When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oops, a stupid mistake in the original patch which adds coex 3-wire
support. Bluetooth priority gpio needs to be gpio 7.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This subsystem id will be used later to turn on the btcoex
support.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
apply the conformance test limits (CTL) stored in the eeprom upon
the values calculated for the tx power (ar->power_*).
This is based on the implementation in the vendor driver
(hal/hpmain.c, line 3700 ff.) with one difference:
If any ctl mode isn't found in the eeprom, we fall back to the "lower",
legacy modes (5GHT20,11A or 2GHT20,11G,11B). Otus only did 5GHT20->11A.
Currently CTL are applied for the FCC group only.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ar9170 driver needs the defines for conformance test limit groups
and cannot include regd_common.h
Signed-off-by: Joerg Albert <jal2@gmx.de>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports some code from the vendor driver, which is
supposed to upload the right calibration values for the
chosen frequency.
In theory, this should give a better range and throughput
for all users with the open, or one-stage firmware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHANNEL_G has to be set for 2GHZ channels since
IS_CHAN_G() checks for this in channelFlags and not in
chanmode. To make things messier, ath9k_hw_process_ini()
checks for CHANNEL_G in chanmode and not in channelFlags.
The supreme, brain-searing fix is to set the
flag in both cases.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BAR frames have to be sent to mac80211 only if the
current channel is HT. Also, move the macro to
enum ath9k_rx_filter.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k ahb requests an IRQ and indicates 'ath9k' claimed it,
ath9k pci requests an IRQ and indicates 'ath' claims it;
since 'ath' is another module sync both ahb and pci to claim
the irq using 'ath9k'.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've cleaned up ath_init_device() and its children enough
to pass meaninful errors back from probe. When this fails
it means our device could not be initialized and a meaninful
error will have been passed.
Do the same for request_irq() and also synchronize the error
messages while at it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The -ENOMEM was never being passed on failure.
While at it use dev_err() as ahb does upon failure.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the initialisation of some PHY registers
from the modal_header[] values in the EEPROM
(see otus/hal/hpmain.c, line 333 ff.)
Signed-off-by: Joerg Albert <jal2@gmx.de>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As generic hw timer interrupt handler is moved to tasklet,
we no more need to call spin_lock_irqsave().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point handling this in hard irq, move it to
tasklet.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing an RTC reset when DMA is active may corrupt memory,
make sure no DMA is active at this moment by doing an
AHB reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5K_SREV is available even if the chip has been put to sleep. Relying
on the chip register allows binding non-standard PCI IDs by
echo VENDOR_ID PRODUCT_ID >/sys/bus/pci/drivers/ath5k/new_id
without having to specify the driver data as well.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The `val' variable in ath5k_eeprom_read_turbo_modes() is used
uninitialized. gcc 4.4.1 with -fno-inline-functions-called-once reports
it:
eeprom.c: In function 'ath5k_eeprom_read_turbo_modes':
eeprom.c:441: warning: 'val' may be used uninitialized in this function
Comparing the code to the Atheros HAL, it's clear that the split between
ath5k_eeprom_read_modes() and ath5k_eeprom_read_turbo_modes() was
incorrect.
The Atheros HAL reads both turbo and non-turbo data from EEPROM in one
function. Some turbo mode parameters are derived from the same EEPROM
values as non-turbo parameters, just from different bits.
Merge ath5k_eeprom_read_turbo_modes() into ath5k_eeprom_read_modes() to
fix the warning. The actual values and offsets have been cross-checked
against Atheros HAL.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Pavel Roskin noted, the check for mac version as copied from
legacy_hal made no sense. This replaces it with the equivalent
and makes up a suitable #define for the mac version legacy_hal
checked.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3-wire bluetooth coex support for AR9285.
This support can be enabled through btcoex_enable modparam.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need a hw cap bit for btcoex anymore as btcoex scheme type
is enough to do this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also define macros for wlanactive and btactive (5 & 6) gpios.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure btcoex register configured with appropriate values
after it is initialized with the default values from initvals.h
during reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function currently does initialization + enable the
btcoex support. Split it into two logical functions which
does the above operations separately. Btcoex initialization
is done during attach time and enabling this feature is done
in start(). Also, add code to disable btcoex support in stop().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When dumping register contents, HW has to be awake.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PA Calibration is not needed for high power solutions.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* First PA driver (PDPADRV1) was not powered down properly.
* Compensation capacitor for dynamic PA was programmed incorrectly.
Also, remove a stray REG_READ.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PA calibration need not be done if the offset is not varying.
The current logic does PA calibration even if the offset is the
same.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent a read of powInfo[-1] in the first iteration.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent ath5k hardware is capable of doing CCMP acceleration.
Enable it for the cards that support it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Save a memcpy by just storing updates directly in the skb
control block.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch, a compaq c700 can turn on the wifi led.
The array of compatible devices now includes the hardware
present in this computer, as well as the led pin and
polarity.
Signed-off-by: Marcos Chaparro <nitrousnrg@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The maze of if() statements in configure_filter is confusing.
Reorganizing it as a switch statement makes it more apparent what
is going on and reveals several suspicious settings. This has no
functional changes, though it does remove some redundant flags
that are set earlier.
Also now that we can sleep, protect sc->filter_flags with the
sc lock.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add beacon control by BSS_CHANGED_BEACON_ENABLED and
bss_conf->enable_beacon from mac80211.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX chainmasks were set to 1x1 during scanning.
Configure them properly with the values retrieved from
the EEPROM.
Also, this requires scan_start/scan_end callbacks to be
locked with sc->mutex.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for FIF_OTHER_BSS was missing. This patch adds support for this
filtering mode which in turn resolves a problem where mesh interfaces would not
receive broadcast traffic.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Other than ns_avgbrssi (Average beacon rssi) no data of
ath9k_node_stats is being used anywhere. Nuke this structure
and move its only useful member to ar5416Anistate. Also cleanup
this redundant data in ath_softc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the beacon rssi that LPF gives is divided and rounded
up by ATH_RSSI_EP_MULTIPLIER twice. This will leave the incorrect rssi
in ANI. Having correct rssi in ANI fixes the connection stability at
< 30dB rssi range. This patch removes the unncessary computation of average
rssi over already valid average rssi. Also removes the redundant macros to
find average rssi.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thanks to "mac80211: allow configure_filter callback to sleep",
we no longer have to defer the work to the workqueue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the shared regulatory structure into the
common structure. We will use this ongoing for common
data.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k_stop(), tx_complete_work was being cancelled twice.
This patch fixes it. Also, locking sc->mutex should be done
at the beginning.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
