During page sync, if a pagetable contains a self referencing pte (that
points to the pagetable), the corresponding spte may be marked as
writable even though all mappings are supposed to be write protected.
Fix by clearing page unsync before syncing individual sptes.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
PAL_VPS_RESUME_HANDLER should use r26 to hold vac fields according to SDM.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use CFLAGS_vcpu.o, not EXTRA_CFLAGS, to provide fixed register information
to the compiler.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If an interrupt cannot be injected for some reason (say, page fault
when fetching the IDT descriptor), the interrupt is marked for
reinjection. However, if an NMI is queued at this time, the NMI
will be injected instead and the NMI will be lost.
Fix by deferring the NMI injection until the interrupt has been
injected successfully.
Analyzed by Jan Kiszka.
Signed-off-by: Avi Kivity <avi@redhat.com>
We can get an exit for instructions starting with 0xae, even if the guest is
in userspace. Lets make sure, that the signal processor handler is only called
in guest supervisor mode. Otherwise, send a program check.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Impact: fix MSIx not enough irq numbers available regression
The manual revert of the sparse_irq patches missed to bring the number
of possible irqs back to the .27 status. This resulted in a regression
when two multichannel network cards were placed in a system with only
one IO_APIC - causing the networking driver to not have the right
IRQ and the device not coming up.
Remove the dynamic allocation logic leftovers and simply return
NR_IRQS in probe_nr_irqs() for now.
Fixes: http://lkml.org/lkml/2008/11/19/354
Reported-by: Jesper Dangaard Brouer <hawk@diku.dk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jesper Dangaard Brouer <hawk@diku.dk>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The G3IPL expects the value at RAM address 0xa020b020 to be
exactly 1 to setup the bluetooth GPIOs properly. The actual
code got a value from gpio_get_value() which was not 1, but
a "not equal to 0" integer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
In the resume bootstrap, the early disable address is wrong.
Fix it to RAM address 0xa020b000 instead of 0xa0200000, and
make it consistent with RESUME_ENABLE_ADDR in mioa701.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5330/1: mach-pxa: Fixup reset for systems using reboot=cold or other strings
[ARM] pxa: fix incorrect PCMCIA PSKTSEL pin configuration for spitz
[ARM] pxa: fix I2C controller device being registered twice on Akita
pxafb: only initialize the smart panel thread when dealing with a smartpanel
pxafb: introduce LCD_TYPE_MASK and use it.
Currently, we can end up in an infinite loop if we get a signal
while the kernel has faulted in spufs_ps_fault. Eg:
alarm(1);
write(fd, some_spu_psmap_register_address, 4);
- the write's copy_from_user will fault on the ps mapping, and
signal_pending will be non-zero. Because returning from the fault
handler will never clear TIF_SIGPENDING, so we'll just keep faulting,
resulting in an unkillable process using 100% of CPU.
This change returns VM_FAULT_SIGBUS if there's a fatal signal pending,
letting us escape the loop.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
fix xen_get_eflags. It doesn't take any argument.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pv_cpu_ops.getreg(_IA64_REG_IP) returned constant.
But the returned ip valued should be the one in the caller, not of the callee.
This patch fixes that.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/kernel/pci-dma.c only needs to include iommu once.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Using printk from MCA/INIT context is unsafe since it can cause deadlock.
The ia64_mca_modify_original_stack is called from both of mca handler and
init handler, so it should use mprintk instead of printk.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Itanium processors can handle some misaligned data accesses. They
also provide a mode where all such accesses are forced to trap. The
kernel was schizophrenic about use of this mode:
* Base kernel code ran in permissive mode where the only traps
generated were from those cases that the h/w could not handle.
* Interrupt, syscall and trap code ran in strict mode where all
unaligned accesses caused traps to the 0x5a00 unaligned reference
vector.
Use strict alignment checking throughout the kernel, but make
sure that we continue to let user mode use more relaxed mode
as the default.
Signed-off-by: Tony Luck <tony.luck@intel.com>
When we migrate an interrupt from one CPU to another, we set the
move_in_progress flag and clean up the vectors later once they're not
being used. If you're unlucky and call destroy_irq() before the vectors
become un-used, the move_in_progress flag is never cleared, which causes
the interrupt to become unusable.
This was discovered by Jesse Brandeburg for whom it manifested as an
MSI-X device refusing to use MSI-X mode when the driver was unloaded
and reloaded repeatedly.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: csrc-r4k: Fix declaration depending on the wrong CONFIG_ symbol.
MIPS: csrc-r4k: Fix spelling mistake.
MIPS: RB532: Provide functions for gpio configuration
MIPS: IP22: Make indy_sc_ops variable static
MIPS: RB532: GPIO register offsets are relative to GPIOBASE
MIPS: Malta: Fix include paths in malta-amon.c
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: uaccess_64: fix return value in __copy_from_user()
x86: quirk for reboot stalls on a Dell Optiplex 330
Commit 81e192d6ce ("parisc: convert to
generic compat_sys_ptrace") introduced a bug which segfaults the parisc
64bit kernel when stracing 32bit applications:
Kernel Fault: Code=15 regs=00000000bafa42b0 (Addr=00000001baf5ab57)
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001101111111100001011 Tainted: G W
r00-03 000000ff0806ff0b 000000004068edc0 00000000401203f8 00000000fb3e2508
r04-07 0000000040686dc0 00000000baf5a800 fffffffffffffffc fffffffffb3e2508
r08-11 00000000baf5a800 000000000004b068 00000000000402b0 0000000000040d68
r12-15 0000000000042a9c 0000000000040a9c 0000000000040d60 0000000000042e9c
r16-19 000000000004b060 000000000004b058 0000000000042d9c ffffffffffffffff
r20-23 000000000800000b 0000000000000000 000000000800000b fffffffffb3e2508
r24-27 00000000fffffffc 0000000000000003 00000000fffffffc 0000000040686dc0
r28-31 00000001baf5a7ff 00000000bafa4280 00000000bafa42b0 00000000000001d7
sr00-03 0000000000fca000 0000000000000000 0000000000000000 0000000000fca000
sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
IASQ: 0000000000000000 0000000000000000 IAOQ: 0000000040120400 0000000040120404
IIR: 4b9a06b0 ISR: 0000000000000000 IOR: 00000001baf5ab57
CPU: 0 CR30: 00000000bafa4000 CR31: 00000000d22344e0
ORIG_R28: 00000000fb3e2248
IAOQ[0]: compat_arch_ptrace+0xb8/0x160
IAOQ[1]: compat_arch_ptrace+0xbc/0x160
RP(r2): compat_arch_ptrace+0xb0/0x160
Backtrace:
[<00000000401612ac>] compat_sys_ptrace+0x15c/0x180
[<0000000040104ef8>] syscall_exit+0x0/0x14
The problem is that compat_arch_ptrace() enters with an addr value of
type compat_ulong_t and calls translate_usr_offset() to translate the
address offset into a struct pt_regs offset like this:
addr = translate_usr_offset(addr)
this means that any return value of translate_usr_offset() is stored
back as compat_ulong_t type into the addr variable.
But since translate_usr_offset() returns -1 for invalid offsets, addr
can now get the value 0xffffffff which then fails the next return-value
sanity check and thus the kernel tries to access invalid memory:
if (addr < 0)
break;
Fix this bug by modifying translate_usr_offset() to take and return
values of type compat_ulong_t, and by returning the value
"sizeof(struct pt_regs)" as an error indicator.
Additionally change the sanity check to check for return values
for >= sizeof(struct pt_regs).
This patch survived my compile and run-tests.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As gpiolib doesn't support pin multiplexing, it provides no way to
access the GPIOFUNC register. Also there is no support for setting
interrupt status and level. These functions provide access to them and
are needed by the CompactFlash driver.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The indy_sc_ops variable in arch/mips/mm/sc-ip22.c is needlessly defined
global, and this patch makes it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
This patch fixes the wrong use of GPIO register offsets
in devices.c. To avoid further problems, use gpio_get_value
to return the NAND status instead of our own expanded code.
Also define the zero offset of the alternate function register to allow
consistent access.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On linux-queue, malta doesn't build after the include file relocation.
This should fix it.
There some occurrences of 'asm-mips' in the comments of quite a few
files, but this is the only place I found it in any code.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Annotate xsave_cntxt_init() as "can be called outside of __init".
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix incorrect __init annotation
This patch removes the following section mismatch warning. A patch set
was send previously (http://lkml.org/lkml/2008/11/10/407). But
introduce some other problem, reported by Rufus
(http://lkml.org/lkml/2008/11/11/46). Then Ingo Molnar suggest that,
it's best to remove __init from xsave_cntxt_init(void). Which is the
second patch in this series. Now, this one removes the following
warning.
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x2237): Section
mismatch in reference from the function cpu_init() to the function
.init.text:init_thread_xstate()
The function __cpuinit cpu_init() references
a function __init init_thread_xstate().
If init_thread_xstate is only used by cpu_init then
annotate init_thread_xstate with a matching annotation.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86/numa' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: make NUMA on 32-bit depend on EXPERIMENTAL again
x86, hibernate: fix breakage on x86_32 with CONFIG_NUMA set
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: more general identifier for Phoenix BIOS
AMD IOMMU: check for next_bit also in unmapped area
AMD IOMMU: fix fullflush comparison length
AMD IOMMU: enable device isolation per default
AMD IOMMU: add parameter to disable device isolation
x86, PEBS/DS: fix code flow in ds_request()
x86: add rdtsc barrier to TSC sync check
xen: fix scrub_page()
x86: fix es7000 compiling
x86, bts: fix unlock problem in ds.c
x86, voyager: fix smp generic helper voyager breakage
x86: move iomap.h to the new include location
This adds the sparc syscall hookups.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a new accept4() system call. The addition of this system call
matches analogous changes in 2.6.27 (dup3(), evenfd2(), signalfd4(),
inotify_init1(), epoll_create1(), pipe2()) which added new system calls
that differed from analogous traditional system calls in adding a flags
argument that can be used to access additional functionality.
The accept4() system call is exactly the same as accept(), except that
it adds a flags bit-mask argument. Two flags are initially implemented.
(Most of the new system calls in 2.6.27 also had both of these flags.)
SOCK_CLOEXEC causes the close-on-exec (FD_CLOEXEC) flag to be enabled
for the new file descriptor returned by accept4(). This is a useful
security feature to avoid leaking information in a multithreaded
program where one thread is doing an accept() at the same time as
another thread is doing a fork() plus exec(). More details here:
http://udrepper.livejournal.com/20407.html "Secure File Descriptor Handling",
Ulrich Drepper).
The other flag is SOCK_NONBLOCK, which causes the O_NONBLOCK flag
to be enabled on the new open file description created by accept4().
(This flag is merely a convenience, saving the use of additional calls
fcntl(F_GETFL) and fcntl (F_SETFL) to achieve the same result.
Here's a test program. Works on x86-32. Should work on x86-64, but
I (mtk) don't have a system to hand to test with.
It tests accept4() with each of the four possible combinations of
SOCK_CLOEXEC and SOCK_NONBLOCK set/clear in 'flags', and verifies
that the appropriate flags are set on the file descriptor/open file
description returned by accept4().
I tested Ulrich's patch in this thread by applying against 2.6.28-rc2,
and it passes according to my test program.
/* test_accept4.c
Copyright (C) 2008, Linux Foundation, written by Michael Kerrisk
<mtk.manpages@gmail.com>
Licensed under the GNU GPLv2 or later.
*/
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/socket.h>
#include <netinet/in.h>
#include <stdlib.h>
#include <fcntl.h>
#include <stdio.h>
#include <string.h>
#define PORT_NUM 33333
#define die(msg) do { perror(msg); exit(EXIT_FAILURE); } while (0)
/**********************************************************************/
/* The following is what we need until glibc gets a wrapper for
accept4() */
/* Flags for socket(), socketpair(), accept4() */
#ifndef SOCK_CLOEXEC
#define SOCK_CLOEXEC O_CLOEXEC
#endif
#ifndef SOCK_NONBLOCK
#define SOCK_NONBLOCK O_NONBLOCK
#endif
#ifdef __x86_64__
#define SYS_accept4 288
#elif __i386__
#define USE_SOCKETCALL 1
#define SYS_ACCEPT4 18
#else
#error "Sorry -- don't know the syscall # on this architecture"
#endif
static int
accept4(int fd, struct sockaddr *sockaddr, socklen_t *addrlen, int flags)
{
printf("Calling accept4(): flags = %x", flags);
if (flags != 0) {
printf(" (");
if (flags & SOCK_CLOEXEC)
printf("SOCK_CLOEXEC");
if ((flags & SOCK_CLOEXEC) && (flags & SOCK_NONBLOCK))
printf(" ");
if (flags & SOCK_NONBLOCK)
printf("SOCK_NONBLOCK");
printf(")");
}
printf("\n");
#if USE_SOCKETCALL
long args[6];
args[0] = fd;
args[1] = (long) sockaddr;
args[2] = (long) addrlen;
args[3] = flags;
return syscall(SYS_socketcall, SYS_ACCEPT4, args);
#else
return syscall(SYS_accept4, fd, sockaddr, addrlen, flags);
#endif
}
/**********************************************************************/
static int
do_test(int lfd, struct sockaddr_in *conn_addr,
int closeonexec_flag, int nonblock_flag)
{
int connfd, acceptfd;
int fdf, flf, fdf_pass, flf_pass;
struct sockaddr_in claddr;
socklen_t addrlen;
printf("=======================================\n");
connfd = socket(AF_INET, SOCK_STREAM, 0);
if (connfd == -1)
die("socket");
if (connect(connfd, (struct sockaddr *) conn_addr,
sizeof(struct sockaddr_in)) == -1)
die("connect");
addrlen = sizeof(struct sockaddr_in);
acceptfd = accept4(lfd, (struct sockaddr *) &claddr, &addrlen,
closeonexec_flag | nonblock_flag);
if (acceptfd == -1) {
perror("accept4()");
close(connfd);
return 0;
}
fdf = fcntl(acceptfd, F_GETFD);
if (fdf == -1)
die("fcntl:F_GETFD");
fdf_pass = ((fdf & FD_CLOEXEC) != 0) ==
((closeonexec_flag & SOCK_CLOEXEC) != 0);
printf("Close-on-exec flag is %sset (%s); ",
(fdf & FD_CLOEXEC) ? "" : "not ",
fdf_pass ? "OK" : "failed");
flf = fcntl(acceptfd, F_GETFL);
if (flf == -1)
die("fcntl:F_GETFD");
flf_pass = ((flf & O_NONBLOCK) != 0) ==
((nonblock_flag & SOCK_NONBLOCK) !=0);
printf("nonblock flag is %sset (%s)\n",
(flf & O_NONBLOCK) ? "" : "not ",
flf_pass ? "OK" : "failed");
close(acceptfd);
close(connfd);
printf("Test result: %s\n", (fdf_pass && flf_pass) ? "PASS" : "FAIL");
return fdf_pass && flf_pass;
}
static int
create_listening_socket(int port_num)
{
struct sockaddr_in svaddr;
int lfd;
int optval;
memset(&svaddr, 0, sizeof(struct sockaddr_in));
svaddr.sin_family = AF_INET;
svaddr.sin_addr.s_addr = htonl(INADDR_ANY);
svaddr.sin_port = htons(port_num);
lfd = socket(AF_INET, SOCK_STREAM, 0);
if (lfd == -1)
die("socket");
optval = 1;
if (setsockopt(lfd, SOL_SOCKET, SO_REUSEADDR, &optval,
sizeof(optval)) == -1)
die("setsockopt");
if (bind(lfd, (struct sockaddr *) &svaddr,
sizeof(struct sockaddr_in)) == -1)
die("bind");
if (listen(lfd, 5) == -1)
die("listen");
return lfd;
}
int
main(int argc, char *argv[])
{
struct sockaddr_in conn_addr;
int lfd;
int port_num;
int passed;
passed = 1;
port_num = (argc > 1) ? atoi(argv[1]) : PORT_NUM;
memset(&conn_addr, 0, sizeof(struct sockaddr_in));
conn_addr.sin_family = AF_INET;
conn_addr.sin_addr.s_addr = htonl(INADDR_LOOPBACK);
conn_addr.sin_port = htons(port_num);
lfd = create_listening_socket(port_num);
if (!do_test(lfd, &conn_addr, 0, 0))
passed = 0;
if (!do_test(lfd, &conn_addr, SOCK_CLOEXEC, 0))
passed = 0;
if (!do_test(lfd, &conn_addr, 0, SOCK_NONBLOCK))
passed = 0;
if (!do_test(lfd, &conn_addr, SOCK_CLOEXEC, SOCK_NONBLOCK))
passed = 0;
close(lfd);
exit(passed ? EXIT_SUCCESS : EXIT_FAILURE);
}
[mtk.manpages@gmail.com: rewrote changelog, updated test program]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Tested-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ethernet0 (called FSL UEC0 in U-Boot) should be enet1 (UCC3/eth1), and
ethernet1 should be enet0 (UCC2/eth0), to be consistent with U-Boot so
that the interfaces do not swap addresses when control passes from
U-Boot to the kernel.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Marvell PHY driver is currently being used for the 88E1111 on the
SBC610. This driver is causing the link to run in 10/Half mode, the generic
PHY driver is correctly configuring the PHY as 1000/Full.
Edit default config to use generic PHY driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It's 1MB, not 512KB. Newer U-Boots will fix this entry, but that's no
reason to have the wrong value in the dts.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPIC has 4 ipis, so it can use the new smp_request_message_ipi to
reduce pathlength when receiving an ipi.
This has the side effect of using the common ipi names, and also
continuing to try request the remaining messages when one fails.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With the new generic smp call function helpers, I noticed the code in
smp_message_recv was a single function call in many cases. While
getting the message number from the ipi data is easy, we can reduce
the path length by a function and data-dependent switch by registering
seperate IPI actions for these simple calls.
Originally I left the ipi action array exposed, but then I realized the
registration code should be common too.
The three users each had their own name array, so I made a fourth
to convert all users to use a common one.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Linux will report the number of page-ins so that the hypervisor can
better determine partition memory pressure. The hardware page size
and the OS page size can be different. In the case where the hardware
page size is 4k and the OS is running with 64k pages the code in
commit 409001948d ("powerpc: Update
page-in counter for CMM") would under-report the number of pages.
This corrects the reporting to the hypervisor by incrementing the
page_in count by 1 << PAGE_FACTOR each time.
Reported-by: Andrew Theurer <habanero@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements an optimised mutex fastpath for powerpc, making use of
acquire and release barrier semantics. This takes the mutex
lock+unlock benchmark from 203 to 173 cycles on a G5.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After commit 598056d5af ("[POWERPC] Fix
rmb to order cacheable vs. noncacheable"), rmb() becomes a sync
instruction, which is needed to order cacheable vs noncacheable loads.
However smp_rmb() is #defined to rmb(), and smp_rmb() can be an
lwsync.
This restores smp_rmb() performance by using lwsync there and updates
the comments.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change 2d1b202762 ("powerpc: Fixup
lwsync at runtime") removed __SUBARCH_HAS_LWSYNC, causing smp_wmb to
revert back to eieio for all CPUs. This restores the behaviour
intorduced in 74f0609526 ("powerpc:
Optimise smp_wmb on 64-bit processors").
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In exactly the same way that we updated memcpy() with new feature
sections in commit 25d6e2d7c5 ("powerpc:
Update 64bit memcpy() using CPU_FTR_UNALIGNED_LD_STD"), we do the same
thing here for __copy_tofrom_user(). Once again this is purely a
performance tweak for Cell and Power6 - this has no effect on all the
other 64bit powerpc chips.
We can make these same changes to __copy_tofrom_user() because the
basic copy algorithm is the same as in memcpy() - this version just
has all the exception handling logic needed when copying to or from
userspace as well as a special case for copying whole 4K pages that
are page aligned.
CPU_FTR_UNALIGNED_LD_STD CPU was added in commit
4ec577a289 ("powerpc: Add new CPU
feature: CPU_FTR_UNALIGNED_LD_STD").
We also make the same simple one line change from cmpldi r1,... to
cmpldi cr1,... for consistency.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I can't tell why this WARN_ON exists, and there's no comment
explaining it. Whether the pmd is present or not, pte_alloc_kernel()
seems to handle both cases.
Booting a 440 kernel with 64K PAGE_SIZE triggers the warning, but boot
successfully completes and I see no problems beyond that.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have several instances of inline assembly code that use the addic
or addic. instructions, but don't include XER in the list of clobbers.
The addic and addic. instructions affect the carry bit, which is in
the XER register.
This adds "xer" to the list of clobbers for those inline asm
statements that use addic or addic. and didn't already have it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Introduce ps3_gpu_mutex to synchronizes GPU-related operations, like:
- invoking the L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT command using the
lv1_gpu_context_attribute() hypervisor call,
- handling the PS3AV_CID_AVB_PARAM packet in the PS3 A/V Settings driver.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
__copy_from_user() will return invalid value 16 when it fails to
access user space and the size is 10.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dell Optiplex 330 appears to hang on reboot. This is resolved by adding
a quirk to set bios reboot.
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Steve Conklin <steve.conklin@canonical.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: widen the reach of the low-memory-protect DMI quirk
Phoenix BIOSes variously identify their vendor as "Phoenix Technologies,
LTD" or "Phoenix Technologies LTD" (without the comma.)
This patch makes the identification string in the bad_bios_dmi_table
more general (following a suggestion by Ingo Molnar), so that both
versions are handled.
Again, the patched file compiles cleanly and the patch has been tested
successfully on my machine.
Signed-off-by: Philipp Kohlbecher <xt28@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: makes device isolation the default for AMD IOMMU
Some device drivers showed double-free bugs of DMA memory while testing
them with AMD IOMMU. If all devices share the same protection domain
this can lead to data corruption and data loss. Prevent this by putting
each device into its own protection domain per default.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
this compiler warning:
arch/x86/kernel/ds.c: In function 'ds_request':
arch/x86/kernel/ds.c:368: warning: 'context' may be used uninitialized in this function
Shows that the code flow in ds_request() is buggy - it goes into
the unlock+release-context path even when the context is not allocated
yet.
First allocate the context, then do the other checks.
Also, take care with GFP allocations under the ds_lock spinlock.
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
dma_mapping_error is an actual function, so fix broken define with a
real inline stub
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Impact: fix incorrectly marked unstable TSC clock
Patch (commit 0d12cdd "sched: improve sched_clock() performance") has
a regression on one of the test systems here.
With the patch, I see:
checking TSC synchronization [CPU#0 -> CPU#1]:
Measured 28 cycles TSC warp between CPUs, turning off TSC clock.
Marking TSC unstable due to check_tsc_sync_source failed
Whereas, without the patch syncs pass fine on all CPUs:
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Due to this, TSC is marked unstable, when it is not actually unstable.
This is because syncs in check_tsc_wrap() goes away due to this commit.
As per the discussion on this thread, correct way to fix this is to add
explicit syncs as below?
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
reset_value was changed from long to u64 in commit
b991702884 (oprofile: Implement Intel
architectural perfmon support)
But dynamic allocation of this array use a wrong type (long instead of
u64)
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch makes do_hw_reset the default reboot behavior when nothing
else matches. This restores reboot functionality on gumstix basix
devices where reboot=cold is the default boot argument.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: fix es7000 build
CC arch/x86/kernel/es7000_32.o
arch/x86/kernel/es7000_32.c: In function find_unisys_acpi_oem_table:
arch/x86/kernel/es7000_32.c:255: error: implicit declaration of function acpi_get_table_with_size
arch/x86/kernel/es7000_32.c:261: error: implicit declaration of function early_acpi_os_unmap_memory
arch/x86/kernel/es7000_32.c: In function unmap_unisys_acpi_oem_table:
arch/x86/kernel/es7000_32.c:277: error: implicit declaration of function __acpi_unmap_table
make[1]: *** [arch/x86/kernel/es7000_32.o] Error 1
we applied one patch out of order...
| commit a73aaedd95
| Author: Yinghai Lu <yhlu.kernel@gmail.com>
| Date: Sun Sep 14 02:33:14 2008 -0700
|
| x86: check dsdt before find oem table for es7000, v2
|
| v2: use __acpi_unmap_table()
that patch need:
x86: use early_ioremap in __acpi_map_table
x86: always explicitly map acpi memory
acpi: remove final __acpi_map_table mapping before setting acpi_gbl_permanent_mmap
acpi/x86: introduce __apci_map_table, v4
submitted to the ACPI tree but not upstream yet.
fix it until those patches applied, need to revert this one
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The original incorrect configuration caused GPIO79_nCS_3 being overriden,
thus resulted in the NAND flash not being detected. The real PSKTSEL pin
is on GPIO104 instead of GPIO79.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Fix a problem where ds_request() returned an error without releasing the
ds lock.
Reported-by: Stephane Eranian <eranian@gmail.com>
Signed-off-by: Markus Metzger <markus.t.metzger@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sh/for-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: Reorder the SCxTDR write after the TDxE clear.
sh: __copy_user function can corrupt the stack in case of exception
sh: Fixed the TMU0 reload value on resume
sh: Don't factor in PAGE_OFFSET for valid_phys_addr_range() check.
sh: early printk port type fix
i2c: fix i2c-sh_mobile rx underrun
sh: Provide a sane valid_phys_addr_range() to prevent TLB reset with PMB.
usb: r8a66597-hcd: fix wrong data access in SuperH on-chip USB
fix sci type for SH7723
serial: sh-sci: fix cannot work SH7723 SCIFA
sh: Handle fixmap TLB eviction more coherently.
This reverts commit e51af66308, which was
wrongly hoovered up and submitted about a month after a better fix had
already been merged.
The better fix is commit cbda1ba898
("PCI/iommu: blacklist DMAR on Intel G31/G33 chipsets"), where we do
this blacklisting based on the DMI identification for the offending
motherboard, since sometimes this chipset (or at least a chipset with
the same PCI ID) apparently _does_ actually have an IOMMU.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 69961c3752 ("[PATCH] m68k/Atari:
Interrupt updates") added a BUG_ON() with an incorrect upper bound
comparison, which causes an early crash on VME boards, where IRQ_USER is
8, cnt is 192 and NR_IRQS is 200.
Reported-by: Stephen N Chivers <schivers@csc.com.au>
Tested-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The uname system call for 64 bit compares current->personality without
masking the upper 16 bits. If e.g. READ_IMPLIES_EXEC is set the result
of a uname system call will always be s390x even if the process uses
the s390 personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cpu_coregroup_map used to grab a mutex on s390 since it was only
called from process context.
Since c7c22e4d5c "block: add support
for IO CPU affinity" this is not true anymore.
It now also gets called from softirq context.
To prevent possible deadlocks change this in architecture code and
use a spinlock instead of a mutex.
Cc: stable@kernel.org
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With CONFIG_IRQSOFF_TRACER the trace_hardirqs_off() function includes
a call to __builtin_return_address(1). But we calltrace_hardirqs_off()
from early entry code. There we have just a single stack frame.
So this results in a kernel stack backchain walk that would walk beyond
the kernel stack. Following the NULL terminated backchain this results
in a lowcore read access.
To fix this we simply call trace_hardirqs_off_caller() and pass the
current instruction pointer.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Disable tracing on idle psw. Otherwise it would give us huge
preempt off times for idle. Which is rather pointless.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch/s390/kernel/built-in.o: In function `cleanup_io_leave_insn':
mem_detect.c:(.text+0x10592): undefined reference to `lockdep_sys_exit'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
add_active_range() expects start_pfn + size as end_pfn value, i.e. not
the pfn of the last page frame but the one behind that.
We used the pfn of the last page frame so far, which can lead to a
BUG_ON in move_freepages(), when the kernelcore parameter is specified
(page_zone(start_page) != page_zone(end_page)).
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Various printk format string in code used by the Xilinx Virtex platform
are not 32-bit/64-bit safe. Add correct casting to fix the bugs.
Reported-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Without this patch it is possible to select drivers which require
bestcomm support without bestcomm support being selected. This
patch reworks the bestcomm dependencies to ensure the correct
bestcomm tasks are always enabled.
Reported-by: Hans Lehmann <hans.lehmann@ritter-elektronik.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 2d3854a37e ("cpumask: introduce new
API, without changing anything") introduced a build breakage on parisc.
This trivial patch fixes it.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kyle Mc Martin <kyle@hera.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Those cores use the 440A type machine check (ie, they have
MCSRR0/MCSRR1). They thus need to call the appropriate fixup
function to hook the right variant of the exception.
Without this, all machine checks become fatal due to loss
of context when entering the exception handler.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
If the size of DRAM is not an exact power of two, we may not have
covered DRAM in its entirety with large 16 and 4 MiB pages. If that
is the case, we can get non-recoverable page faults when doing the
final PTE mappings for the non-large page PTEs.
Consequently, we restrict the top end of DRAM currently allocable
by updating '__initial_memory_limit_addr' so that calls to the LMB to
allocate PTEs for "tail" coverage with normal-sized pages (or other
reasons) do not attempt to allocate outside the allowed range.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
FLASH_* and EPROM_* constants are unused, and clash with drivers:
drivers/atm/ambassador.h:257:1: warning: "FLASH_BASE" redefined
drivers/atm/ambassador.h:258:1: warning: "FLASH_SIZE" redefined
drivers/atm/iphase.h:332:1: warning: "EPROM_SIZE" redefined
so remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mm/dma-mapping.c: In function `dma_sync_sg_for_cpu':
arch/arm/mm/dma-mapping.c:588: warning: statement with no effect
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Under qemu there is a race between the TDxE read-and-clear and the SCxTDR
write. While on hardware it can be gauranteed that the read-and-clear
will happen prior to the character being written out, no such assumption
can be made under emulation. As this path happens with IRQs off and the
hardware itself doesn't care about the ordering, move the SCxTDR write
until after the read-and-clear.
Signed-off-by: Vladimir Prus <vladimir@codesourcery.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The __copy_user function can corrupt the stack in the case of a
non-trivial length of data, and either of the first two move instructions
cause an exception. This is because the fixup for these two instructions
is mapped to the no_pop case, but these instructions execute after the
stack is pushed.
This change creates an explicit NO_POP exception mapping macro, and uses
it for the two instructions executed in the trivial case where no stack
pushes occur.
More information at ST Linux bugzilla:
https://bugzilla.stlinux.com/show_bug.cgi?id=4824
Signed-off-by: Dylan Reid <dylan_reid@bose.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the TMU0 interrupt frequency on suspend/resume.
During the resume the kernel reprograms the TMU0.ClockEvent mode
but if the mode is periodic than the TMU0.TCOR is updated with
a random wrong value without taking care latest valid saved value.
There was no problem with No_HZ system where TMU0.TCOR isn't used.
Signed-off-by: Francesco M. Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes tty compile warnings as sugested by Alan Cox:
CC drivers/char/n_tty.o
drivers/char/n_tty.c: In function ‘normal_poll’:
drivers/char/n_tty.c:1555: warning: array subscript is above array bounds
drivers/char/n_tty.c:1564: warning: array subscript is above array bounds
drivers/char/n_tty.c: In function ‘read_chan’:
drivers/char/n_tty.c:1269: warning: array subscript is above array bounds
CC drivers/char/tty_ioctl.o
drivers/char/tty_ioctl.c: In function ‘set_termios’:
drivers/char/tty_ioctl.c:533: warning: array subscript is above array
bounds
drivers/char/tty_ioctl.c:537: warning: array subscript is above array
bounds
drivers/char/tty_ioctl.c: In function ‘tty_mode_ioctl’:
drivers/char/tty_ioctl.c:662: warning: array subscript is above array
bounds
drivers/char/tty_ioctl.c:892: warning: array subscript is above array
bounds
drivers/char/tty_ioctl.c:896: warning: array subscript is above array
bounds
drivers/char/tty_ioctl.c:577: warning: array subscript is above array
bounds
drivers/char/tty_ioctl.c:928: warning: array subscript is above array
bounds
drivers/char/tty_ioctl.c:934: warning: array subscript is above array
bounds
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous patch to make CONFIG_NUMA on x86_32 depend on BROKEN
turned out to be unnecessary, after all, since the source of the
hibernation vs CONFIG_NUMA problem turned out to be the fact that
we didn't take the NUMA KVA remapping into account in the
hibernation code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix crash during hibernation on 32-bit NUMA
The NUMA code on x86_32 creates special memory mapping that allows
each node's pgdat to be located in this node's memory. For this
purpose it allocates a memory area at the end of each node's memory
and maps this area so that it is accessible with virtual addresses
belonging to low memory. As a result, if there is high memory,
these NUMA-allocated areas are physically located in high memory,
although they are mapped to low memory addresses.
Our hibernation code does not take that into account and for this
reason hibernation fails on all x86_32 systems with CONFIG_NUMA=y and
with high memory present. Fix this by adding a special mapping for
the NUMA-allocated memory areas to the temporary page tables created
during the last phase of resume.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: struct device - replace bus_id with dev_name(), dev_set_name()
iop-adma: use iop_paranoia() for debug BUG_ONs
iop-adma: add a dummy read to flush next descriptor update
Don't do misalignment handling for userspace misalignment faults: just
generate an appropriate SIGBUS instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't handle the misaligned loading and storing of the SP register as in C code
that's most certainly a compiler bug.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support misalignment handling for instructions that have kernel SP-based
address operands, including fixing those that include IMM8 or IMM16
displacements.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix misalignment handling for an address calculated from the sum of two
registers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correctly handle misalignment in MOV instructions with postinc-with-immediate
addressing mode operands. In these, the immediate value is the increment to
be applied the address register, not the displacement to the address.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Perform misalignment fixups of the MOV_Lcc instructions (move postinc memory
to register and conditionally loop).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow misalignment fixup in interrupt handling in the MN10300 arch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix misalignment handling of operands with register postincrement addressing.
The flag to indicate that postincrement is required should not be interpreted
as an specification of a value to be added to the address.
Also add BUGs to catch unimplemented parameter markings in the opcodes table.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extract the displacement from an MN10300 instruction correctly in the
misalignment fixup handler.
The code should extract the displacement in LSB order, not MSB order.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add further misalignment fixup support to the MN10300 arch, notably for ABS32
and SP+disp addressing.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the MN10300 misalignment handler a little by:
(1) Use ilog2() rather than doing implementing log2() locally.
(2) Make format_tbl[] const and static.
(3) Making the debugging prints more consistent.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: Fix pit memory leak if unable to allocate irq source id
KVM: ia64: fix vmm_spin_{un}lock for !CONFIG_SMP
KVM: VMX: Set IGMT bit in EPT entry
KVM: Require the PCI subsystem
x86: KVM guest: fix section mismatch warning in kvmclock.c
KVM: ia64: Use guest signal mask when blocking
KVM: MMU: increase per-vcpu rmap cache alloc size
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (47 commits)
ACPI: pci_link: remove acpi_irq_balance_set() interface
fujitsu-laptop: Add DMI callback for Lifebook S6420
ACPI: EC: Don't do transaction from GPE handler in poll mode.
ACPI: EC: lower interrupt storm treshold
ACPICA: Use spinlock for acpi_{en|dis}able_gpe
ACPI: EC: restart failed command
ACPI: EC: wait for last write gpe
ACPI: EC: make kernel messages more useful when GPE storm is detected
ACPI: EC: revert msleep patch
thinkpad_acpi: fingers off backlight if video.ko is serving this functionality
sony-laptop: fingers off backlight if video.ko is serving this functionality
msi-laptop: fingers off backlight if video.ko is serving this functionality
fujitsu-laptop: fingers off backlight if video.ko is serving this functionality
eeepc-laptop: fingers off backlight if video.ko is serving this functionality
compal: fingers off backlight if video.ko is serving this functionality
asus-acpi: fingers off backlight if video.ko is serving this functionality
Acer-WMI: fingers off backlight if video.ko is serving this functionality
ACPI video: if no ACPI backlight support, use vendor drivers
ACPI: video: Ignore devices that aren't present in hardware
Delete an unwanted return statement at evgpe.c
...
With the PMB enabled, only P1SEG and up are covered by the PMB mappings,
meaning that situations where out-of-bounds physical addresses are read
from will lead to TLB reset after the PMB miss, allowing for use cases
like dd if=/dev/mem to reset the TLB.
Fix this up to make sure the reference is between __MEMORY_START (phys)
and __pa(high_memory). This is coherent across all variants of sh/sh64
with and without MMU, though the PMB bug itself is only applicable to
SH-4A parts.
Reported-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes sci type of SH7723 from PORT_SCI to PORT_SCIFA.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.
x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing. But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.
It's better for the driver to figure this out at init-time. If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the case of !CONFIG_SMP, raw_spinlock_t is empty and the spinlock functions
don't build. Fix by defining spinlock functions for the uniprocessor case.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is a potential issue that, when guest using pagetable without vmexit when
EPT enabled, guest would use PAT/PCD/PWT bits to index PAT msr for it's memory,
which would be inconsistent with host side and would cause host MCE due to
inconsistent cache attribute.
The patch set IGMT bit in EPT entry to ignore guest PAT and use WB as default
memory type to protect host (notice that all memory mapped by KVM should be WB).
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
WARNING: arch/x86/kernel/built-in.o(.text+0x1722c): Section mismatch
in reference from the function kvm_setup_secondary_clock() to the
function .devinit.text:setup_secondary_APIC_clock()
The function kvm_setup_secondary_clock() references
the function __devinit setup_secondary_APIC_clock().
This is often because kvm_setup_secondary_clock lacks a __devinit
annotation or the annotation of setup_secondary_APIC_clock is wrong.
Signed-off-by: Md.Rakib H. Mullick <rakib.mullick@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: handle HRTIMER_CB_IRQSAFE_UNLOCKED correctly from softirq context
nohz: disable tick_nohz_kick_tick() for now
irq: call __irq_enter() before calling the tick_idle_check
x86: HPET: enter hpet_interrupt_handler with interrupts disabled
x86: HPET: read from HPET_Tn_CMP() not HPET_T0_CMP
x86: HPET: convert WARN_ON to WARN_ON_ONCE
Before a vcpu blocks, it should switch to the guest signal mask to allow
signals to unblock it.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The page fault path can use two rmap_desc structures, if:
- walk_addr's dirty pte update allocates one rmap_desc.
- mmu_lock is dropped, sptes are zapped resulting in rmap_desc being
freed.
- fetch->mmu_set_spte allocates another rmap_desc.
Increase to 4 for safety.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Impact: build/boot fix for x86/Voyager
This change:
| commit 3d44223327
| Author: Jens Axboe <jens.axboe@oracle.com>
| Date: Thu Jun 26 11:21:34 2008 +0200
|
| Add generic helpers for arch IPI function calls
didn't wire up the voyager smp call function correctly, so do that
here. Also make CONFIG_USE_GENERIC_SMP_HELPERS a def_bool y again,
since we now use the generic helpers for every x86 architecture.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <Jens.Axboe@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Turned off CONFIG_PCI_LEGACY and turned on EXT4, and otherwise mostly
took the defaults. This also updates ppc6xx_defconfig, which covers
the 6xx/7xx/7xxx-based embedded boards.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new context may not be 16-byte aligned, so the real address of the
mcontext structure should be read from the uc_regs pointer instead of
directly using the (unaligned) uc_mcontext field.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While investigating the failure of hibernation on 32-bit x86 with
CONFIG_NUMA set, as described in this message
http://marc.info/?l=linux-kernel&m=122634118116226&w=4
I asked some people for help and I was told that it wasn't really
worth the effort, because CONFIG_NUMA was generally broken on 32-bit
x86 systems and it shouldn't be used in such configs. For this
reason, make CONFIG_NUMA depend on BROKEN instead of EXPERIMENTAL on
x86-32.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Pavel Machek <pavel@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 8dd9453737.
This fixes a boot failure reported by Robert Reif.
The code above the section change expects to fallthrough, so
we can't make such a section change here.
Some functions that may be called from this handler require that
interrupts are disabled. Also, combining IRQF_DISABLED and
IRQF_SHARED does not reliably disable interrupts in a handler, so
remove IRQF_SHARED from the irq flags (this irq is not shared anyway).
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Cc: "Will Newton" <will.newton@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In hpet_next_event() we check that the value we just wrote to
HPET_Tn_CMP(timer) has reached the chip. Currently, we're checking that
the value we wrote to HPET_Tn_CMP(timer) is in HPET_T0_CMP, which, if
timer is anything other than timer 0, is likely to fail.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is possible to flood the console with call traces if the WARN_ON
condition is true because of the frequency with which this function is
called.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There was a race in the kmap_coherent() implementation. While we
guarded against preemption, there was nothing preventing eviction of
the pre-faulted fixmap entry from the UTLB. Under certain workloads
this would result in the fixmap entries used for cache colouring being
evicted from the UTLB in the midst of a copy_page().
In addition to pre-faulting, we also make sure to preserve the PTEs
in the kernel page table and introduce a cached PTE for kmap_coherent()
usage. This follows a similar change on MIPS ("[MIPS] Fix aliasing bug
in copy_to_user_page / copy_from_user_page").
Reported-by: Hideo Saito <saito@densan.co.jp>
Reported-by: CHIKAMA Masaki <masaki.chikama@gmail.com>
Tested-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
setup_ioapic_dest() is called after the non boot cpus have been
brought up. It sets the irq affinity of all already configured
interrupts to all cpus and ignores affinity settings which were
done by the early bootup code.
If the IRQ_NO_BALANCING or IRQ_AFFINITY_SET flags are set then use the
affinity mask from the irq descriptor and not TARGET_CPUS.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
a new file was accidentally added to include/asm-x86;
move it to the new arch/x86/include/asm location
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>