#TOKEN
#	Name  = "CSPLIB_SUPPORT"
#	Value  = "0"
#	Help  = "Main switch to enable CSP Library support in Project"
#	TokenType = Boolean
#	TargetEQU = Yes
#	TargetMAK = Yes
#End

TOKEN
	Name  = "===================== CSP.sdl ====================="
	Value  = "==========================================================="
	TokenType = Expression
End

#TOKEN
#	Name  = "PCIE_BASE_ADDRESS"
#	Value  = "$(PCIEX_BASE_ADDRESS)"
#	Help  = "Specify the Base address where PCI Config space is mapped.\ Set to 0 if PCI Express access functions are not supported."
#	TokenType = Integer
#	TargetH = Yes
#End

TOKEN
	Name  = "DEFAULT_ACPI_SPCR_CONSOLE_REDIRECTION_ENABLE"
	Value  = "0"
	TokenType = Boolean
	TargetH = Yes
End

#TOKEN
#	Name  = "duty_offset"
#	Value  = "1"
#	Help  = "The zero-based index of where the processor's duty cycle setting is within the processor's P_CNT register.\(for more information, ACPI SPEC)."
#	TokenType = Integer
#	TargetH = Yes
#	Range  = "0-0xf0"
#End

#TOKEN
#	Name  = "duty_width"
#	Value  = "3"
#	Help  = "The bit width of the processor's duty cycle setting value in the P_CNT register. Each processor's duty cycle setting\allows the software to select a nominal processor frequency below its absolute frequency.\(for more information, ACPI SPEC)."
#	TokenType = Integer
#	TargetH = Yes
#	Range  = "0-0xff: depends on 'duty_offset'"
#End

PcdMapping
    Name  = "AmiPcdPcieBaseAddressBuffer"
    GuidSpace  = "gAmiModulePkgTokenSpaceGuid"
    PcdType  = "PcdsDynamicDefault"
    DataType  = "Pointer"
    Value  = "{0x0,0x0,0x0,0xF8,0x0,0x0,0x0,0x0}"
    Offset  = 00h
    Length  = 08h
    Help  = "<PORTING REQUIRED: sync PCIEX_BASE_ADDRESS>\Value must be byte sequence of AMI_MAX_NUMBER_OF_PCI_SEGMENTS UINT64 bit values in array./Length must be (sizeof(UINT64)*$(AMI_MAX_NUMBER_OF_PCI_SEGMENTS))"
    TargetDSC = Yes
End

TOKEN
	Name  = "===================== AMD SB900 module ====================="
	Value  = "==========================================================="
	TokenType = Expression
End

#TOKEN
#	Name  = "CIMX_MISC_UI_SUPPORT"
#	Value  = "0"
#	Help  = "CIMx RAID UI bin support"
#	TokenType = Boolean
#	TargetMAK = Yes
#End

TOKEN
	Name  = "SB_LPC_PORT80_SUPPORT"
	Value  = "1"
	Help  = "LPC Port 80 support"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

#TOKEN
#	Name  = "SB_RAID5_SUPPORT"
#	Value  = "0"
#	Help  = "On:Platform support Raid5\OFF:Platform don't support Raid5"
#	TokenType = Boolean
#	TargetMAK = Yes
#	TargetH = Yes
#End

TOKEN
	Name  = "XHCI_EVENT_SERVICE_MODE"
	Value  = "1"
	Help  = "This token controlls xHCI event service mode.\0 - Use periodic timer SMI.\1 - Use xHCI hardware SMI.\2 - Both periodic timer SMI and se xHCI hardware SMI."
	TokenType = Integer
	TargetH = Yes
	Range  = "0..2"
End

#TOKEN
#	Name  = "SmBus_SUPPORT"
#	Value  = "1"
#	Help  = "Main switch to enable SmBus support in Project"
#	TokenType = Boolean
#	TargetEQU = Yes
#	TargetMAK = Yes
#End

TOKEN
    Name  = "=====================SPI Interface - Source ====================="
    Value  = "==========================================================="
    TokenType = Expression
End

TOKEN
	Name  = "YANGTZE_SPI"
	Value  = "1"
	Help  = "Switch to SPI support for YangTze."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
    Name  = "REG80_FIFO_SUPPORT"
    Value  = "1"
    Help  = "Switch to use 64 bytes FIFO at register 0x80"
    TokenType = Boolean
    TargetH = Yes
End

TOKEN
    Name  = "LPCFlash_SUPPORT"
    Value  = "0"
    Help  = "Main switch to enable LPC Flash support in Project"
    TokenType = Boolean
End

TOKEN
    Name  = "STDFlash_SUPPORT"
    Value  = "0"
    Help  = "Main switch to enable STD Flash support in Project"
    TokenType = Boolean
End

#TOKEN
#	Name  = "===================== GNB.sdl ====================="
#	Value  = "==========================================================="
#	TokenType = Expression
#End
#
#TOKEN
#	Name  = "PCIEX_BASE_ADDRESS"
#	Value  = "0xF8000000"
#	Help  = "Contains the base address programmed for PCI Express. \Set this value to 0 if PCI Express support is not present. \Enables/disables PCI configuration access through memory. \Make sure PCIEX_BASE_ADDRESS is set appropriately. \If PCI is accessed through PCI \config mechanism then the maximum register offset that can be accessed is 256."
#	TokenType = Integer
#	TargetEQU = Yes
#	TargetH = Yes
#End
#
#TOKEN
#	Name  = "===================== AGESA ====================="
#	Value  = "==========================================================="
#	TokenType = Expression
#End
#
#TOKEN
#	Name  = "IGNORE_SPD_CHECKSUM"
#	Value  = "1"
#	Help  = "Set to ignore SPD checkum. (DIMMS may return an incorrect SPD Checksum) "
#	TokenType = Boolean
#	TargetEQU = Yes
#End

TOKEN
	Name  = "===================== ACPI ====================="
	Value  = "==========================================================="
	TokenType = Expression
End

#TOKEN
#	Name  = "FEC00000_APIC_AUTODETECT"
#	Value  = "1"
#	Help  = "This will Auto Detect IO/APIC(s) which resides in MMIO region from 0xFEC0_0000  to 0xFED0_0000-1.\\ If set to 'off' ACPI initialization software will assume - system has one IO/APIC\with address provided in 'APCB' token."
#	TokenType = Boolean
#	TargetH = Yes
#	Range  = "On - Off"
#End

TOKEN
	Name  = "IO_APIC_BASE_ADDRESS_TOP"
	Value  = "0xFEC10000"
	Help  = "Platform defined APIC search top of APIC address"
	TokenType = Integer
	TargetH = Yes
	Token = "FEC00000_APIC_AUTODETECT" "=" "1"
End

TOKEN
	Name  = "IO_APIC_VERSION_PARAMETER"
	Value  = "0x22"
	Help  = "IOAPIC/IOSAPIC revision BOUNDARY. For Intel it is should be 0x21. Clone and reasign if different"
	TokenType = Integer
	TargetH = Yes
	Token = "FEC00000_APIC_AUTODETECT" "=" "1"
End

TOKEN
	Name  = "IRQ_09_POLARITY"
	Value  = "3"
	Help  = "0 = Conforms to specifications of bus.\1 = Active High.\3 = Active Low."
	TokenType = Integer
	TargetH = Yes
	Range  = "0, 1 or 3. 2-reserved"
	Token = "IRQ_09_OVERRIDE_ENABLE" "=" "1"
End

#TOKEN
#	Name  = "MPS_TABLE_SUPPORT"
#	Value  = "0"
#	Help  = "Main switch to enable MPS V 1.4 Table support in Project"
#	TokenType = Boolean
#	TargetEQU = Yes
#	TargetMAK = Yes
#	TargetH = Yes
#End

TOKEN
	Name  = "ACPI_PM_PROFILE"
	Value  = "2"
	Help  = "Power Management Profile ACPI 2.0\See acpi20.h"
	TokenType = Integer
	TargetH = Yes
	Range  = "0-8 0 = Unspecified; 1 = Desktop; 2 = Mobile; 3 = Workstation; 4 = Enterprise Server; 5 = SOHO Server; 6 = Application PC; 7 = Performance Server; 8 = Tablet"
	Token = "ACPI_BUILD_TABLES_2_0" "=" "1"
End

TOKEN
	Name  = "FACP_FLAG_TMR_VAL_EXT"
	Value  = "1"
	Help  = "(EIP36898+)A zero indicates TMR_VAL is implemented as a \24-bit value. A one indicates TMR_VAL is \implemented as a 32-bit value. The TMR_STS \bit is set when the most significant bit of the \TMR_VAL toggles."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "A_S1"
	Value  = "0"
	Help  = "S1 Sleep state enabled in BIOS"
	TokenType = Boolean
	TargetMAK = Yes
End

#TOKEN
#	Name  = "===================== CPU.sdl ====================="
#	Value  = "==========================================================="
#	TokenType = Expression
#End

TOKEN
	Name  = "===================== PciBus.sdl ====================="
	Value  = "==========================================================="
	TokenType = Expression
End

PCIDEVICE
	Title  = "PciHost (Virtual)"
	Attribute  = "0x2"
	Dev_type  = "HostBridge"
	Dev  = 00h
	SleepNum  = 03h
	ASLfile  = "'AmiChipsetModulePkg/ASL/AmdASLLIB.asl;Before Pci Tree','AmiModulePkg/ACPI/AMLUPD.ASL;Before Pci Tree'"
	ASLdeviceName  = "HST0"
	Token = "PCI_FIXED_BUS_ASSIGNMENT" "=" "1"
	DeviceType = OnBoard
	PCIBusSize = 64bit
	ROMMain = No
	Virtual = Yes
	PCIExpress = Yes
	Enforce = Yes
	Help  = "Override ASLLIB.ASL by AMDASLLIB.asl to sync ASL code with AMD demo BIOS."
End

PCIDEVICE
	Title  = "PciHost (Virtual)"
	Attribute  = "0x2"
	Dev_type  = "HostBridge"
	Dev  = 00h
	SleepNum  = 03h
	ASLfile  = "'AmiChipsetModulePkg/ASL/AmdASLLIB.asl;Before Pci Tree','AmiModulePkg/ACPI/AMLUPD.ASL;Before Pci Tree'"
	ASLdeviceName  = "HST0"
	Token = "PCI_FIXED_BUS_ASSIGNMENT" "=" "0"
	DeviceType = OnBoard
	PCIBusSize = 64bit
	ROMMain = No
	Virtual = Yes
	PCIExpress = Yes
	Help  = "Override ASLLIB.ASL by AMDASLLIB.asl to sync ASL code with AMD demo BIOS."
End

TOKEN
	Name  = "===================== USB.sdl ====================="
	Value  = "==========================================================="
	TokenType = Expression
End

TOKEN
	Name  = "UHCI_SUPPORT"
	Value  = "0"
	Help  = "Enable/Disable UHCI controller(s)."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "OHCI_SUPPORT"
	Value  = "0"
	Help  = "Enable/Disable OHCI controller(s)"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "EHCI_SUPPORT"
	Value  = "0"
	Help  = "(Raven/Picasso only XHCI) Enable/Disable EHCI controller(s)"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "XHCI_SUPPORT"
	Value  = "1"
	Help  = "Enable/Disable xHCI controller(s)"
	TokenType = Boolean
	TargetH = Yes
End

#TOKEN
#	Name  = "USB_HOTPLUG_FDD"
#	Value  = "0"
#	Help  = "Includes the support for USB hot plug floppy drive."
#	TokenType = Boolean
#	TargetH = Yes
#End

TOKEN
	Name  = "USB_DEBUG_MESSAGES"
	Value  = "0"
	TokenType = Boolean
	TargetH = Yes
	Token = "DEBUG_CODE" "!=" "0"
End

#TOKEN
#	Name  = "USB_DEBUG_MESSAGES"
#	Value  = "0"
#	TokenType = Boolean
#	TargetH = Yes
#	Token = "AMI_DEBUGGER_SUPPORT" "=" "1"
#	Token = "DEBUG_MODE_dbg" "!=" "0"
#End

#TOKEN
#	Name  = "===================== AHCI Driver ====================="
#	Value  = "==========================================================="
#	TokenType = Expression
#End

#TOKEN
#	Name  = "ICH_SATA_BUS_NUMBER"
#	Value  = "$(FIXED_SATA_BUS_SANDSTONE)"
#	Help  = "Sata BUS number"
#	TokenType = Integer
#	TargetMAK = Yes
#	TargetH = Yes
#End

#TOKEN
#	Name  = "ICH_SATA_DEVICE_NUMBER"
#	Value  = "0x0"
#	Help  = "Sata Device Number"
#	TokenType = Integer
#	TargetMAK = Yes
#	TargetH = Yes
#End

#TOKEN
#	Name  = "ICH_SATA_FUNCTION_NUMBER"
#	Value  = "0x0"
#	Help  = "SATA Function No"
#	TokenType = Integer
#	TargetMAK = Yes
#	TargetH = Yes
#End

TOKEN
	Name  = "===================== USB PEI Support ====================="
	Value  = "==========================================================="
	TokenType = Expression
End

TOKEN
	Name  = "USBPEI_SUPPORT"
	Value  = "1"
	Help  = "Main switch to enable USB PEI support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "OHCI_PEI_SUPPORT"
	Value  = "0"
	Help  = "Enable/Disable OHCI controller(s) in PEI"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
	Token = "USBPEI_SUPPORT" "=" "1"
End

TOKEN
    Name  = "EHCI_PEI_SUPPORT"
    Value  = "0"
    Help  = "Enable/Disable EHCI controller(s) in PEI"
    TokenType = Boolean
    TargetEQU = Yes
    TargetMAK = Yes
    TargetH = Yes
    Token = "USBPEI_SUPPORT" "=" "1"
End

TOKEN
	Name  = "XHCI_PEI_SUPPORT"
	Value  = "1"
	Help  = "Enable/Disable XHCI controller(s) in PEI"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
	Token = "USBPEI_SUPPORT" "=" "1"
End

TOKEN
	Name  = "PEI_XHCI_CONTROLLER_PCI_ADDRESS"
	Value  = "{2, $(FIXED_XHCI_BUS_SANDSTONE), 0x0, 0x3, $(FIXED_XHCI_BUS_SANDSTONE), 0x0, 0x4}"
	Help  = "Default value if XHCI controllers are not supported"
	TokenType = Expression
	TargetH = Yes
	Token = "XHCI_PEI_SUPPORT" "=" "1"
End

TOKEN
    Name  = "PEI_BRIDGE_MMIO_MIN_H"
    Value  = "0xFE"
    Help  = "Bridge mmio resource"
    TokenType = Integer
    TargetH = Yes
    Token = "XHCI_PEI_SUPPORT" "=" "1"
End

TOKEN
    Name  = "PEI_BRIDGE_MMIO_MIN_L"
    Value  = "0x50"
    Help  = "Bridge mmio resource"
    TokenType = Integer
    TargetH = Yes
    Token = "XHCI_PEI_SUPPORT" "=" "1"
End

TOKEN
    Name  = "PEI_BRIDGE_MMIO_MAX_H"
    Value  = "0xFE"
    Help  = "Bridge mmio resource"
    TokenType = Integer
    TargetH = Yes
    Token = "XHCI_PEI_SUPPORT" "=" "1"
End

TOKEN
    Name  = "PEI_BRIDGE_MMIO_MAX_L"
    Value  = "0x90"
    Help  = "Bridge mmio resource"
    TokenType = Integer
    TargetH = Yes
    Token = "XHCI_PEI_SUPPORT" "=" "1"
End



#TOKEN
#	Name  = "PEI_XHCI_CONTROLLER_PCI_REGISTER_VALUES"
#       Value  = "{0, 0x8, 0x1, 0x18, 32, ((($(FIXED_XHCI_BUS_SANDSTONE)<<8)+$(FIXED_XHCI_BUS_SANDSTONE))<<8), 0xFFFFFF}, {0, 0x8, 0x1, 0x20, 16, $(PEI_BRIDGE_MMIO_MIN), 0xFFFF}, {0, 0x8, 0x1, 0x22, 16, $(PEI_BRIDGE_MMIO_MAX), 0xFFFF}, {0, 0x8, 0x1, 0x4, 0x8, 0x6, 0}, {$(FIXED_XHCI_BUS_SANDSTONE), 0x0, 0x3, 0x10, 32, 0xfe700000, 0xFFFFFFFF}, {$(FIXED_XHCI_BUS_SANDSTONE), 0x0, 0x4, 0x10, 32, 0xfe600000, 0xFFFFFFFF},"
#       Value  = "{0}"
#	Help  = "Enable PCIe slot by programming bridge with the secondary/subordinate bus number and memory window.\Information format (AccessWidth is decimal), with a comma at the end:\   {Bus, Device, Function, Register, AccessWidth, BitsToSet, BitsToClear},"
#	TokenType = Expression
#	TargetH = Yes
#	Token = "XHCI_PEI_SUPPORT" "=" "1"
#End

TOKEN
    Name  = "PEI_XHCI_CONTROLLER_PCI_REGISTER_VALUES"
    Value  = "{0x06, 0x00, 0x08, 0x01, 0x18,0x0,0x0,0x0, 32, 0,$(NBIO_FIXED_ONCHIP_BUS_A),$(NBIO_FIXED_ONCHIP_BUS_A),0x0, 0x00,0x0,0x0,0x0,  0x00, 0x08, 0x01, 0x20,0x0,0x0,0x0, 16, $(PEI_BRIDGE_MMIO_MIN_L),$(PEI_BRIDGE_MMIO_MIN_H),0x0,0x0, 0x00,0x0,0x0,0x0,  0x00, 0x08, 0x01, 0x22,0x0,0x0,0x0, 16, $(PEI_BRIDGE_MMIO_MAX_L),$(PEI_BRIDGE_MMIO_MAX_H),0x0,0x0, 0x00,0x0,0x0,0x0,  0x00, 0x08, 0x01, 0x4,0x0,0x0,0x0, 8, 0x06,0x0,0x0,0x0, 0x00,0x0,0x0,0x0,  $(NBIO_FIXED_ONCHIP_BUS_A), 0x0, 0x3, 0x10,0x0,0x0,0x0, 32, 0x00,0x0,0x70,0xFE,  0x00,0x0,0x0,0x0,  $(NBIO_FIXED_ONCHIP_BUS_A), 0x0, 0x4, 0x10,0x0,0x0,0x0, 32, 0x00,0x0,0x60,0xFE,  0x00,0x0,0x0,0x0}"
    Help  = "Enable PCIe slot by programming bridge with the secondary/subordinate bus number and memory window.\Information format (AccessWidth is decimal), with a comma at the end:\   {Count N, (UINT8)Bus#1, (UINT8)Device#1, (UINT8)Function#1, (UINT32)Register#1, (UINT8)AccessWidth#1, (UINT32)BitsToSet#1, (UINT32)BitsToClear#1,....N},"
    TokenType = Expression
    TargetH = Yes
    Token = "XHCI_PEI_SUPPORT" "=" "1"
End



TOKEN
	Name  = "===================== AhciRecovery.sdl ====================="
	Value  = "==========================================================="
	TokenType = Expression
End

TOKEN
	Name  = "ATAPI_RECOVERY_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
	Token = "AhciRecovery_SUPPORT" "=" "1"    
End

TOKEN
	Name  = "===================== SMM ====================="
	Value  = "==========================================================="
	TokenType = Expression
End

TOKEN
	Name  = "SMM_CACHE_SUPPORT"
	Value  = "0"
	Help  = "Enable/disable SMM Cache Support"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

#TOKEN
#	Name  = "ATIS"
#	Value  = "0xB0"
#	Help  = "ATI Software SMI"
#	TokenType = Integer
#	TargetASL = Yes
#	TargetH = Yes
#End

TOKEN
	Name  = "MAX_MANAGED_CMOS_ADDRESS"
	Value  = "256"
	Help  = "Last CMOS address + 1 used to specify the maximum address that is managed by CMOS Manager. \\Note: the region starting at FIRST_MANAGED_CMOS_ADDRESS and ending at MAX_MANAGED_CMOS_ADDRESS - 1 represents the managed region."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "PROCESSOR_INFO"
	Value  = "0"
	Help  = "ON  -> Processor Information (Type 4) structure will be present\OFF -> Processor Information (Type 4) structure will not be present\The number of CPU is defined in CPU.SDL as NCPU.\Total number of processors will be NCPU ( specified in CPU.SDL) \Currenty there is support for 4 Processors. \To support more processores modify in SMBDESC.DEF and SMBIOS.SDL"
	TokenType = Boolean
	TargetEQU = Yes
End

TOKEN
	Name  = "S3_BASE_MEMORY_SIZE"
	Value  = "0x100000"
	Help  = "Number of bytes for S3 resume base memory."
	TokenType = Integer
	TargetH = Yes
	Range  = "0x40000 = 256K, increase/decrease it in units of 0x1000 = 4K"
End

TOKEN
	Name  = "S3_BASE_MEMORY_SIZE"
	Value  = "0x100000"
	Help  = "Number of bytes for S3 resume base memory."
	TokenType = Integer
	TargetH = Yes
	Range  = "0x40000 = 256K, increase/decrease it in units of 0x1000 = 4K"
	Token = "AMI_DEBUG_RX_IN_S3_SUPPORT" "=" "1"
End

#TOKEN
#	Name  = "IDE_CONTROLLER_LOCATION"
#	Value  = "{0, 0x11, 0}"
#	Help  = "Bus, Device and Function of the First IDE (SATA) controller."
#	TokenType = Expression
#	TargetH = Yes
#	Token = "ACOUSTIC_MANAGEMENT_DRIVER_SUPPORT" "=" "1"
#End

#TOKEN
#	Name  = "SECOND_CONTROLLER_LOCATION"
#	Value  = "{0, 0x14, 1}"
#	Help  = "Location of second IDE (SATA) controller (if any)."
#	TokenType = Expression
#	TargetH = Yes
#	Token = "ACOUSTIC_MANAGEMENT_DRIVER_SUPPORT" "=" "1"
#End

#TOKEN
#    Name  = "===================== SB700Spi ====================="
#    Value  = "==========================================================="
#    TokenType = Expression
#End
#
#TOKEN
#    Name  = "ENABLE_ROM_CACHE_IN_DXE"
#    Value  = "0"
#    Help  = "Switch to enable ROM cache in DXE"
#    TokenType = Boolean
#    TargetH = Yes
#End

TOKEN
	Name  = "===================== TCG ====================="
	Value  = "==========================================================="
	TokenType = Expression
End

TOKEN
	Name  = "TCGSMIPORT"
	Value  = "$(SW_SMI_IO_ADDRESS)"
	Help  = "IO port used to generate software SMI."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "TCGSMIDATAPORT"
	Value  = "$(SW_SMI_IO_ADDRESS) + 1"
	Help  = "IO port used to generate software SMI."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "NO_SIO_SUPPORT"
	Value  = "1"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "NO_SIO_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
	Token = "SIO_SUPPORT" "=" "1"
End

TOKEN
    Name  = "DEBUG_PLATFORM"
    Value  = "0"
    Help  = "Pre-define for CRB component if Core less or equal 5.12. According to AMI_Aptio_5.x_Module_Developer's_Guide_INT.doc the domain will be support in the Core5.13."
    TokenType = Integer
    TargetH = Yes
End

PATH
	Name  = "MdeModulePkg_Lib_DIR"
	Path  = "MdeModulePkg/Library"
End

PATH
	Name  = "MdePkg_Lib_DIR"
	Path  = "MdePkg/Library"
End

#ELINK
#	Name  = "{ 32, 0xc, 0x2010, 0x0 },"
#	Parent  = "USBR_OHCI_CONTROLLER_PCI_REGISTER_VALUE"
#	Priority  = 0
#	Help  = "Latency timer and cache line size"
#	Token = "PEI_OHCI_SUPPORT" "=" "1"
#	InvokeOrder = AfterParent
#End
#
#ELINK
#	Name  = "{ 32, 0x40, 0x100, 0x0 },"
#	Parent  = "USBR_OHCI_CONTROLLER_PCI_REGISTER_VALUE"
#	Priority  = 0
#	Help  = "Disable MSI"
#	Token = "PEI_OHCI_SUPPORT" "=" "1"
#	InvokeOrder = AfterParent
#End
#
#ELINK
#	Name  = "{0x0, 0x12, 0x0},{0x0, 0x13, 0x0},{0x0, 0x14, 0x5},{0x0, 0x16, 0x0}"
#	Parent  = "USBR_OHCI_CONTROLLER_PCI_ADDRESS"
#	Token = "PEI_OHCI_SUPPORT" "=" "1"
#	InvokeOrder = AfterParent
#End

INFComponent
	Name  = "BasePlatformHookLibNull"
	File  = "BasePlatformHookLibNull/BasePlatformHookLibNull.inf"
	Package  = "MdeModulePkg"
	Path  = "MdeModulePkg_Lib_DIR"
End

INFComponent
	Name  = "BaseSerialPortLibNull"
	File  = "BaseSerialPortLibNull/BaseSerialPortLibNull.inf"
	Package  = "MdePkg"
	Path  = "MdePkg_Lib_DIR"
	Help  = "Build pass for 5.004_UefiCpuPkg_03 if there is no SIO-Serial port component."
End

INFComponent
    Name  = "BaseSerialPortLib16550"
    File  = "BaseSerialPortLib16550/BaseSerialPortLib16550.inf"
    Package  = "MdeModulePkg"
    Path  = "MdeModulePkg_Lib_DIR"
End

LibraryMapping
	Class  = "PlatformHookLib"
	Instance  = "MdeModulePkg.BasePlatformHookLibNull"
	Token = "NO_SIO_SUPPORT" "=" "1"
	Token = "AmdCpmPlatformHookLib_SUPPORT" "=" "0"
End

LibraryMapping
	Class  = "SerialPortLib"
	Instance  = "MdePkg.BaseSerialPortLibNull"
	Help  = "Build pass for 5.004_UefiCpuPkg_03 if there is no SIO-Serial port component."
#	Token = "NO_SIO_SUPPORT" "=" "1"
	Token = "FCH_UART_DEBUG_SELECT" "=" "0"
End

PcdMapping
	Name  = "PcdUseNewImageOnFlashUpdate"
	GuidSpace  = "gAmiModulePkgTokenSpaceGuid"
	PcdType  = "PcdsFixedAtBuild"
	DataType  = "Boolean"
	Value  = "FALSE"
	Offset  = 00h
	Length  = 01h
	TargetDSC = Yes
End

TOKEN
    Name  = "SOLUTION_TYPE"
    Value  = "0"
    Help  = "0 = Enable Fp5 Support, 1 = Enable Am4 support"
    TokenType = Integer
    TargetMAK = Yes
    TargetH = Yes
End

TOKEN
   Name  = "NUMBER_OF_MEM_MODULE"
  Value  = "4"
   Help  = "Number of Memory Modules in this Physical Array.\Port 'get_mem_module_info' from NBSMBIOS.ASM"
   TokenType = Integer
   TargetEQU = Yes
   TargetH = Yes
End

TOKEN
   Name  = "A1_MEMORY_SOCKETS"
  Value  = "4"
   Help  = "Number of Memory Modules/Slots in the first physical Memory Array"
   TokenType = Integer
   TargetEQU = Yes
   TargetH = Yes
End

TOKEN
   Name  = "DIMM_SLOTS_PER_NODE"
  Value  = "4"
   Help  = "Number of DIMM slots per node"
   TokenType = Integer
   TargetH = Yes
End

TOKEN
	Name  = "TYPE16_STRUCTURE"
	Value  = "0"
	Help  = "ON  -> Physical Memory Array Information structure will be present\OFF -> Physical Memory Array Information structure will not be present"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "MEMORY_DEVICE_INFO"
	Value  = "0"
	Help  = "ON   -> Memory Device Mapped Address Information (Type 20) structures will be present.\OFF  -> Memory Device Mapped Address Information (Type 20) structures will not be present."
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "WDT_SUPPORT"
	Value  = "0"
	Help  = "Enables Watchdog Timer (WDT) Support in Project"
	TokenType = Boolean
	TargetH = Yes
End

#TOKEN
#	Name  = "FCH_LPC_CLK_RUN_SUPPORT"
#	Value  = "0"
#	Help  = " LPC Clock Run support"
#	TokenType = Boolean
#	TargetH = Yes
#End

PcdMapping
    Name  = "PcdAmdSmbiosT16MaximumCapacity"
    GuidSpace  = "gEfiAmdAgesaPkgTokenSpaceGuid"
    PcdType  = "PcdsFixedAtBuild"
    DataType  = "UINT32"
    Value  = "0x02000000"
    Help  = "Maximum memory size.\ This Pcd will depend on platform configuration.\ For example, solder down DIMM or memory channel number could cause different maximum capacity."
    TargetDSC = Yes
End

#ELINK
#  Name  = "= $(EDK_TOOLS_PATH)\iasl5"
#  Parent  = "MSFT:*_*_*_ASL_PATH"
#  InvokeOrder = AfterParent
#End

#ELINK
#    Name ="MSFT:*_*_*_ASL_PATH"
#    Type="BuildOptions"
#    InvokeOrder= ReplaceParent
#    OutDsc=Yes
#End