Commit Graph

30384 Commits

Author SHA1 Message Date
NeilBrown
a94213b1fa [PATCH] md: Allow resync_start to be set and queried via sysfs
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:40 -07:00
NeilBrown
d4dbd0250e [PATCH] md: Allow raid 'layout' to be read and set via sysfs
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown
45dc2de1e5 [PATCH] md: Allow rdev state to be set via sysfs
The md/dev-XXX/state file can now be written:

 "faulty" simulates an error on the device
 "remove" removes the device from the array (if it is not busy)

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown
9e653b6342 [PATCH] md: Set/get state of array via sysfs
This allows the state of an md/array to be directly controlled via sysfs and
adds the ability to stop and array without tearing it down.

Array states/settings:

 clear
     No devices, no size, no level
     Equivalent to STOP_ARRAY ioctl
 inactive
     May have some settings, but array is not active
        all IO results in error
     When written, doesn't tear down array, but just stops it
 suspended (not supported yet)
     All IO requests will block. The array can be reconfigured.
     Writing this, if accepted, will block until array is quiescent
 readonly
     no resync can happen.  no superblocks get written.
     write requests fail
 read-auto
     like readonly, but behaves like 'clean' on a write request.

 clean - no pending writes, but otherwise active.
     When written to inactive array, starts without resync
     If a write request arrives then
       if metadata is known, mark 'dirty' and switch to 'active'.
       if not known, block and switch to write-pending
     If written to an active array that has pending writes, then fails.
 active
     fully active: IO and resync can be happening.
     When written to inactive array, starts with resync

 write-pending (not supported yet)
     clean, but writes are blocked waiting for 'active' to be written.

 active-idle
     like active, but no writes have been seen for a while (100msec).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown
4254376914 [PATCH] md: Don't write dirty/clean update to spares - leave them alone
- record the 'event' count on each individual device (they
  might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
  block only needs to be updated to record a clean<->dirty
  transition.
- Prefer odd event numbers for dirty states and even numbers
  for clean states
- Using all the above, don't update the superblock on
  a spare device if the update is just doing a clean-dirty
  transition.  To accomodate this, a transition from
  dirty back to clean might now decrement the events counter
  if nothing else has changed.

The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown
07d84d109d [PATCH] md: Allow re-add to work on array without bitmaps
When an array has a bitmap, a device can be removed and re-added and only
blocks changes since the removal (as recorded in the bitmap) will be resynced.

It should be possible to do a similar thing to arrays without bitmaps.  i.e.
if a device is removed and re-added and *no* changes have been made in the
interim, then the add should not require a resync.

This patch allows that option.  This means that when assembling an array one
device at a time (e.g.  during device discovery) the array can be enabled
read-only as soon as enough devices are available, but extra devices can still
be added without causing a resync.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown
3285edf152 [PATCH] md: Fix bug that stops raid5 resync from happening
As data_disks is *less* than raid_disks, the current test here is obviously
wrong.  And as the difference is already available in conf->max_degraded, it
makes much more sense to use that.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
akpm@osdl.org
b3cc9ec76b [PATCH] md: Fix Kconfig error
RAID5 recently changed to RAID456

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
Justin Piszcz
4d2554d045 [PATCH] md: md Kconfig speeling feex
I was experimenting with Linux SW raid today and found a spelling error when
reading the help menus...  (and fly spell found more).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown
8838832830 [PATCH] md: Calculate correct array size for raid10 in new offset mode
The size calculation made assumtion which the new offset mode didn't
follow.  This gets the size right in all cases.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown
ce25c31bdd [PATCH] md: Change md/bitmap file handling to use bmap to file blocks-fix
Fix problems with new bmap based access to bitmap files.

1/ When not using a file based bitmap, attach a NULL list of buffers
   to each page so the common free_buffer routine can cope.
2/ Use submit_bh to read as well as write, rather than vfs_read.
   This makes read and write more symetric.
3/ sync the file before reading, to ensure that the page cache has no
   dirty pages that might get written out later.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown
d785a06a0b [PATCH] md/bitmap: change md/bitmap file handling to use bmap to file blocks
If md is asked to store a bitmap in a file, it tries to hold onto the page
cache pages for that file, manipulate them directly, and call a cocktail of
operations to write the file out.  I don't believe this is a supportable
approach.

This patch changes the approach to use the same approach as swap files.  i.e.
bmap is used to enumerate all the block address of parts of the file and we
write directly to those blocks of the device.

swapfile only uses parts of the file that provide a full pages at contiguous
addresses.  We don't have that luxury so we have to cope with pages that are
non-contiguous in storage.  To handle this we attach buffers to each page, and
store the addresses in those buffers.

With this approach the pagecache may contain data which is inconsistent with
what is on disk.  To alleviate the problems this can cause, md invalidates the
pagecache when releasing the file.  If the file is to be examined while the
array is active (a non-critical but occasionally useful function), O_DIRECT io
must be used.  And new version of mdadm will have support for this.

This approach simplifies a lot of code:
 - we no longer need to keep a list of pages which we need to wait for,
   as the b_endio function can keep track of how many outstanding
   writes there are.  This saves a mempool.
 - -EAGAIN returns from write_page are no longer possible (not sure if
    they ever were actually).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown
acc55e2201 [PATCH] md/bitmap: tidy up i_writecount handling in md/bitmap
md/bitmap modifies i_writecount of a bitmap file to make sure that no-one else
writes to it.  The reverting of the change is sometimes done twice, and there
is one error path where it is omitted.

This patch tidies that up.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown
0cdd02cabd [PATCH] md/bitmap: remove dead code from md/bitmap
bitmap_active is never called, and the BITMAP_ACTIVE flag is never users or
tested, so discard them both.

Also remove some out-of-date 'todo' comments.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown
a647e4bc5c [PATCH] md/bitmap: remove unnecessary page reference manipulations from md/bitmap code
md/bitmap gets a collection of pages representing the bitmap when it
initialises the bitmap, and puts all the references when discarding the
bitmap.

It also occasionally takes extra references without any good reason, and
sometimes drops them ...  though it doesn't always drop them, which can result
in a memory leak.

This patch removes the unnecessary 'get_page' calls, and the corresponding
'put_page' calls.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown
e16b68b6e4 [PATCH] md/bitmap: use set_bit etc for bitmap page attributes
In particular, this means that we use 4 bits per page instead of a whole
unsigned long.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown
ec7a3197f4 [PATCH] md/bitmap: cleaner separation of page attribute handlers in md/bitmap
md/bitmap has some attributes per-page.  Handling of these attributes in
largely abstracted in set_page_attr and clear_page_attr.  However
get_page_attr exposes the format used to store them.  So prior to changing
that format, introduce test_page_attr instead of get_page_attr, and make
appropriate usage changes.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown
0b79ccf0cd [PATCH] md/bitmap: remove bitmap writeback daemon
md/bitmap currently has a separate thread to wait for writes to the bitmap
file to complete (as we cannot get a callback on that action).

However this isn't needed as bitmap_unplug is called from process context and
waits for the writeback thread to do it's work.  The same result can be
achieved by doing the waiting directly in bitmap_unplug.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown
d7375ab324 [PATCH] md/bitmap: fix online removal of file-backed bitmaps
When "mdadm --grow /dev/mdX --bitmap=none" is used to remove a filebacked
bitmap, the bitmap was disconnected from the array, but the file wasn't closed
(until the array was stopped).

The file also wasn't closed if adding the bitmap file failed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown
52c03291a8 [PATCH] md: split reshape portion of raid5 sync_request into a separate function
... as raid5 sync_request is WAY too big.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
Adrian Bunk
5e56341d02 [PATCH] md: make md_print_devices() static
This patch makes the needlessly global md_print_devices() static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown
c93983bf51 [PATCH] md: support stripe/offset mode in raid10
The "industry standard" DDF format allows for a stripe/offset layout where
data is duplicated on different stripes.  e.g.

  A  B  C  D
  D  A  B  C
  E  F  G  H
  H  E  F  G

(columns are drives, rows are stripes, LETTERS are chunks of data).

This is similar to raid10's 'far' mode, but not quite the same.  So enhance
'far' mode with a 'far/offset' option which follows the layout of DDFs
stripe/offset.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown
7c7546ccf6 [PATCH] md: allow a linear array to have drives added while active
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown
5fd6c1dce0 [PATCH] md: allow checkpoint of recovery with version-1 superblock
For a while we have had checkpointing of resync.  The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.

Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown
a8a55c387d [PATCH] md: remove nuisance message at shutdown
At shutdown, we switch all arrays to read-only, which creates a message for
every instantiated array, even those which aren't actually active.

So remove the message for non-active arrays.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown
16a53ecc35 [PATCH] md: merge raid5 and raid6 code
There is a lot of commonality between raid5.c and raid6main.c.  This patches
merges both into one module called raid456.  This saves a lot of code, and
paves the way for online raid5->raid6 migrations.

There is still duplication, e.g.  between handle_stripe5 and handle_stripe6.
This will probably be cleaned up later.

Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown
16f17b39f3 [PATCH] md: increase the delay before marking metadata clean, and make it configurable
When a md array has been idle (no writes) for 20msecs it is marked as 'clean'.
 This delay turns out to be too short for some real workloads.  So increase it
to 200msec (the time to update the metadata should be a tiny fraction of that)
and make it sysfs-configurable.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown
9443a1d1f7 [PATCH] md: remove useless ioctl warning
This warning was slightly useful back in 2.2 days, but is more an annoyance
now.  It makes it awkward to add new ioctls (that we we are likely to do that
in the current climate, but it is possible).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
NeilBrown
8932c2e0dc [PATCH] md: remove arbitrary limit on chunk size
The largest chunk size the code can support without substantial surgery is
2^30 bytes, so make that the limit instead of an arbitrary 4Meg.  Some day,
the 'chunksize' should change to a sector-shift instead of a byte-count.  Then
no limit would be needed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
NeilBrown
c70810b327 [PATCH] md: reformat code in raid1_end_write_request to avoid goto
A recent change made this goto unnecessary, so reformat the code to make it
clearer what is happening.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
Alasdair G Kergon
72d9486169 [PATCH] dm: improve error message consistency
Tidy device-mapper error messages to include context information
automatically.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
Alasdair G Kergon
5c6bd75d06 [PATCH] dm: prevent removal if open
If you misuse the device-mapper interface (or there's a bug in your userspace
tools) it's possible to end up with 'unlinked' mapped devices that cannot be
removed until you reboot (along with uninterruptible processes).

This patch prevents you from removing a device that is still open.

It introduces dm_lock_for_deletion() which is called when a device is about to
be removed to ensure that nothing has it open and nothing further can open it.
 It uses a private open_count for this which also lets us remove one of the
problematic bdget_disk() calls elsewhere.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
David Teigland
c2ade42dd3 [PATCH] dm: create error table
Add a library function dm_create_error_table() to create a table that rejects
any I/O sent to a device with EIO.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
Alasdair G Kergon
17b2f66f2a [PATCH] dm: add exports
Move definitions of core device-mapper functions for manipulating mapped
devices and their tables to <linux/device-mapper.h> advertising their
availability for use elsewhere in the kernel.

Protect the contents of device-mapper.h with ifdef __KERNEL__.  And throw
in a few formatting clean-ups and extra comments.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
Alasdair G Kergon
2b06cfff12 [PATCH] dm: consolidate creation functions
Merge dm_create() and dm_create_with_minor() by introducing the special value
DM_ANY_MINOR to request the allocation of the next available minor number.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
David Teigland
814d68629b [PATCH] dm table split_args: handle no input
Return sense if dm_split_args is called with a NULL input parameter.

Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
Jonathan Brassow
ce503f59ae [PATCH] dm kcopyd: error accumulation fix
kcopyd should accumulate errors - otherwise I/O failures may be ignored
unintentionally.

And invert 'success' (used in a future patch), using a more intuitive
!(read_err || write_err).

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Alasdair G Kergon
8a835f11bc [PATCH] dm mirror log: sync_count fix
When a mirror is reduced in size, clear the part of the bitmap that is no
longer used.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Alasdair G Kergon
29121bd0b0 [PATCH] dm mirror log: bitset_size fix
Fix the 'sizeof' in the region log bitmap size calculation: it's uint32_t, not
unsigned long - this breaks on some archs.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Alasdair G Kergon
b7cca195c4 [PATCH] dm mirror log: refactor context
Refactor the code that creates the core and disk log contexts to avoid the
repeated allocation of clean_bits introduced by the last patch.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Kevin Corry
702ca6f0be [PATCH] dm mirror log: sector size fix
On-disk logs for dm-mirror devices are currently hard-coded to use 512 byte
hard-sector-sizes.  This patch fixes dm-log so it will work with devices with
non-512-byte hard-sector-sizes.

To maintain full compatibility, instead of moving the clean-bits bitset to a
bitset, and enlarges the disk-header buffer to encompass both the header and
the bitset.  The I/O routines for the bitset are removed, and the I/O routines
for the disk-header now also read/write the bitset.

Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Milan Broz
143535396c [PATCH] dm table: get_target: fix last index
The table is indexed from 0, so an index equal to t->num_targets should be
rejected.

(There is no code in the current tree that would exercise this bug.)

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Neil Brown
e4c8b3ba34 [PATCH] dm: mirror sector offset fix
The device-mapper core does not perform any remapping of bios before passing
them to the targets.  If a particular mapping begins part-way into a device,
targets obtain the sector relative to the start of the mapping by subtracting
ti->begin.

The dm-raid1 target didn't do this everywhere: this patch fixes it, taking
care to subtract ti->begin exactly once for each bio.

[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Jeff Mahoney
f0b0411536 [PATCH] dm: fix block device initialisation
In alloc_dev(), we register the device with the block layer and then continue
to initialize the device.  But register_disk() makes the device available to
be opened before we have completed initialising it.

This patch moves the final bits of the initialization above the disk
registration.

[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Jeff Mahoney
10da4f795f [PATCH] dm: add module ref counting
The reference counting on dm-mod is zero if no mapped devices are open.  This
is incorrect, and can lead to an oops if the module is unloaded while mapped
devices exist.

This patch claims a reference to the module whenever a device is created, and
drops it again when the device is freed.

Devices must be removed before dm-mod is unloaded.

[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Jeff Mahoney
7ec75f2547 [PATCH] dm: fix mapped device ref counting
To avoid races, _minor_lock must be held while changing mapped device
reference counts.

There are a few paths where a mapped_device pointer is returned before a
reference is taken.  This patch fixes them.

[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:35 -07:00
Jeff Mahoney
fba9f90e56 [PATCH] dm: add DMF_FREEING
There is a chicken and egg problem between the block layer and dm in which the
gendisk associated with a mapping keeps a reference-less pointer to the
mapped_device.

This patch uses a new flag DMF_FREEING to indicate when the mapped_device is
no longer valid.  This is checked to prevent any attempt to open the device
from succeeding while the device is being destroyed.

[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:34 -07:00
Jeff Mahoney
f32c10b099 [PATCH] dm: change minor_lock to spinlock
While removing a device, another another thread might attempt to resurrect it.

This patch replaces the _minor_lock mutex with a spinlock and uses
atomic_dec_and_lock() to serialize reference counting in dm_put().

[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:34 -07:00
Jeff Mahoney
62f75c2f32 [PATCH] dm: move idr_pre_get
idr_pre_get() can sleep while allocating memory.

The next patch will change _minor_lock into a spinlock, so this patch moves
idr_pre_get() outside the lock in preparation.

[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:34 -07:00
Jeff Mahoney
ba61fdd17d [PATCH] dm: fix idr minor allocation
One part of the system can attempt to use a mapped device before another has
finished initialising it or while it is being freed.

This patch introduces a place holder value, MINOR_ALLOCED, to mark the minor
as allocated but in a state where it can't be used, such as mid-allocation or
mid-free.  At the end of the initialization, it replaces the place holder with
the pointer to the mapped_device, making it available to the rest of the dm
subsystem.

[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:34 -07:00