Commit Graph

515 Commits

Author SHA1 Message Date
Rafael J. Wysocki
ce9b2b0abb Resume from RAM on HPC nx6325 broken
generic_ide_resume() should check if dev->driver is not NULL before applying
to_ide_driver() to it.  Fix that.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-16 02:24:43 +02:00
Peer Chen
c1183a3345 ide: Add the MCP73/77 support to PATA driver
Add the MCP73/MCP77 support to PATA driver.

bart: Added amd74xx_chipsets[] and amd_pci_tbl[] entries.
bart: Bumped driver version.

Signed-off-by: Peer Chen <peerchen@gmail.com>
Cc: Alan Cox <alan@redhat.com>,
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:32 +02:00
Sergei Shtylyov
278978e953 hpt366: disallow Ultra133 for HPT374
Eliminate UltraATA/133 support for HPT374 -- the chip isn't capable of this mode
according to the manual, and doesn't even seem to tolerate 66 MHz DPLL clock...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Geller Sandor <wildy@petra.hos.u-szeged.hu>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:32 +02:00
Jiri Slaby
ea30759643 ide: generic IDE PCI driver, add another device exception
generic IDE PCI driver, add another device exception

This device is char device and is grabbed by generic ide driver:
00:0b.0 Class ffff: National Semiconductor Corporation 87410 IDE (rev ff) (prog-if ff)
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-

Disallow generic IDE PCI driver to grab it by adding next condition. Also
consolidate exceptions to one bigger 'switch (dev->vendor)'.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Ingo Korb <ml@akana.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:31 +02:00
Lee Trager
0d2157f78d ide: HPA detect from resume
Currently when system which have HPA require HPA to be detected and
disabled upon resume from RAM or disk. The current IDE drivers do not do
this nor does libata (obviously it since it doesn't support HPA yet).

I have implemented this into the current IDE drivers and it has been
tested by many others since 7/15/2006 in bug number 6840:

	http://bugzilla.kernel.org/show_bug.cgi?id=6840

and it has been confirmed to work fine with no problems.

bart: added drv != NULL check to generic_ide_suspend()

From: Lee Trager <lt73@cs.drexel.edu>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:30 +02:00
Bartlomiej Zolnierkiewicz
0380dad45e it821x: RAID mode fixes
The DMA support for RAID mode broke after:

	commit 71ef51cc17
	Author: Jens Axboe <axboe@suse.de>
	Date:   Fri Jul 28 09:02:17 2006 +0200

	    [PATCH] it821x: fix ide dma setup bug

	    Only enable dma for a valid speed setting.

	    Signed-off-by: Jens Axboe <axboe@suse.de>

	commit 0a8348d086
	Author: Jens Axboe <axboe@suse.de>
	Date:   Fri Jul 28 08:58:26 2006 +0200

	    [PATCH] ide: if the id fields looks screwy, disable DMA

	    It's the safer choice. Originally due to a bug in itx821x, but a
	    generally sound thing to do.

	    Signed-off-by: Jens Axboe <axboe@suse.de>

However it worked by pure luck before Jens' fixes: bogus ide_dma_enable()
usage in it821x driver combined with loosy check in ide_dma_verbose() allowed
the hardware to operate in DMA mode.  When these problems were fixed the DMA
support broke...

The source root for the regression turned out to be that the it821x.c code
was clearing too much of id->field_valid.  The IDE core code was using the
original value of id->field_valid to do the tuning but later DMA got disabled
in ide_dma_verbose() because of the incorrect id->field_valid fixup.  Fix it.

While at it:

* Do fixup() after probing the drives but before tuning them (which is also
  OK w.r.t. ide_undecoded_slave() fixup).  This change fixes device IDENTIFY
  data to be consistent before/after the tuning and allows us to remove extra
  re-tuning of drives from it821x_fixups().

* Fake MWDMA0 enabled/supported bits in IDENTIFY data if the device has
  DMA capable bit set (this is just to tell the IDE core that DMA is
  supported since it821x firmware takes care of DMA mode programming).

* Don't touch timing registers and don't program transfer modes on devices
  et all when in RAID mode - depend solely on firmware to do the tuning
  (as suggested by Alan Cox and done in libata pata_it821x driver).

Thanks for testing the patch goes out to Thomas Kuther.

Cc: Thomas Kuther <gimpel@sonnenkinder.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:29 +02:00
Bartlomiej Zolnierkiewicz
1abb8a8b84 serverworks: fix CSB6 tuning logic
Problem noticed by Joe Zbiciak, see

	http://kerneltrap.org/node/8252

for details.

On CSB6 the driver is using BIOS settings and not programming DMA/PIO timings
itself.  However the logic was completely broken and resulted in wrong timings
being silently allowed (instead of being corrected by the driver).

This bug would explain some data corruption/timeout issues with Serverworks
MegaIDE in RAID mode that Alan Cox has fixed recently with:

http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=2074a106f52b6371885afbd714e929d60d0e3f64

For 2.6.23 we may be better off with completely switching the driver to always
programming timings (libata pata_serverworks.c driver is doing things this way
and there were no problems reported so far) but for 2.6.22 lets fix the bug
in the simplest and the least intrusive way.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:28 +02:00
Bartlomiej Zolnierkiewicz
ed84fad500 serverworks: remove crappy code
Remove crappy code noticed by Linus, see

	http://lkml.org/lkml/2007/5/23/476

for details.

While at it simplify logic a bit.

There should be no functionality changes caused by this patch.

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:27 +02:00
Andrew Morton
585a2858b9 ide serverworks warning fixes
gcc-4.3:

drivers/ide/pci/serverworks.c: In function 'svwks_tune_chipset':
drivers/ide/pci/serverworks.c:176: warning: overflow in implicit constant conversion
drivers/ide/pci/serverworks.c:190: warning: overflow in implicit constant conversion
drivers/ide/pci/serverworks.c:211: warning: overflow in implicit constant conversion
drivers/ide/pci/serverworks.c:212: warning: overflow in implicit constant conversion

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:39 +02:00
Junio C Hamano
5a6248cac2 Match DMA blacklist entries between ide-dma.c and libata-core.c
There are a few entries in ata_device_blacklist[] in libata-core.c
marked with HORKAGE_NODMA but are missing from drive_blacklist[]
in ide-dma.c.  This patch makes the lists in sync.

Also remove a duplicated entry for "SanDisk SDP3B-64".

Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:38 +02:00
Mika Kukkonen
39c98c4212 Add two missing chipsets to drivers/ide/ide-proc.c
Compiling with '-Wswitch-enum' I noticed following:

  CC      drivers/ide/ide-proc.o
drivers/ide/ide-proc.c: In function ‘proc_ide_read_imodel’:
drivers/ide/ide-proc.c:54: warning: enumeration value ‘ide_etrax100’ not handled in switch
drivers/ide/ide-proc.c:54: warning: enumeration value ‘ide_acorn’ not handled in switch

How about the following patch?

Signed-off-by: Mika Kukkonen <mikukkon@iki.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:38 +02:00
Alan Cox
2074a106f5 ide/pci/serverworks.c: Fix corruption/timeouts with MegaIDE
It turns out from customer reports to Red Hat and some PCI dumps that the
MegaIDE in RAID mode doesn't provide the drive tuning data that the
serverworks driver expects but sometimes does provide something that
fools the code.

For the RAID class case skip the oem setup and don't trust the BIOS data.
We then tune from scratch and this sorts it out. (This has been confirmed
on an afflicted IBM blade)

[libata serverworks.c never trusts the BIOS in the first place so is
accidentally immune]

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:38 +02:00
Henry Su
6c6a2a8d20 add the IDE device ID for ATI SB700
Add the IDE device ID to atiixp_pci_tbl struct in atiixp.c for ATI SB700.

From: Henry Su <henry.su@amd.com>
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:37 +02:00
Jan Engelhardt
e0ff9cd12a Use menuconfig objects: IDE
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.

Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Alan Cox
640b31bf12 sl82c105: Switch to ref counting API
Not sure how this one got missed in the great purge some time ago but it did.

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz
122ab0887c ide: remove ide_use_dma()
ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz
3649c06e66 ide: add missing validity checks for identify words 62 and 63
Check validity of identify words 62 and 63 before using them in
ide_get_mode_mask().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz
4728d546d7 ide: remove ide_dma_enable()
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Sergei Shtylyov
46cedc9b77 sl82c105: add speedproc() method and MWDMA0/1 support
Add the speedproc() method for setting transfer modes, modify config_for_dma()
to call it and use ide_max_dma_mode() to select the best DMA mode.
Add support for the multiword DMA modes 0 and 1, using the upper half of the
'drive_data' field to store the DMA timings to program into the drive control
register when DMA is turned on for real.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:44 +02:00
Bartlomiej Zolnierkiewicz
3c3f5d2c9f cs5530/sc1200: add ->speedproc support
* add {cs5530,sc1200}_tunepio() for programming PIO timings

* add {cs5530,sc1200}_tune_chipset() (->speedproc method) for setting
  transfer mode and convert {cs5530,sc1200}_config_dma() to use it

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:44 +02:00
Bartlomiej Zolnierkiewicz
a01ba4011a cs5530/sc1200: DMA support cleanup
sc1200.c:

* remove open-coded variant of ide_dma_host_off() (== ->dma_host_off),
  it is not needed because ->dma_off_quietly calls ->dma_host_off

* use ->dma_host_on (== ide_dma_host_on() for this driver) instead of
  open-coded variant, call it from the users of sc1200_config_dma2()

  [ there is no need to call ->dma_host_on in sc1200_config_dma() because
    core code takes care of calling ->ide_dma_on on successful execution
    of ->ide_dma_check ]

* add comment about ->tuneproc interface abuse

cs5530.c/sc1200.c:

* core code takes care of calling ->dma_off_quietly before calling
  ->ide_dma_check so there is no need to call it in ->ide_dma_check methods

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:44 +02:00
Bartlomiej Zolnierkiewicz
bd203b57c7 ide: use ide_tune_dma() part #2
Use ide_tune_dma() in ide-cris/it821x/pdc202xx_old/serverworks drivers.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
5fd216bbb2 cs5530/sc1200: add ->udma_filter methods
CS5530/SC1200 specifies that two drives on the same cable cannot mix
UDMA/MDMA.  Add {cs5530,sc1200}_udma_filter() to handle this.  This also
makes it possible to remove open-coded best DMA mode selection and use
standard ide_use_dma()/ide_max_dma_mode() helpers.  While at it bump
version numbers.

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
793a97228d ide: always disable DMA before tuning it
ide_start_power_step() and set_using_dma() were missing ->dma_off_quietly
call (comment in probe_hwif() states that DMA should be always cleared before
tuning is attempted).  Fix it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
7f86723a60 pdc202xx_new: use ide_tune_dma()
* remove code enabling IORDY and prefetch from config_chipset_for_dma(),
  as the comment states it has no real effect because these settings are
  overriden when the PIO mode is set (and for this driver ->autotune == 1
  so PIO mode is always programmed)

* use ide_tune_dma() in pdcnew_config_drive_xfer_rate() and remove no longer
  needed config_chipset_for_dma()

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
38ff8a74e8 alim15x3: use ide_tune_dma()
Use ide_tune_dma() in ali15x3_config_drive_for_dma() and remove all the open
coded DMA tuning code and also config_chipset_for_dma().  Set ->atapi_dma flag
correctly in init_hwif_common_ali15x3() so ide_tune_dma() can take care of
checking if ATAPI DMA is allowed and remove open coded ATAPI DMA check from
ali15x3_config_drive_for_dma().

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
6b8cf7724b sis5513: PIO mode setup fixes
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to program PIO5 by config_art_rwp_pio() could result in incorrect PIO
  timings being programmed and possibly the data corruption (for < ATA100
  family chipsets PIO0 timings were used, for ATA100 and ATA100a - the random
  content of test1 variable was used, for ATA133 - MWDMA0 timings were used)

* BUG() in sis5513_tune_chipset() if somebody tries to force unsupported PIO5,
  also cleanup this function a bit while at it

* add comment about PIO0 timings for < ATA100 family chipsets

* remove open-coded best PIO mode selection from config_art_rwp_pio(),
  it contained numerous bugs:

  - it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
    before using them

  - it tried to found out maximum PIO mode basing on minimum IORDY cycle time
    (moreover wrong cycle times were used for PIO1/5)

  - it was overriding PIO blacklist and conservative PIO "downgrade" done
    by ide_get_best_pio_mode()

* use sis5513_tune_drive() instead of config_art_rwp_pio()
  in sis5513_config_xfer_rate() so the correct PIO mode is also set
  on drive even if the device is not IORDY/DMA capable

* config_art_rwp_pio() was always setting the best possible mode and not
  the wanted one - fix it and move ide_get_best_pio_mode() call to
  config_chipset_for_pio()

* don't use ide_find_best_mode() in config_chipset_for_pio(), it was being
  overriden by config_art_rwp_pio() for the host timings anyway + we need to
  set the same PIO mode on the device and the host

* pass correct "pio" argument (255 instead of 5) to sis5513_tune_drive() call
  in sis5513_config_xfer_rate() so the best PIO mode is set on the drive
  and not PIO4

* rename sis5513_tune_drive() to sis5513_tuneproc()
  and config_chipset_for_pio() to sis5513_tune_driver()

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:42 +02:00
Bartlomiej Zolnierkiewicz
9445de76c1 serverworks: PIO mode setup fixes
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to program PIO5 by svwks_tune_chipset() could result in incorrect PIO
  timings being programmed and possibly the data corruption (it seems that
  the minimum possible values were used but I lack the datasheets to be sure)

* select best PIO mode in svwks_tune_drive() and not in svwks_tune_chipset()
  when doing PIO autotuning (pio == 255)

* don't try to tune PIO in config_chipset_for_dma() as ide_dma_enable() could
  return 1 if DMA was previously enabled (svwks_config_drive_xfer_rate()
  takes care of PIO tuning if no suitable DMA mode is found)

* remove config_chipset_for_pio() and use svwks_tune_drive() instead,
  config_chipset_for_pio() contained numerous bugs when selecting PIO mode
  (luckily it was only used for devices limited to PIO by capabilities/BIOS):

  - it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
    before using them

  - it tried to found out maximum PIO mode basing on minimum IORDY cycle time
    (moreover wrong cycle times were used for PIO0/1/5)

  - it was overriding PIO blacklist and conservative PIO "downgrade" done
    by ide_get_best_pio_mode()

  - if the max drive PIO was PIO5 then XFER_PIO_0/XFER_PIO_SLOW was selected
    (XFER_PIO_SLOW is not supported by svwks_tune_chipset() so the result
     was the same as if using XFER_PIO_5 => wrong PIO timings were set)

  - it was overriding drive->current_speed

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:42 +02:00
Bartlomiej Zolnierkiewicz
4fce3164b8 pdc202xx_old: rewrite mode programming code (v2)
This patch is based on the documentation (I would like to thank Promise
for it) and also partially on the older vendor driver.

Rewrite mode programming code:

* disable 66MHz clock in pdc202xx_tune_chipset() so it is correctly disabled
  even if both devices on the channel are not DMA capable and after reset

* enable/disable IORDY and PREFETCH bits in pdc202xx_tune_chipset()
  as they need to be setup correctly also for PIO only devices, plus IORDY
  wasn't disabled for non-IORDY devices and PREFETCH wasn't disabled for
  ATAPI devices

* remove dead code for setting SYNC_ERDDY_EN bits from config_chipset_for_dma()
  (driver sets ->autotune to 1 so PIO modes are always programmed => lower
   nibble of register A never equals 4 => "chipset_is_set" is always true)

* enable PIO mode programming for all ATAPI devices
  (it was limited to ->media == ide_cdrom devices)

* remove extra reads of registers A/B/C, don't read register D et all

* do clearing / programming of registers A/B/C in one go
  (gets rid of extra PCI config space read/write cycle)

* set initial values of drive_conf/AP/BP/CP variables to zero
  (paranoia for the case when PCI reads fail)

* remove XFER_UDMA6 to XFER_UDMA5 remapping case - it can't happen
  (ide_rate_filter() takes care of it)

* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)

* fix bitmasks for clearing bits of register B:

  - when programming DMA mode bit 0x10 of register B was cleared which
    resulted in overclocked PIO timing setting (iff PIO0 was used)

  - when programming PIO mode bits 0x18 weren't cleared so suboptimal
    timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
    and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)

* add FIXME comment about missing locking for 66MHz clock register

Also while at it:

* remove unused defines

* do a few cosmetic / CodingStyle fixes

* bump driver version

v2:
* in pdc202xx_tune_chipset() the old content of drive configuration
  registers is used only by the debugging code so cover "drive_conf"
  PCI registers read by #if PDC202XX_DEBUG_DRIVE_INFO
  (Noticed by Sergei Shtylyov)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:41 +02:00
Russell King
10bdaaa0fa [ARM] ecard: add ecardm_iomap() / ecardm_iounmap()
Add devres ecardm_iomap() and ecardm_iounmap() for Acorn expansion
cards.  Convert all expansion card drivers to use them.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-11 17:19:02 +01:00
Russell King
c7b87f3d50 [ARM] ecard: add helper function for setting ecard irq ops
Rather than having every driver fiddle about setting its private
IRQ operations and data, provide a helper function to contain
this functionality in one place.

Arrange to remove the driver-private IRQ operations and data when
the device is removed from the driver, and remove the driver
private code to do this.

This fixes potential problems caused by drivers forgetting to
remove these hooks.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-11 17:18:55 +01:00
Martin Schwidefsky
e25df1205f [S390] Kconfig: menus with depends on HAS_IOMEM.
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2007-05-10 15:46:07 +02:00
Linus Torvalds
3cb7396b7b Merge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: fix PIO setup on resume for ATAPI devices
  ide: legacy PCI bus order probing fixes
  ide: add ide_proc_register_port()
  ide: add "initializing" argument to ide_register_hw()
  ide: cable detection fixes (take 2)
  ide: move IDE settings handling to ide-proc.c
  ide: split off ioctl handling from IDE settings (v2)
  ide: make /proc/ide/ optional
  ide: add ide_tune_dma() helper
  ide: rework the code for selecting the best DMA transfer mode (v3)
  ide: fix UDMA/MWDMA/SWDMA masks (v3)
2007-05-09 15:41:31 -07:00
Bartlomiej Zolnierkiewicz
317a46a200 ide: fix PIO setup on resume for ATAPI devices
PIO should be restored also for ATAPI devices during resume, fix it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:11 +02:00
Bartlomiej Zolnierkiewicz
6d208b39c4 ide: legacy PCI bus order probing fixes
IDE PCI host drivers should register themselves with IDE core only when
IDE driver is built-in, otherwise (IDE driver is modular and thus IDE PCI
host drivers are also modular) the code has no effect and just complicates
the probing.

Fix it by adding new config option CONFIG_IDEPCI_PCIBUS (defined only when
needed and invisible to the user) and covering by #ifdef/#endif the code
in question.  It turned out that "ide=reverse" was silently accepted but did
nothing in case when IDE driver was modular, this is fixed now.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:11 +02:00
Bartlomiej Zolnierkiewicz
5cbf79cdb3 ide: add ide_proc_register_port()
* create_proc_ide_interfaces() tries to add /proc entries for every probed
  and initialized IDE port, replace it by ide_proc_register_port() which does
  it only for the given port (also rename destroy_proc_ide_interface() to
  ide_proc_unregister_port() for consistency)
  
* convert {create,destroy}_proc_ide_interface[s]() users to use new functions

* pmac driver depended on proc_ide_create() to add /proc port entries, fix it
  
* au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic
  driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them

* there is now no need to add /proc entries for IDE ports in proc_ide_create()
  so don't do it

* proc_ide_create() needs now to be called before drivers are probed - fix it,
  while at it make proc_ide_create() create /proc "ide" directory

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:11 +02:00
Bartlomiej Zolnierkiewicz
869c56ee9d ide: add "initializing" argument to ide_register_hw()
Add "initializing" argument to ide_register_hw() and use it instead of ide.c
wide variable of the same name.  Update all users of ide_register_hw()
accordingly.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:10 +02:00
Bartlomiej Zolnierkiewicz
7f8f48af08 ide: cable detection fixes (take 2)
Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...

* print user-friendly warning about limiting the maximum transfer speed
  to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
  also while at it cleanup eighty_ninty_three() a bit

* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
  - bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
    were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
    (please see FIXME comment in eighty_ninty_three() for more details)
  - CONFIG_IDEDMA_IVB=y/n cases were interchanged
  - check for SATA devices was missing

* remove private cable warnings from pdc_202xx{old,new} drivers now that core
  code provides this functionality (plus, in pdc202xx_new case the test could
  give false warnings for ATAPI devices because pdc202xx_new driver doesn't
  even support ATAPI DMA)

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:10 +02:00
Bartlomiej Zolnierkiewicz
7662d046df ide: move IDE settings handling to ide-proc.c
* move
	__ide_add_setting()
	ide_add_setting()
	__ide_remove_setting()
	auto_remove_settings()
	ide_find_setting_by_name()
	ide_read_setting()
	ide_write_setting()
	set_xfer_rate()
	ide_add_generic_settings()
	ide_register_subdriver()
	ide_unregister_subdriver()

  from ide.c to ide-proc.c

* set_{io_32bit,pio_mode,using_dma}() cannot be marked static now, fix it

* rename ide_[un]register_subdriver() to ide_proc_[un]register_driver(),
  update device drivers to use new names

* add CONFIG_IDE_PROC_FS=n versions of ide_proc_[un]register_driver()
  and ide_add_generic_settings()

* make ide_find_setting_by_name(), ide_{read,write}_setting()
  and ide_{add,remove}_proc_entries() static

* cover IDE settings code in device drivers with CONFIG_IDE_PROC_FS #ifdef,
  also while at it cover with CONFIG_IDE_PROC_FS #ifdef ide_driver_t.proc

* remove bogus comment from ide.h

* cover with CONFIG_IDE_PROC_FS #ifdef .proc and .settings in ide_drive_t

Besides saner code this patch results in the IDE core smaller by ~2 kB
(on x86-32) and IDE disk driver by ~1 kB (ditto) when CONFIG_IDE_PROC_FS=n.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:10 +02:00
Bartlomiej Zolnierkiewicz
1497943ee6 ide: split off ioctl handling from IDE settings (v2)
* do write permission and min/max checks in ide_procset_t functions

* ide-disk.c: drive->id is always available so cleanup "multcount" setting
  accordingly

* ide-disk.c: "address" setting was incorrectly defined as type TYPE_INTA,
  fix it by using type TYPE_BYTE and updating ide_drive_t->adressing field,
  the bug didn't trigger because this IDE setting uses custom ->set function

* ide.c: add set_ksettings() for handling HDIO_SET_KEEPSETTINGS ioctl

* ide.c: add set_unmaskirq() for handling HDIO_SET_UNMASKINTR ioctl

* handle ioctls directly in generic_ide_ioclt() and idedisk_ioctl()
  instead of using IDE settings to deal with them

* remove no longer needed ide_find_setting_by_ioctl() and {read,write}_ioctl
  fields from ide_settings_t, also remove now unused TYPE_INTA handling

v2:
* add missing EXPORT_SYMBOL_GPL(ide_setting_sem) needed now for ide-disk

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:10 +02:00
Bartlomiej Zolnierkiewicz
ecfd80e4a5 ide: make /proc/ide/ optional
All important information/features should be already available through
sysfs and ioctl interfaces.

Add CONFIG_IDE_PROC_FS (CONFIG_SCSI_PROC_FS rip-off) config option,
disabling it makes IDE driver ~5 kB smaller (on x86-32).

While at it add CONFIG_PROC_FS=n versions of proc_ide_{create,destroy}()
and remove no longer needed #ifdefs.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:09 +02:00
Bartlomiej Zolnierkiewicz
29e744d088 ide: add ide_tune_dma() helper
After reworking the code responsible for selecting the best DMA
transfer mode it is now possible to add generic ide_tune_dma() helper.

Convert some IDE PCI host drivers to use it (the ones left need more work).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:09 +02:00
Bartlomiej Zolnierkiewicz
2d5eaa6dd7 ide: rework the code for selecting the best DMA transfer mode (v3)
Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.

* add ide_hwif_t.udma_filter hook for filtering UDMA mask
  (use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
  (loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
  of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()

v2:
* rename ->filter_udma_mask to ->udma_filter
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
  originated transfer mode change requests when 100MHz clock is used)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:08 +02:00
Bartlomiej Zolnierkiewicz
1813720723 ide: fix UDMA/MWDMA/SWDMA masks (v3)
* use 0x00 instead of 0x80 to disable ->{ultra,mwdma,swdma}_mask
* add udma_mask field to ide_pci_device_t and use it to initialize
  ->ultra_mask in aec62xx, cmd64x, pdc202xx_{new,old} and piix drivers
* fix UDMA masks to match with chipset specific *_ratemask()
  (alim15x3, hpt366, serverworks and siimage drivers need UDMA mask
   filtering method - done in the next patch)

v2:
* piix: fix cable detection for 82801AA_1 and 82372FB_1
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* cmd64x: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* aec62xx: fix newly introduced bug - check DMA status not command register
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* piix: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:07 +02:00
Michael Opdenacker
59c51591a0 Fix occurrences of "the the "
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2007-05-09 08:57:56 +02:00
Paul Mackerras
02bbc0f09c Merge branch 'linux-2.6' 2007-05-08 13:37:51 +10:00
Stephen Rothwell
55b61fec22 [POWERPC] Rename device_is_compatible to of_device_is_compatible
for consistency with other Open Firmware interfaces (and Sparc).

This is just a straight replacement.

This leaves the compatibility define in place.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-07 20:31:14 +10:00
Fabrice Aeschbacher
aa12b2842a ide-cs: recognize 2GB CompactFlash from Transcend
Without the following patch, the kernel does not automatically detect
2GB CompactFlash cards from Transcend.

Signed-off-by: Fabrice Aeschbacher <fabrice.aeschbacher@siemens.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:51 +02:00
Sergei Shtylyov
fdb0d72be4 hpt366: don't check enablebits for HPT36x
HPT36x chip don't seem to have the channel enable bits, so prevent the IDE core
from checking them...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Michal Kepien <michal.kepien@poczta.onet.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:51 +02:00
Bartlomiej Zolnierkiewicz
55e4dee329 ide-cris: fix ->speedproc and wrong ->swdma_mask
* fix ->speedproc to set the drive speed

* this driver doesn't support SWDMA so use the correct ->swdma_mask

* BUG() if an unsupported mode is passed to ->speedproc

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:51 +02:00