consolidate sysfs things into one file.
  [SCSI] zfcp: Cleanup of code in zfcp_aux.c
  [SCSI] zfcp: Cleanup of code in zfcp_scsi.c
  [SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
  [SCSI] zfcp: Small QDIO cleanups
  [SCSI] zfcp: Adapter reopen for large number of unsolicited status
  [SCSI] zfcp: Fix error checking for ELS ADISC requests
  [SCSI] zfcp: wait until adapter is finished with ERP during auto-port
  [SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
  [SCSI] sg: Add target reset support
  [SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
  [SCSI] sd: Move scsi_disk() accessor function to sd.h
  ...
2008-07-15 18:58:04 -07:00
Chandra Seetharaman
fe9233fb69 [SCSI] scsi_dh: fix kconfig related build errors
Do not automatically "select" SCSI_DH for dm-multipath. If SCSI_DH
doesn't exist,just do not allow  hardware handlers to be used.

Handle SCSI_DH being a module also. Make sure it doesn't allow DM_MULTIPATH
to be compiled in when SCSI_DH is a module.

[jejb: added comment for Kconfig syntax]
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-15 09:16:43 -05:00
Linus Torvalds
dddec01eb8 Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (37 commits)
  splice: fix generic_file_splice_read() race with page invalidation
  ramfs: enable splice write
  drivers/block/pktcdvd.c: avoid useless memset
  cdrom: revert commit 22a9189 (cdrom: use kmalloced buffers instead of buffers on stack)
  scsi: sr avoids useless buffer allocation
  block: blk_rq_map_kern uses the bounce buffers for stack buffers
  block: add blk_queue_update_dma_pad
  DAC960: push down BKL
  pktcdvd: push BKL down into driver
  paride: push ioctl down into driver
  block: use get_unaligned_* helpers
  block: extend queue_flag bitops
  block: request_module(): use format string
  Add bvec_merge_data to handle stacked devices and ->merge_bvec()
  block: integrity flags can't use bit ops on unsigned short
  cmdfilter: extend default read filter
  sg: fix odd style (extra parenthesis) introduced by cmd filter patch
  block: add bounce support to blk_rq_map_user_iov
  cfq-iosched: get rid of enable_idle being unused warning
  allow userspace to modify scsi command filter on per device basis
  ...
2008-07-14 13:15:14 -07:00
Andre Noll
0f420358e3 md: Turn rdev->sb_offset into a sector-based quantity.
Rename it to sb_start to make sure all users have been converted.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-07-11 22:02:23 +10:00
Andre Noll
b73df2d3d6 md: Make calc_dev_sboffset() return a sector count.
As BLOCK_SIZE_BITS is 10 and

	MD_NEW_SIZE_SECTORS(2 * x) = 2 * NEW_SIZE_BLOCKS(x),

the return value of calc_dev_sboffset() doubles. Fix up all three
callers accordingly.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-07-11 22:02:23 +10:00
Andre Noll
e7debaa495 md: Replace calc_dev_size() by calc_num_sectors().
Number of sectors is the preferred unit for sizes of raid devices,
so change calc_dev_size() so that it returns this unit instead of
the number of 1K blocks.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-07-11 22:02:23 +10:00
Andre Noll
d71f9f88d7 md: Make update_size() take the number of sectors.
Changing the internal representations of sizes of raid devices
from 1K blocks to sector counts (512B units) is desirable because
it allows to get rid of many divisions/multiplications and unnecessary
casts that are present in the current code.

This patch is a first step in this direction. It replaces the old
1K-based "size" argument of update_size() by "num_sectors" and
fixes up its two callers.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-07-11 22:02:22 +10:00
Neil Brown
df5b20cf68 md: Better control of when do_md_stop is allowed to stop the array.
do_md_stop check the number of active users before allowing the array
to be stopped.
Two problems:
  1/ it assumes the request is coming through an open file descriptor
     (via ioctl) so it allows for that.  This is not always the case.
  2/ it doesn't do the check it the array hasn't been activated.
     This is not good for cases when we use an inactive array to hold
     some devices in a container.

Signed-off-by: Neil Brown <neilb@suse.de>
2008-07-11 22:02:22 +10:00
Andre Noll
26ef379f53 md: get_disk_info(): Don't convert between signed and unsigned and back.
The current code copies a signed int from user space, converts it to
unsigned and passes the unsigned value to find_rdev_nr() which expects
a signed value. Simply pass the signed value from user space directly.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-07-11 22:02:21 +10:00
Andre Noll
80fab1d77b md: Simplify restart_array().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-07-11 22:02:21 +10:00
Andre Noll
ebc2433728 md: alloc_disk_sb(): Return proper error value.
If alloc_page() fails, ENOMEM is a more suitable error value
than EINVAL.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-07-11 22:02:20 +10:00